Abstract:In order to improve the bonding strength between calcium phosphate/chitosan composite coatings and a micro-arc oxidized (MAO)-AZ91D Mg alloy, different influencing parameters were investigated in the process of electrophoretic deposition (EPD) followed by conversion in a phosphate buffer solution (PBS). Surface morphology and phase constituents of the as-prepared materials were investigated by using X-ray diffractometer (XRD), Fourier-transformed infrared spectrophotometer (FTIR), Raman spectrometer, scanning electron microscope (SEM) with an energy dispersive spectrometer (EDS), and a thermo gravimetric and differential thermal analyzer (TG-DTA). Scratch tests were carried out to study the bonding properties between the coatings and the substrates. In vitro immersion tests were conducted to determine the corrosion behaviors of samples with and without deposit layers through electrochemical experiments. In the EPD process, the acetic acid content in the electrophoresis suspension and the electrophoretic voltage played important roles in improving the bonding properties, while the contents of chitosan (CS) and nano-hydroxyapatite (nHA, Ca-10(PO4)(6)(OH)(2)) in the suspension had less significant influences on the mechanical bonding strength. It was observed that the coatings showed the excellent bonding property when an electrophoretic voltage was in a range of 40-110 V with other reagent amounts as follows: acetic acid: 4.5 vol.%, CS <= 0.25 g, nHA <= 2.0 g in 200 ml of a CS-acetic acid aqueous solution and nHA <= 2.5 g in 300 ml of absolute ethanol. The morphology of the composite coating obtained under the above optimal condition had a flake-like crystal structure. The EPD in the nHA/CS-acetic acid/ethanol suspension resulted in hydroxyapatite, chitosan, brushite (DCPD, CaHPO4 center dot 2H(2)O) and Ca(OH)(2) in the coatings. After the as-prepared coating materials were immersed into PBS, Ca(OH)(2) could be converted into HA and DCPD. The results of the electrochemical tests manifested that the corrosion resistance of the Mg alloy was improved by coating this composite film. (C) 2012 Elsevier B. V. All rights reserved.

Investigation on the Compound Phosphate Film Formed in Bath with Cerium Salts on the Magnesium Aluminum Alloy

Study on structure and properties of microarc oxidation coating on magnesium alloy in phosphate-potassium hydroxide solution

The Formation Mechanism And Corrosion Resistance Of A Composite Phosphate Conversion Film On Am60 Alloy

The Research of Molybdate and Molybdate-phosphate Conversion Films on Magnesium Alloy

Study on the Phosphate/electrophoretic Composite Coatings on Mg Alloy: the Effect of Phosphate Conversion Films on Adhesion Strength and Corrosion Resistance

The Study of a Phosphate Conversion Coating on Magnesium Alloy AZ91D: III. Nano-particle Modification

Structure and Formation Mechanism of Phosphate Conversion Coating on Die-Cast Az91d Magnesium Alloy

Preparation of Composite Molybdate/Phosphate Conversion Coating on Mg Alloys

An Investigation of the Effect of a Magnetic Field on the Phosphate Conversion Coating Formed on Magnesium Alloy

Nano Al2O3/phosphate composite conversion coating formed on magnesium alloy for enhancing corrosion resistance

Formation Mechanism of Phosphate Conversion Film on Mg–8.8Li Alloy

An Optimization of Pretreatment for the Phosphate Conversion Film on WE43 Magnesium Alloy

A Study and Application of Zinc Phosphate Coating on Az91d Magnesium Alloy

Influence of Additive on Structure and Corrosion Resistance of Manganese Phosphate Film on Az91 Magnesium Alloy

In Situ Formation of Organophosphonate Film on Mg Alloy with Corrosion Inhibiting Behavior

Effect of Ca2+on Phosphate Conversion Coating on Magnesium Alloy

Deposition and corrosion performance of phosphate-polylactic acid composite coatings on WE43 magnesium alloy

Novel Phosphate Conversion Coating with Superior Corrosion Resistance on the Mg-Al-RE Alloy Based on the Introduction of Silane

Preparation of Conductive and Corrosion Resistant Phosphate Conversion Coating on AZ91D Magnesium Alloy

Study on the Bonding Strength Between Calcium Phosphate/chitosan Composite Coatings and a Mg Alloy Substrate

Degradation of calcium/phosphorus coating plasma sprayed on magnesium alloy in SBF solution