Ex Situ Hydrodeoxygenation in Biomass Pyrolysis Using Molybdenum Oxide and Low Pressure Hydrogen

Michael W. Nolte,Jing Zhang,Brent H. Shanks

DOI: https://doi.org/10.1039/c5gc01614b

IF: 9.8

2016-01-01

Green Chemistry

Abstract:Vapors from corn stover pyrolysis were deoxygenated to aromatics and alkanes with low pressure hydrogen over MoO3.

What problem does this paper attempt to address?

In Situ Synthesis of Molybdenum Oxide@n-Doped Carbon from Biomass for Selective Vapor Phase Hydrodeoxygenation of Lignin-Derived Phenols under H2atmosphere

Lujiang Xu,Zheng Han,Ying Zhang,Yao Fu

DOI: https://doi.org/10.1039/c6ra21989f

IF: 4.036

2016-01-01

RSC Advances

Abstract:We report a simple, green method to prepare molybdenum oxide@N-doped carbon (MoOx@NC)via in situpyrolysis of molybdenum precursor preloaded cellulose and demonstrate its catalytic performance for vapor phase HDO of lignin-derived phenols.
Reactive Catalytic Fast Pyrolysis of Biomass over Molybdenum Oxide Catalysts: A Parametric Study

Phillip Cross,Kaige Wang,Joseph Weiner,Elliot Reid,Jonathan Peters,Ofei Mante,David C. Dayton

DOI: https://doi.org/10.1021/acs.energyfuels.0c00320

IF: 4.6541

2020-01-01

Energy & Fuels

Abstract:Reactive catalytic fast pyrolysis (RCFP) of biomass with atmospheric pressure hydrogen is a promising route for the deoxygenation of biomass pyrolysis vapors while retaining high carbon yields in the bio-crude. RCFP process development was accomplished in a bench-scale bubbling fluidized-bed reactor with in situ catalyst configuration. Results are presented that highlight the impact of temperature, biomass weight hourly space velocity (WHSV), reaction pressure, and time on stream on the hydrodeoxygenation of different oxygen-containing species produced during biomass reactive catalytic fast pyrolysis to improve the bio-crude product yield and quality. The highest bio-crude and C4+ hydrocarbons yield was 46.5 wt % on a carbon basis. The optimal temperature range for RCFP is 450-475 degrees C; the biomass WHSV should be kept low, around 0.6 h(-1) in this reactor system, to produce a low oxygen content bio-crude (7.2 wt %), and improvements in the bio-crude yield and quality based on increased pressure are less significant beyond 2.7 bar. The product composition varies by at most 10% for up to 3.5 h' time on stream (biomass-to-catalyst ratio of 2.6 g g(-1)), indicating a stable catalyst activity for hydrodeoxygenation.
Study of Hydrodeoxygenation of Bio-Oil from the Fast Pyrolysis of Biomass

SP Zhang,YJ Yan,JW Ren,TC Li

DOI: https://doi.org/10.1080/00908310290142118

2003-01-01

Energy Sources

Abstract:The bio-oil obtained from the fast pyrolysis of biomass has a high oxygen content. Ketones and aldehydes, carboxylic acids and esters, aliphatic and aromatic alcohols, and ethers have been detected in significant quantities. Because of the reactivity of oxygenated groups, the main problems of the oil are instability. Therefore study of the deoxygenation of bio-oil is needed. In the present work the mechanism of hydrodeoxygenation (HDO) of bio-oil in the presence of a cobalt molybdate catalyst was studied. Particularly, the effects of reaction time, temperature, and hydrogen pressure on the HDO activity were examined. On the experimental results, a kinetic model for HDO of bio-oil was proposed.
Mechanistic Insights into Hydrodeoxygenation of Acetone over Mo/HZSM-5 Bifunctional Catalyst for the Production of Hydrocarbons

