Abstract:Cubic Boron Nitride (cBN), a kind of super abrasive material with excellent properties, is widely applied into the manufacturing of high end grinding tools especially for high speed machining fields. During the actual grinding process, abrasive failure phenomena take place, which affects the grinding tool performance, and then the final machining quality. Considering the high speed applicability of cBN grinding tools, it is of significance to investigate the failure mechanism and grinding performance of cBN abrasives at different grinding speeds, in particular under high speed condition. Therefore, this paper carries out an investigation of cBN abrasive failure behavior taking grinding speed sensitivity into consideration. Given that the random and diversity of multi-abrasives distributed upon grinding tools contributes to the complexity of the study, single cBN abrasive cutting experiments are conducted under four grinding speed levels of 40, 60, 80 and 100 m/s, respectively. When all experiments are completed, abrasive failure patterns can be identified through observation on the morphology of ground cBN abrasives bonded on cutting inserts using Scanning Electron Microscope (SEM). Based on the analysis of experimental results, it is shown that for the cBN abrasives studied in this paper, abrasive breakage occurs at low grinding speed, but as speed increases, cBN abrasives tend to get worn. The change of grinding forces, as well as roughness Ry values, can show the detailed failure behavior of tested cBN abrasives with time dependent features. In addition, G ratio rises with the increase of grinding speed, which demonstrates the high productivity potential of cBN high speed grinding. Finally, an in-depth analysis concerning on cBN material’s crystal characteristics and energy threshold (binding energy) is discussed, which provides an intrinsic explanation on the influence of grinding speed upon cBN abrasive failure mechanism.

Time Dependent Behavior Analysis of Inconel 718 in High Speed Grinding Process

Experimental Study of Time-Dependent Performance in Superalloy High-Speed Grinding with Cbn Wheels

Theoretical Generalization and Research on the Mechanism of the Unsteady-State Grinding Technique

Numerical Investigation of the Evolution of Grit Fracture and Its Impact on Cutting Performance in Single Grit Grinding

Surface Characteristics and Roughness Prediction of TC4 Titanium Alloy in High Speed Grinding

Studies on the Surface Quality of the Unsteady-State Grinding Technique

Study on the grinding of Inconel 718

Effect of intermittent cutting behavior on the ultrasonic vibration-assisted grinding performance of Inconel718 nickel-based superalloy

An Experimental Investigation on Response of Cbn Super Abrasive’s Grinding Performance and Failure Characteristics to the Grinding Speed

Study on Grindability of Inconel 718 Superalloy Fabricated by Selective Laser Melting (SLM)

Effects of a New Type of Grinding Wheel with Multi-Granular Abrasive Grains on Surface Topography Properties after Grinding of Inconel 625

Comparative Investigation on Grindability of Inconel 718 Made by Selective Laser Melting (SLM) and Casting

IM (indentation Method) Based Impact Fracture Characteristics of Cbn Crystal and Their Influence on High Speed Wheel Performance

Alumina abrasive wheel wear in ultrasonic vibration-assisted creep-feed grinding of Inconel 718 nickel-based superalloy

Study on High-Shear and Low-Pressure Grinding Using Super-Elastic Composite Abrasive Tool (ECAT) for Curved Inconel718 Workpiece

Effect of process parameters on hardness and microstructure of 18CrNiMo7-6 carburized steel in high-speed cylindrical grinding

EXPERIMENTAL INVESTIGATION ON SURFACE INTEGRITY OF END MILLING NICKEL-BASED ALLOY— INCONEL 718

Analysis of the material removal and heat transfer during internal cooling grinding of GH4169

Process parameter optimization and surface integrity evolution in the high-speed grinding of TiAl intermetallics based on grey relational analysis method

Mechanisms of abrasive wear in the grinding of titanium (TC4) and nickel (K417) alloys

Investigation of the grinding temperature and subsurface quality of a novel point grinding wheel