Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Strength and ductility performance of concrete-filled steel tubular columns after long-term service loading

Seismic Behavior of Concrete-Filled Wide Rectangular Steel Tubular (CFWRST) Stub Columns

Design Of Concrete-Filled Steel Tubular Chs Connections In Tension

Concrete-Filled Double Skin Steel Tubular (cfdst) Columns Subjected to Long-Term Sustained Loading

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Combined Axial and Flexural Behavior of Concrete-Filled Corrugated Steel Tubular Columns

Experimental Studies On The Strength With High Slenderness Ratio Concrete Filled Steel Tubular Columns

Influence of long-term loading on the performance of concrete-filled double skin steel tubular columns: Experiments

Concrete-filled steel tubes subjected to axial compression: Life-cycle based performance

Strength, Stiffness and Ductility of Concrete-Filled Steel Columns under Axial Compression

Passive stress-strain model and ultimate strength prediction for short steel tube confined concrete (STCC) columns allowing for size effect

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns

Experimental and numerical studies of axially loaded square concrete‐encased concrete‐filled large‐diameter steel tubular short columns

Experimental and numerical behavior of eccentrically loaded square concrete-filled steel tubular long columns made of high-strength steel and concrete

Performance test and Finite-element analysis of high strength concrete-filled steel tubular columns under axial compression

Static Behaviors of Reinforcement-Stiffened Square Concrete-Filled Steel Tubular Columns

Finite Element Modelling of Concrete-Filled Steel Stub Columns under Axial Compression

Analytical Behavior of Concrete-Encased CFST Columns under Cyclic Lateral Loading

Behaviour of Concrete-Encased CFST Stub Columns Subjected to Long-Term Sustained Loading

Experimental and numerical investigation of square concrete-filled double-skin steel stiffened tubular stub columns with CHS inner tubes under axial compression

MECHANICAL BEHAVIOR AND PARAMETRIC STUDY OF CONCRETE-FILLED STEEL TUBULAR STUB COLUMNS WITH ENCASED PROFILED STEEL UNDER AXAIL COMPRESSION