Kai Miao,Tan Li,Jing Su,Cong Wang,Kaige Wang

DOI: https://doi.org/10.3390/en15010053

IF: 3.2

2021-01-01

Energies

Abstract:Catalytic hydropyrolysis via the introduction of external hydrogen into catalytic pyrolysis process using hydrodeoxygenation catalysts is one of the major approaches of bio-oil upgrading. In this study, hydrodeoxygenation of acetone over Mo/HZSM-5 and HZSM-5 were investigated with focus on the influence of hydrogen pressure and catalyst deactivation. It is found that doped MoO3 could prolong the catalyst activity due to the suppression of coke formation. The influence of hydrogen pressure on catalytic HDO of acetone was further studied. Hydrogen pressure of 30 bar effectively prolonged catalyst activity while decreased the coke deposition over catalyst. The coke formation over the HZSM-5 and Mo/HZSM-5 under 30 bar hydrogen pressure decreased 66% and 83%, respectively, compared to that under atmospheric hydrogen pressure. Compared to the test with the HZSM-5, 35% higher yield of aliphatics and 60% lower coke were obtained from the Mo/HZSM-5 under 30 bar hydrogen pressure. Characterization of the spent Mo/HZSM-5 catalyst revealed the deactivation was mainly due to the carbon deposition blocking the micropores and Bronsted acid sites. Mo/HZSM-5 was proved to be potentially enhanced production of hydrocarbons.
Microwave pyrolysis of biomass for low-oxygen bio-oil: Mechanisms of CO2-assisted in-situ deoxygenation

Donghua Xu,Junhao Lin,Rui Ma,Lin Fang,Shichang Sun,Juan Luo

DOI: https://doi.org/10.1016/j.renene.2021.11.069

IF: 8.7

2022-01-01

Renewable Energy

Abstract:This work used CO2 as a co-reaction gas to realize in-situ deoxygenation of the bio-oil produced from microwave pyrolysis of biomass, and the mechanisms were thoroughly analyzed. Results showed that the bio-oil obtained at 550 °C (N2 atmosphere) had the highest yield of 29.24 wt% with the higher heating value (HHV) of 20.27 MJ/kg. The introduction of CO2 atmosphere reduced the oxygen content of the bio-oil by 12.68 wt% and increased the HHV by 26.43%. The oxygen mass balances demonstrated that the oil-O decreased by 31.45%, and the gas-O increased by 29.28% at CO2 atmosphere. The specific components in the bio-oil and pyrolytic gas were characterized. Furans in the bio-oil could react homogeneously with CO2 to generate CO at CO2 atmosphere, which was the main route to realize in-situ deoxygenation of the bio-oil. Meanwhile, stearic acid was selected as a model compound of the bio-oil to verify the action mechanisms of CO2 atmosphere. CO2 inhibited the decomposition of stearic acid to reduce the polycyclic aromatic hydrocarbons (PAHs) content in the bio-oil and promoted the generation of alkenes and CO. This study provides a novel perspective for the production of low-oxygen and high-quality bio-oil from biomass using CO2 reaction atmosphere.

energy & fuels,green & sustainable science & technology
Carbon‐Supported Molybdenum‐Based Catalysts for the Hydrodeoxygenation of Maize Oil

Yu Qin,Lili He,Jinzhao Duan,Ping Chen,Hui Lou,Xiaoming Zheng,Haiping Hong

DOI: https://doi.org/10.1002/cctc.201402035

IF: 4.5

2014-01-01

ChemCatChem

Abstract:The hydrodeoxygenation (HDO) of maize oil was performed in an autoclave with Mo‐based catalysts supported by different carbon materials, such as reduced graphene oxide, activated charcoal, graphite, and fullerene. Nanostructured Mo‐based catalysts with different phase compositions were prepared by using the carbothermal hydrogen reduction method at temperatures ranging from 500 to 700 °C and characterized by Raman spectroscopy, N2 adsorption isotherms, SEM, TEM, XRD, X‐ray photoelectron spectroscopy, and ammonia temperature‐programmed desorption. The highest total hydrocarbon yield of 90.32 % was obtained on the reduced graphene oxide‐supported molybdenum carbide catalyst at 700 °C. These results are subject to the complicated effect of different factors such as phase composition, defect concentration, and particle size on the catalytic behavior of the materials. Unique structures of different supports also play a significant role in the HDO reaction. On the basis of the results of comprehensive analysis of products and catalysts, an HDO mechanism was proposed. These Mo‐based catalysts are a promising system to prepare high‐quality diesel fuels from renewable resources.
Molybdenum-catalyzed Hydrogenolysis of Herbaceous Biomass: A Procedure Integrated Lignin Fragmentation and Components Fractionation

