Abstract:The aluminum alloy AlSi5Cu2Mg finds application in the production of high-stress cylinder head castings. The AlSi5Cu2Mg alloy is specific for its high susceptibility to hot tearing. One effective way to reduce the susceptibility of Al-Si-Cu-Mg alloys to hot tearing is by grain refining. The AlSi5Cu2Mg alloy is designed with a specific chemical composition that significantly limits the Ti content to a maximum of 0.03 wt.%. This limitation practically limits the use of standard Al-Ti-B-based refiners. The present work focuses on the investigation of the influence of graded Ti addition on the susceptibility of the AlSi5Cu2Mg alloy to hot tearing. The Ti addition was deliberately chosen beyond the manufacturer's recommendation (0.1, 0.2, 0.3 wt.%). The solidification process of the experimental alloys with Ti addition was evaluated in this research. On the basis of the thermal analysis, it was shown that due to the addition of Ti, the solidification interval of the AlSi5Cu2Mg alloy increases. An increase in the solidification interval is often associated with an increase in the susceptibility to tearing. The susceptibility of the experimental alloys to hot tearing was evaluated qualitatively and quantitatively. Based on the quantitative and qualitative evaluation, it was shown that the addition of Ti reduces the susceptibility of the AlSi5Cu2Mg alloy to hot tearing. A positive refining effect of Ti on the primary α-(Al) phase was demonstrated by microstructural evaluation. Based on this research, it was shown that despite the increase in the solidification interval due to the addition of Ti, the susceptibility of the aluminum alloy to the formation of hot tears is reduced due to the better filling of the material in the interdendritic spaces.

Hot Tearing Susceptibility of TiB2-reinforced Al–5Cu Matrix Composite

Improvement of Yttrium on the Hot Tearing Susceptibility of 6Tib2/al-5Cu Composite

Effect of Ti Addition on the Hot-Tearing Susceptibility of the AlSi5Cu2Mg Alloy

Effects of TiB2 Particles on Microstructure and Mechanical Properties of an In-Situ TiB2-Al–Cu–Li Matrix Composite

Effect of TiB2 on Microstructure, Mechanical Properties and Oxidation Resistance of TiAl-based Alloys

Impact behavior of in situ TiB<sub>2</sub>/Al composite at various temperatures

Investigation of the Hot Deformation Behavior and Microstructure Evolution of TiB2 +tial3/2024al Composite

Investigation on Fracture Toughness of Aluminum Matrix Composites Reinforced with in Situ Titanium Diboride Particles

Impact behavior of in situ TiB 2 /Al composite at various temperatures

Deformation, Fracture, and Fatigue Crack Growth Behavior in TiB-reinforced Near-Α Ti Matrix Composites Fabricated Using Powder Metallurgy Technique

Effects of Nanosized Particles on Microstructure and Mechanical Properties of an Aged In-Situ TiB2/Al-Cu-Li Composite

Effect of TiB2 particles on thermal deformation behavior and mechanical properties of aluminum alloy

Mechanical Properties and Fracture Morphology of In-situ TiB2 Particle Reinforced Aluminum Matrix Composites

Effect of Y on the hot tearing susceptibility of 3Y2O3/Al5Cu composite

Enhanced High Temperature Mechanical Properties and Heat Resistance of an Al–Cu–Mg–Fe–Ni Matrix Composite Reinforced with In-Situ TiB 2 Particles

Enhanced high temperature mechanical properties and heat resistance of an Al–Cu–Mg–Fe–Ni matrix composite reinforced with in-situ TiB2 particles

Effects of Trace Reinforcements on Microstructure and Tensile Properties of In-Situ Synthesized TC18 Ti Matrix Composite

Effect of Al Content on Hot Tearing Susceptibility of Mg–5Zn–0.6Mn–xAl–0.6Zr Alloys

Investigation on the High-Temperature Ductility and Fracture Mechanisms of an In-Situ Particle Reinforced Al Matrix Composite 7075Al/tib2

Microstructure and Mechanical Properties of Aluminum Matrix Composites Reinforced With In-Situ TiB2 Particles

Effects of TiB2 particle and local aspect ratio on microstructure and mechanical properties of an I-shaped TiB2/6061Al composite profile