Abstract:Using pyromelliticdianhydride (PMDA) and polyfunctional epoxy ether (PFE) as branching agent, long chain branching stereocomplex poly(L‐lactide)s and poly(D‐lactide)s was prepared by reactive processing, respectably. Then stereocomplex poly(lactide)s of long chain branching PLLA and PDLA (sc‐PLA/BA) was prepared by solution blending and its fabricated the vascular stents via 3D‐printing.The effects of branching structure on melt crystallization behavior of sc‐PLA/BA investigated by DSC. The influence of the branching agent content on the crystallization ability of samples shows a bell‐shaped relationship, there is a maximum point when the branching agent content is1.5 wt%. When the branching agent content is less than 1.5 wt%, the crystallization ability of the sample increased with the increasing of branching agent content. When the branching agent content exceeded than 1.5 wt%, the crystallization ability of the samples decreased with branching agent content increasing. Such behavior is as the linear PLA branched to dendrite configuration, the enrichment of segments around branching structure within branched chains promoted its nucleation. But the high degree of branching caused inter‐ or intrachians entanglement which obstructed the segments movement and growth into the crystals. The half‐time of crystallization (t1/2) of the samples decreased from 6 minutes for initial sc‐PLA/BA‐0 to 3 minutes of sc‐PLA/BA‐1.5 wt% at 163°C. POM results indicated that nucleation density of sc‐PLA/BA significantly increased with the branching agent increasing. Moreover, mechanical testing demonstrated that forming branching structure could be an effective modification of the mechanical properties for sc‐PLA, its tensile strength and modulus increases from 57.3 MPa and 2.02 GPa to 70.4 MPa and 3.31 GPa, respectively. TGA results analyzed by FWO method and Kissinger method, indicated the apparent activation energy of sc‐PLA/BA samples increases from 96.8 to 113.3 kJ/mol, suggesting the improvement of heat resistance. The CCK‐8 assay, ALP assay and cell Live/Dead assay results indicated that sc‐PLA with branching structure presented very low cell cytotoxicity. Therefore, the long chain branching sc‐PLA matrix with branching agent could effectively improve its crystallization abilities, mechanical properties, heat resistance and biocompatibilities.

Microstructure–property Relationship of L-Lactide/trimethylene Carbonate/glycolide Terpolymers As Cardiovascular Stent Material

Poly(L-Lactic Acid)-Block-Poly(Butylene Succinate-Co-Butylene Adipate) Multiblock Copolymers: from Synthesis to Thermo-Mechanical Properties

In Vivo Degradation of Copolymers Prepared from L-Lactide, 1,3-Trimethylene Carbonate and Glycolide As Coronary Stent Materials

Synthesis and Properties of Trimethylene Carbonate-L-Lactide-Glycolide Terpolymers

In Vitro Degradation of Poly[(L‐lactide)‐co‐(trimethylene Carbonate)] Copolymers and a Composite with Poly[(L‐lactide)‐co‐glycolide] Fibers As Cardiovascular Stent Material

Effect of Trimethylene Carbonate Segments on the Structure and Properties of Poly(l‐lactide‐glycolide‐trimethylene Carbonate) Terpolymers for Biodegradable Vascular Stents

In Vitro Degradation Behavior of L-Lactide/Trimethylene Carbonate/Glycolide Terpolymers and A Composite with Poly(L-Lactide-Co-Glycolide) Fibers

In Vitro Biocompatibility Evaluation of Bioresorbable Copolymers Prepared from L-Lactide, 1, 3-Trimethylene Carbonate, and Glycolide for Cardiovascular Applications

In Vivo Study on the Histocompatibility and Degradation Behavior of Biodegradable Poly(Trimethylene Carbonate-Co-D,L-Lactide)

Totally Bioresorbable Composites Prepared from Poly(l‐lactide)‐co‐(trimethylene Carbonate) Copolymers and Poly(l‐lactide)‐co‐(glycolide) Fibers As Cardiovascular Stent Material

Cytocompatibility Evaluation of a Novel Series of PEG-Functionalized Lactide-Caprolactone Copolymer Biomaterials for Cardiovascular Applications

Enhancement of the crystallization and biocompatibility of poly(TMC-b-(LLA-ran-GA)) by poly(lactide) stereocomplex

Evaluation of Bioresorbable Polymers As Potential Stent Materialin Vivo Degradation Behavior and Histocompatibility

Structure, Properties, and in Vitro Degradation Behavior of Biodegradable Poly(l‐lactic Acid)‐trimethylene Carbonate‐glycolide Terpolymer

Biodegradable Poly(trimethylene Carbonate‐b‐(l‐lactide‐ran‐glycolide)) Terpolymers with Tailored Molecular Structure and Advanced Performance

<scp>3D</scp> printed peripheral vascular stents based on degradable poly(<scp>trimethylene carbonate‐b‐(L‐lactide‐ran‐glycolide)</scp>) terpolymer

Regulating mechanical performance of poly (l-lactide acid) stent by the combined effects of heat and aqueous media

3D printed peripheral vascular stents based on degradable poly(trimethylene carbonate-b-(L-lactide-ran-glycolide)) terpolymer

Haemo- and cytocompatibility of bioresorbable homo- and copolymers prepared from 1,3-trimethylene carbonate, lactides, and ε-caprolactone

In vitro degradation and biocompatibility evaluation of fully biobased thermoplastic elastomers consisting of poly(β-myrcene) and poly( -lactide) as stent coating

Stereocomplex Poly(lactic Acid) Vascular Stents by 3d‐printing with Long Chain Branching Structures: Toward Desirable Crystallization Properties and Mechanical Performance