Xue Gong,Jiankui Sun,Xiangya Xu,Bo Wang,Helong Li,Feng Peng

DOI: https://doi.org/10.1016/j.biortech.2021.124977

IF: 11.4

2021-01-01

Bioresource Technology

Abstract:In this work, a low-cost MoO2/C catalyst was prepared for the reductive catalytic fractionation (RCF) of various herbaceous biomass feedstocks (Miscanthus, Triarrhena, Floridulus, Sorghum stem and Corncob). Phenolic monomers from the hydrogenolysis of lignin component were obtained in up to 26.4 wt%, with high selectivity towards methyl coumarate (33%) and methyl ferulate (24%). The RCF left solid carbohydrate pulps with high retentions (up to 87%), which were suitable for enzymatic hydrolysis. The reaction conditions, including temperature, time, H2 pressure, and sawdust size were examined in terms of monophenols yield, selectivity, delignification and sugar retention. This study showed that MoO2/C could function as an excellent catalyst for lignin fragmentation as well as the fractionation of herbaceous biomass components.
Guaiacol to Aromatics: Efficient Transformation over In Situ-Generated Molybdenum and Tungsten Oxides

Mariyam Mukhtarova,Maria Golubeva,Alexey Sadovnikov,Anton Maximov

DOI: https://doi.org/10.3390/catal13020263

IF: 3.9

2023-01-23

Catalysts

Abstract:The development of catalysts for the hydrodeoxygenation of bio-based feedstocks is an important step towards the production of fuels and chemicals from biomass. This paper describes in situ-generated bulk molybdenum and tungsten oxides in the hydrodeoxygenation of the lignin-derived compound guaiacol. The catalysts obtained were studied using powder X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, high-resolution transition electron microscopy, diffuse reflectance infrared Fourier transform spectroscopy, and Raman spectroscopy. The use of metal carbonyls as precursors was shown to promote the formation of amorphous molybdenum oxide and crystalline tungsten phosphide under hydrodeoxygenation conditions. The catalysts' activity was investigated under various reaction conditions (temperature, H2 pressure, solvent). MoOx was more active in the partial and full hydrodeoxygenation of guaiacol at temperatures of 200–380 °C (5 MPa H2, 6 h). However, cyclohexane, which is an undesirable product, was formed in significant amounts using MoOx (5 MPa H2, 6 h), while WOx was more selective to aromatics. When using dodecane as a solvent (380 °C, 5 MPa H2, 6 h), the benzene-toluene-xylenes fraction was obtained with a 96% yield over the WOx catalyst.

chemistry, physical
A Review of Recent Research on Catalytic Biomass Pyrolysis and Low-Pressure Hydropyrolysis

