Abstract:Purpose Aluminum foam-filled thin-walled unit structures have received much attention for their excellent energy absorption properties. To improve the energy absorption effect of car energy absorption box under axial compression, this paper optimizes the fiber lay-up sequence, fiber angle and aluminum foam density of aluminum foam filled carbon fiber reinforced plastic (CFRP) thin-walled square tubes. Design/methodology/approach Design of sample points required to construct the proxy model using design of experiments (DOE) method, and the data sample points of different models are obtained through Abaqus simulation and test. A double high-precision proxy model with the maximum specific energy absorption (SEA) and the minimum initial peak crash force (PCF) as the evaluation index is constructed based on the response surface function method. The NSGA-II multi-objective genetic algorithm was used to optimize the design parameters and obtain the optimal solution for the Pareto front, and the results were verified by using the multi-objective optimization toolbox in design-expert. Findings The results show that the optimal solution to the multi-objective optimization problem with the inclusion of the lay-up sequence is ρ = 0.5g/cm3 for a fiber lay-up angle varying in the range ±15–90° and an aluminum foam density varying in the range 0.2g/cm3-0.5g/cm3, with a lay-up method of [±87°/±16°/±15°/±89°]. The two optimization methods correspond to SEA and PCF errors of 2.109% and 4.1828%, respectively. The optimized SEA value is 18.2 J/g and the PCF value is 18,230 N. The optimized design reduces the peak impact force and increases the specific energy absorption, which improves the energy absorption effect of thin-walled energy-absorbing boxes for automobiles. Originality/value In this paper, the impact resistance of CFRP thin-walled square tubes filled with aluminum foam is optimized. Based on numerical simulations and experiments to obtain the sample point data for constructing the dual-agent model, we investigate the effect of filling with different densities of aluminum foam under the simultaneous change of fiber lay-up angle and order on its mechanical properties in this process, and carry out the multi-objective optimization design with NSGA-II algorithm.

Automobile Crashworthiness Improvement by Energy-Absorbing Characterisation of Aluminium Foam Porosity

Experiment and numerical simulation of anti-penetration performance of composite structures

Mechanical properties and energy absorption capabilities of aluminium foam sandwich structure subjected to low-velocity impact

On low-velocity impact response of foam-core sandwich panels

Impact Resistance of Aluminum Foam Composites with Filler and Coating Materials

Compressive behavior and energy absorption analysis of casting skin-wrapped aluminum foams

Crashworthiness of foam filled truncated conical sandwich shells with corrugated cores

Crashworthiness study of aluminum foam-filled tubular lattice structures based on triply periodic minimal surface metamaterials under lateral crushing

An Investigation on Axial Deformation Behavior of Thin-Wall Unfilled and Filled Tube with Aluminum Alloy (Al-Si7Mg) Foam Reinforced with SiC Particles

Energy-absorbing mechanism and crashworthiness performance of thin-walled tubes diagonally filled with rib-reinforced foam blocks under axial crushing

Optimized design of energy absorption of aluminum foam filled CFRP thin-walled square tube based on agent model

Crashworthiness Study of a Newly Developed Civil Aircraft Fuselage Section with Auxiliary Fuel Tank Reinforced with Composite Foam

Study on Quasi-Static Compressive Properties of Aluminum Foam-Epoxy Resin Composite Structures

Aluminum Foam Sandwiches: A Lighter Future for Car Bodies

Axial Impact Performances of Composite Aluminum Foam Tubes

The mechanical characteristics of an aluminum foam winding CFRP composite structure under axial compression

Effects of Aluminum Foam Filling on Compressive Strength and Energy Absorption of Metallic Y-Shape Cored Sandwich Panel

Experimental Studies on the Axial Crash Behavior of Aluminum Foam-Filled Hat Sections

Dynamic response and energy absorption of aluminum foam sandwich under low-velocity impact

Modeling and testing of energy absorbing lightweight materials and structures for automotive applications

Effect of high-density structural foam on crashworthiness of vehicle front side-rail and its application