Abstract:With the continuous improvement of various armor protection technologies, the armor protection performance has increased significantly, and then the damage performance requirements of armor-piercing ammunition have also increased. In order to improve the penetration ability of the liner, a new three-layer liner structure is designed in this paper. The jet forming process was simulated by AUTODYN software. The mechanism of shaped jet forming of three-layer liner was studied. The reason why the penetration depth of three-layer liner was higher than that of ordinary liner was explained. The influence of three-layer liner on the propagation of detonation wave and the change of pressure when detonation wave acted on liner were found, which provided a new idea for improving the penetration depth of jet. The influence of liner material, cone angle and stand-off on jet forming and penetration was also studied by orthogonal optimization experiment, and the structural parameters with the best penetration performance were obtained. The results show that the pressure at the convergence point increases first and then decreases during the formation of the jet of the three-layer liner. The pressure at the convergence point when the three-layer liner material is from low impedance to high impedance from the outside to the inside is much larger than the pressure at the convergence point from high impedance to low impedance. When the three-layer liner material is Al 2024-Copper–Tantalum from the outside to the inside, the pressure at the convergence point of the three-layer liner at different times is higher than that of the double-layer liner and the single-layer liner. Reasonable matching of different impact impedance materials in the three-layer liner can greatly improve the pressure value of the detonation wave acting on the cone liner. The maximum pressure at the convergence point on the axis is 39.10 GPa, which is 22.00% higher than that of the double-layer liner at the convergence point, and 53.03% higher than that of the single-layer liner at the convergence point. The orthogonal design test scheme is simulated and analyzed. The penetration depth is taken as the observation index, and the range analysis is adopted. The results show that the material matching of the three-layer liner has the greatest influence on the depth of the jet penetrating the target plate, followed by the cone angle of the three-layer liner. Relatively speaking, the stand-off has the least influence on the result. Reasonable matching of materials with different impact impedances in the three-layer liner can maximize the penetration depth of the jet into the target plate.

Influence of Different Combinations of Explosively Welded Plates with the Same Areal Density on Their Antipenetration Performance

Numerical Study on the Perforation of Steel Plates by Multiple Projectiles

Experimental and numerical investigation on the anti-penetration performance of metallic sandwich plates for marine applications

Investigation on the anti-penetration performance of the steel/nylon sandwich plate

Experimental and Numerical Investigation on Ballistic Penetration Performance of TC4-Al3Ti Layered Composites by Hot Rolling

Research on anti-penetration performance of composite armor of steel/composite materials

Simulation of ballistic performance of a two-layered structure of nanostructured metal and ceramic

Penetration of Disk Fragments Following Impact on Thin Plate

Numerical simulation of the disk fragment impacting resistance of plate target

Numerical Simulation on the Anti-Penetration Performance of Polyurea-Core Weldox 460 E Steel Sandwich Plates

Evaluation of the Impact Resistance of Steel–Aluminum Laminated Target Plates with Isoplanar Density

Experimental investigation on the ballistic resistance of monolithic and multi-layered plates against hemispherical-nosed projectiles impact

Ballistic Limit of High-Strength Steel and Al7075-T6 Multi-Layered Plates Under 7.62-mm Armour Piercing Projectile Impact

Experimental investigation on the ballistic performance of double-layered plates subjected to impact by projectile of high strength

On the ballistic resistance of double-layered steel plates: An experimental and numerical investigation

The effect of dietary levels of folate and cobalamin on the serum concentration of folate and cobalamin in the dog.

Numerical investigation on dynamic damage behavior of a novel N-shaped perforated armor plate under ballistic impact

Investigation on the influence of strength and density of jacket materials on the penetration performance of jacketed rods

Study on the detonation wave propagation of shaped charge with three-layer liner and its driving characteristics to liner

Numerical Simulation of Multifunctional Projectile Penetrating Reinforced Concrete Target Plate Based on Sensor Data Acquisition

Enhanced ballistic resistance of multilayered cross-ply UHMWPE laminated plates