Andreas Eschenbacher,Paul Fennell,Anker Degn Jensen

DOI: https://doi.org/10.1021/acs.energyfuels.1c02793

2021-11-07

Abstract:Direct catalytic upgrading of biomass-derived fast pyrolysis vapors can occur in different process configurations, under either inert or hydrogen-containing atmospheres. This review summarizes the myriad of different catalysts studied and benchmarks their deoxygenation performance by also taking into account the resulting decrease in bio-oil yield compared to a thermal pyrolysis oil. Generally, catalyst modifications aim at improving the initial selectivity of the catalyst to more desirable oxygen-free hydrocarbons and/or improving the catalysts’ stability against deactivation by coking. Optimizing the pore structure and acid site density/distribution of solid acid catalysts can slow down deactivation and prolong activity. Basic catalysts such as MgO and Na2O/γ-Al2O3 are excellent ketonization catalysts favoring oxygen removal via decarboxylation, whereas solid acid catalysts such as zeolites primarily favor decarbonylation and dehydration. Basic catalysts can therefore produce bio-oils with higher H/C ratios. However, since their coke formation per surface area is higher, compared to a microporous HZSM-5 zeolite, precoking (or imperfect regeneration) of these basic catalysts and operating for longer time-on-stream can be approaches to improve the oil yield. In-line vapor-phase upgrading with a dual bed comprising a solid acid catalyst followed by a basic catalyst active in ketonization and aldol condensation further improves deoxygenation while maintaining high bio-oil carbon recovery. Also low-cost catalysts such as iron-rich red mud have deoxygenation activity. An improved bio-oil carbon recoverycompared at a similar level of oxygen removalcan be obtained when changing from an inert atmosphere to a hydrogen-containing atmosphere and using an effective hydrodeoxygenation (HDO) catalyst. To keep costs low, this can be conducted at near-atmospheric pressure conditions. Pt/TiO2 and MoO3/TiO2 showed high activity and reduced coke formation. Stable performance has been demonstrated using Pt/TiO2 for 100+ reaction/regeneration cycles with woody biomass feedstock. If future works can demonstrate the same durability for lower-cost biomass containing higher contents of ash, N, and S, this would considerably boost the commercial viability of near-atmospheric pressure HDO. Further research should be directed to testing the durability of lower-cost HDO catalysts such as MoO3/TiO2 and further improving the activity and stability of lower-cost catalysts.

energy & fuels,engineering, chemical
Facile synthesis of Pd@MOF catalyst and its application for High Selective Hydrogenation and Hydrodeoxygenation of Biomass-Derived Compounds

Jianguo liu,Xiuzhi Wei,Xinghua Zhang,Lungang Chen,Qi Zhang,Longlong Ma

DOI: https://doi.org/10.26434/chemrxiv-2022-47vqd

2022-01-01

Abstract:High selective hydrogenation and hydrodeoxygenation of biomass-derived compounds are still challenging especially under mild reaction conditions using heterogeneous catalysis. Here, we reported a one-step synthesis method that successfully prepared Pd species immobilized on NH2-MIL-125 (Ti) MOF frameworks which were named Pd@MOF and used as a highly efficient hydrodeoxygenation catalyst for the reduction of vanillin to 2-methoxy-4-methyl phenol in excellent yield with an atm of H2 pressure at room temperature. Pd(PPh3)4 was dispersed in a solvent containing the MOF precursors. Among them, the PPh3 ligand could be oxidized to remove and Pd particles in situ doped in MOF framework during the solvothermal process. Compare to immersed-Pd/MOF and Pd-MOF, Pd@MOF has higher catalytic efficiency because the smaller Pd particles encapsulated in MOF inhibit Pd over oxidation. Moreover, the different reduction products could be obtained selectively by tuning reaction time, and the catalyst realized to catalyze the highly effective transformation of a variety of biomass-derived compounds.
Deactivation of a CoMo Catalyst during Catalytic Hydropyrolysis of Biomass. Part 1. Product Distribution and Composition

M. Z. Stummann,M. Høj,A. B. Hansen,P. Beato,P. Wiwel,J. Gabrielsen,P. A. Jensen,A. D. Jensen

DOI: https://doi.org/10.1021/acs.energyfuels.9b02523

2019-11-14

Abstract:Deactivation of a sulfided CoMo/MgAl2O4 catalyst during fluid bed catalytic hydropyrolysis of biomass (beech wood) was studied. The stability of the catalyst was investigated by converting approximately 4.4 kg of biomass and collecting the liquid and solid products for every 1 kg fed, using the same catalyst load. The total time on stream was 16.2 h. A secondary hydrotreating reactor with a sulfided NiMo/Al2O3 catalyst was used after the fluid bed to further deoxygenate the vapors. The condensed organics and C4+ gases yield for each 1 kg fed was 22.2 ± 1 wt %, which was variations within the experimental uncertainty. The CO and CO2 yield during the experiment increased from 14.9 to 18.2 wt % daf, while the aqueous phase yield decreased from 38.0 to 35.1 wt % daf. The change in CO, CO2, and aqueous phase yields was ascribed to a decrease in hydrodeoxygenation activity of the used catalysts. The concentration of oxygen in the condensed organic phase increased from 40 to 2832 ppm, indicating that deactivation of the catalyst in both the fluid bed and the HDO reactor occurred. Our previous study (Stummann etal. Energy Fuels 2019, 33, 1302–1313.) has shown that potassium, a known catalyst poison, is transferred from the beech wood to the catalyst, and the effect of doping the catalyst with 1.9 wt % potassium was therefore also investigated. The results were compared to a similar experiment with a fresh catalyst. Both experiments were performed without the downstream hydrotreating reactor to show the effect on the chemistry in the fluid bed reactor only. This showed that potassium decreased the catalyst's cracking, hydrogenation, and hydrodeoxygenation activity. Doping the catalyst with potassium also increased the char and coke yield from 13.3 to 14.6 wt % daf, indicating that potassium can act as a catalyst for polymerization of the pyrolysis vapors. Overall, the results not only show promise for using CoMo based catalysts for catalytic hydropyrolysis but also indicate that attention should be paid to catalyst deactivation.

energy & fuels,engineering, chemical
Comparative Study of Fast Pyrolysis, Hydropyrolysis and Catalytic Hydropyrolysis of Poplar Sawdust and Rice Husk in a Modified Py-GC/MS Microreactor System: Insights into Product Distribution, Quantum Description and Reaction Mechanism

Yifeng He,Yingnan Zhao,Meiyun Chai,Zhongyue Zhou,Manobendro Sarker,Chong Li,Ronghou Liu,Junmeng Cai,Xinghua Liu

DOI: https://doi.org/10.1016/j.rser.2019.109604

2020-01-01

Abstract:Fast pyrolysis, hydropyrolysis and catalytic hydmpyrolysis are three important methods to produce bio-oil from biomass and are of great interest to researchers. In this research, the comprehensive study of pyrolysis, hydropyrolysis and catalytic hydmpyrolysis of poplar sawdust and rice husk was investigated in a modified laboratory Py-GC/MS microreactor system. Rh/ZrO2 (0.5 wt %) was prepared and applied in the catalytic hydropyrolysis process. An evaluation system including estimating method of product selectivity, the calculation method of O/C and H/C ratio, deoxygenation extent (DE) and hydrogen-loss extent (HLE), was established to fully measure the deoxygenation effect. The Rh/ZrO2-assisted catalytic hydropyrolysis showed a good deoxygenation effect as O/C ratios (0.10 for poplar sawdust, 0.11 for rice husk, respectively) are comparable to that of the reported upgraded bio-oil by hydrodeoxygenation (HDO). The highest hydrocarbon selectivity of 49.14% and DE of 87.6% were obtained in catalytic hydropyrolysis of poplar sawdust. For rice husk, the hydropyrolysis process gained a similar DE (82.7%) to that of the catalytic HyPy (83.7%), because rice husk with high ash content (19.4 wt %) contains a large number of mineral elements that are likely to form a self-catalysis effect. The reaction mechanism was further inferred according to product distribution and quantum calculation of oxygen-containing products, suggesting that Rh/ZrO2-assisted hydropyrolysis was accomplished by multistage reactions, involving initial pyrolysis of raw biomass and further deoxygenation of the pyrolysis intermediates. Moreover, this work can also provide a proven methodology and theoretical supports for future studies on catalytic hydropyrolysis of biomass.
Influence of Impregnation Processes on Ruthenium–Molybdenum Carbon Catalysts for Selective Hydrodeoxygenation of Biomass‐Derived Sorbitol into Renewable Alkanes

Yujing Weng,Tiejun Wang,Peigao Duan,Chenguang Wang,Feng Wang,Qiying Liu,Lungang Chen,Haiyong Wang,Zheng Liang,Longlong Ma

DOI: https://doi.org/10.1002/ente.201700885

IF: 4.149

2018-01-01

Energy Technology

Abstract:Sorbitol, as a C6 sugar related compound derived from cellulose, is regarded as a promising biomass-derived substrate and has characteristically higher oxygen content than in fossil-based resources. In this work, ruthenium-molybdenum carbon catalysts prepared by different impregnation processes were employed and extensively studied in a trickle-bed reactor for sorbitol hydrodeoxygenation (HDO). Interestingly, these catalysts afforded remarkably different HDO performance. Ruthenium-molybdenum catalysts prepared by ultrasonic treatment and calcination obtained high HDO performance in sorbitol conversion with 79.8% carbon yield of C5/C6 alkanes (pentane and hexane), almost twice that of ruthenium-molybdenum catalysts prepared without using a calcination processes. Therefore, a series of characterization studies (N-2-adsorption, XRD, HRTEM, XPS, H-2-TPR, CO-TPD, NH3-TPD, Py-IR spectra, etc.) were performed over relevant catalysts to study the catalytic mechanism. The results suggest that prior calcination offers a better chance for the proximity between Ru and Mo precursors to produce the bimetallic catalytic structure Ru-MoOx, which produces high HDO performance.
Ex-situ Catalytic Upgrading of Vapors from Microwave-Assisted Pyrolysis of Low-Density Polyethylene with MgO

Liangliang Fan,Yaning Zhang,Shiyu Liu,Nan Zhou,Paul Chen,Yuhuan Liu,Yunpu Wang,Peng,Yanling Cheng,Min Addy,Hanwu Lei,Roger Ruan

DOI: https://doi.org/10.1016/j.enconman.2017.07.039

IF: 11.4

2018-01-01

Bioresource Technology

Abstract:In-situ and ex-situ catalytic upgrading with HZSM-5 of vapors from microwave-assisted pyrolysis of lignin were studied. The in-situ process produced higher bio-oil and less char than ex-situ process. The gas yield was similar for both processes. The ex-situ process had higher selectivity to aromatics and produced more syngas and less CO2 than the in-situ process. Additional experiments on ex-situ process found that the bio-oil yield and coke deposition decreased while the gas yield increased at higher catalyst-to-lignin ratios and catalytic upgrading temperatures. The increased catalyst-to-lignin ratio from 0 to 0.3 reduced the selectivity of methoxy phenols from 73.7% to 22.6% while increased that of aromatics from 1.1% to 41.4%. The highest selectivity of alkyl phenols (31.9%) was obtained at 0.2 of catalyst-to-lignin ratio. Higher catalytic temperatures favored greater conversion of methoxy phenols to alkyl phenols and aromatics. Appropriate catalyst-to-lignin ratio (0.3) together with higher catalytic temperatures favored syngas formation.
Biomass Residues Purification: Elimination of Oxygen from Oxolane and its Monomethylated Derivatives through Hydrodeoxygenation Process

Simplice Koudjina,Naveen Kosar,Gaston A. Kpotin,Affi Sopi Sopi Thomas,Tariq Mahmood,Guy Y. S. Atohoun

DOI: https://doi.org/10.1088/1402-4896/ad2d4d

2024-02-27

Physica Scripta

Abstract:The persistent global demand for fossil fuels has spurred significant interest in the invention of new renewable energy sources to replace finite, non-renewable fossil fuel reserves. Among these sustainable energy options, biomass stands out as a promising candidate for producing environmentally friendly alternative fuels. However, the organic compounds found in biomass contain a high oxygen content, leading to several undesirable characteristics in biofuels, including low energy density, less stability, high viscosity, and corrosion. Consequently, researchers have devised various upgrading techniques, with a particular emphasis on the hydrodeoxygenation (HDO) process, to enhance the value of biofuels. In this research report, we investigated the treatment of Oxolane, 2-Methyloxolane and 3-Methyloxolane via adsorption and catalytic hydrogenolysis (HDL) processes. These processes aim to remove the oxygen heteroatom from these compounds, ultimately achieving the desired purity levels. To elucidate the underlying mechanisms, we employed the B3LYP/6-31G(d) and LanL2DZ/6-31G(d) methods of DFT for reaction without or with catalysts. The hydrogenolysis, in the presence and absence of a catalyst is carried at a temperature and pressure of 523 K and 40 bars, respectively. We meticulously analyzed the variations in geometries, thermodynamic and kinetic properties to gain insights into the whole processes. For each molecule, the sequence involves ring opening of C-O bonds, followed by the elimination of a water molecule. The first hydrogenolysis step yields an alcohol as a reaction intermediate, while the second hydrogenolysis step results in the formation of an alkane. All the reactions are exothermic in nature which confirmed the feasibility of these reactions. Geometric parameters show increased reactivity of Oxolane and its derivatives in the presence of tungsten disulphide (WS2) catalyst. Chemical potential indicates a charge transfer in all complexes maximum, and the highest charge transfer is observed in Oxolane in the presence of tungsten disulphide (WS2) catalyst.

physics, multidisciplinary
In situ hydrodeoxygenation of heavy bio-oil using a Ce/Fe-based oxygen carrier in methanol-zero valent aluminum media

Meiling Yang,Guozhang Chang,Weiwei Cui,Peng Ni,Qiujie Yi,Laishun Yang,Cuiping Wang

DOI: https://doi.org/10.1016/j.chemosphere.2024.141338

IF: 8.8

2024-02-07

Chemosphere

Abstract:Resource recovery from solid organic wastes, such as degradable plastics, and upgrading raw bio-oil are important ways for reducing carbon and pollution emissions. Hydrodeoxygenation (HDO) is a common thermochemical treatment to upgrade crude bio-oil. In this study, in order to realize in situ HDO during the hydropyrolysis of heavy bio-oil and degradable plastics, a reduced Fe/Ce oxygen carrier (OC) was used to catalytically remove oxygen from organics under the methanol-zero valent aluminum (ZV Al) media, where the hydrogen was produced during pyrolysis instead of a direct hydrogen supply. The results showed that the reduced OC captured the oxygen from the pyrolysis products of heavy bio-oil and degradable plastic, representing the multi-selectivity of reduced OC to phenols, ketones, etc. The ZV Al system promoted the production and utilization of hydrogen, as evidenced by the increased hydrogen content in gas phase and hydrocarbon content in liquid phase. The hydrocarbon component distribution in the liquid phase increased clearly when hydropyrolysis with degradable plastics addtion, but the excess degradable plastics addition caused increasing of the liquid product viscosity, and decreasing of the liquid products yield for the higher ash content in degradable plastic, and a higher ZV Al amount was required to maintain the hydropyrolysis. Molecular dynamics simulations verified the synergistic effect of degradable plastics and bio-oil by the pyrolysis behavior in different systems and temperatures, and the pyrolysis pathways were proposed. This non-autocatalytic system realized the resource recovery and heavy bio-oil upgrading using an Fe/Ce oxygen carrier.

environmental sciences
Direct Hydrodeoxygenation of Raw Woody Biomass into Liquid Alkanes

Qineng Xia,Zongjia Chen,Yi Shao,Xueqing Gong,Haifeng Wang,Xiaohui Liu,Stewart F. Parker,Xue Han,Sihai Yang,Yanqin Wang

DOI: https://doi.org/10.1038/ncomms11162

IF: 16.6

2016-01-01

Nature Communications

Abstract:Being the only sustainable source of organic carbon, biomass is playing an ever-increasingly important role in our energy landscape. The conversion of renewable lignocellulosic biomass into liquid fuels is particularly attractive but extremely challenging due to the inertness and complexity of lignocellulose. Here we describe the direct hydrodeoxygenation of raw woods into liquid alkanes with mass yields up to 28.1 wt% over a multifunctional Pt/NbOPO4 catalyst in cyclohexane. The superior performance of this catalyst allows simultaneous conversion of cellulose, hemicellulose and, more significantly, lignin fractions in the wood sawdust into hexane, pentane and alkylcyclohexanes, respectively. Investigation on the molecular mechanism reveals that a synergistic effect between Pt, NbOx species and acidic sites promotes this highly efficient hydrodeoxygenation of bulk lignocellulose. No chemical pretreatment of the raw woody biomass or separation is required for this one-pot process, which opens a general and energy-efficient route for converting raw lignocellulose into valuable alkanes.
Integration of Biomass Catalytic Pyrolysis and Methane Aromatization over Mo/HZSM-5 Catalysts

Zixu Yang,Ajay Kumar,Allen Apblett

DOI: https://doi.org/10.1016/j.jaap.2016.06.021

IF: 6

2016-01-01

Journal of Analytical and Applied Pyrolysis

Abstract:The development of an effective process to convert bio-oil into intermediate platforms that are compatible with the existing refinery infrastructure is highly needed. To overcome the high cost of hydrogen consumption in conventional bio-oil upgrading processes, this paper reports a novel process that converts three major biomass constituents (cellulose, hemicellulose and lignin) directly into liquid fuels via pyrolysis in the presence of methane over molybdenum impregnated HZSM-5 catalysts. The carbon yield of total aromatics from lignin increased from 12.80 to 15.13% when pyrolysis atmosphere switched from helium to methane in the presence of HZSM-5 support. However, methane was not effective in improving the aromatics yield from cellulose and hemicellulose in the presence of Mo-modified HZSM-5 catalysts. The molybdenum impregnated catalyst was found to promote deoxygenation of lignin-derived phenols. The carbon yield of polyaromatics from lignin was 5.47% in the presence of HZSM-5 support under methane, compared to 2.61% that obtained in the presence of Mo2C/HZSM-5. (C) 2016 Elsevier B.V. All rights reserved.
Catalytic HDO of pyrolysis oil in supercritical ethanol with CoMoP and CoMoW catalysts supported on different carbon materials using formic acid as in-situ hydrogen sources

Mingyuan Zhang,Haoyu Wang,Xue Han,Yimin Zeng,Chunbao Charles Xu

DOI: https://doi.org/10.1016/j.biombioe.2023.106814

IF: 5.774

2023-07-01

Biomass and Bioenergy

Abstract:The work investigated performances of several CoMoP and CoMoW catalysts supported on different carbon materials in catalytic hydrodeoxygenation (HDO) of pyrolysis oil in supercritical ethanol using formic acid as an in-situ hydrogen source. Among them, the CoMoP catalyst supported on ZnCl2 activated sawdust carbon (ASC-Zn) and the CoMoW catalyst supported on multi-walled carbon nanotubes (MWNTs) showed the best HDO performance at both 300 °C and 350 °C for 2 h, obtaining higher upgraded oil yield, lower oxygen contents of the upgraded oils, and higher degrees of deoxygenation (DOD). Whereas the stability tests with three HDO cycles showed that both catalysts were slightly deactivated likely by active metals leach-out or coke/carbon deposition on active sites of the catalysts.

energy & fuels,biotechnology & applied microbiology,agricultural engineering
Oxidant-assisted methane pyrolysis

Marco Gigantino,Henry Moise,Dimitri Saad,Jacob Fishman,Alexander Nelson,Harry Voorhis,Eddie Sun,Adam Brandt,Arun Majumdar,Matteo Cargnello

DOI: https://doi.org/10.26434/chemrxiv-2024-5mtf2

2024-11-14

Abstract:Methane pyrolysis has been proposed as a cost-competitive route to produce low CO₂ -emissions hydrogen that can utilize today’s infrastructure to supply feedstock and manage waste, and thereby be rapidly scalable. However, this process faces challenges such as catalyst deactivation and carbon build-up that hinder its large-scale implementation. Pyrolysis is usually conducted in the absence of oxidizers to avoid combustion products such as CO₂ . Here, however, we demonstrate that the addition of small concentrations of an oxidant to a methane pyrolysis reaction on Fe-based catalysts prevented catalyst deactivation and increased the net production of carbon and hydrogen. Methane pyrolysis in the presence of a small amount of CO₂ demonstrated a twofold increase in carbon yield and a 7.5-fold increase in hydrogen concentration in the effluent compared to that of a pure methane feed during 1 h operation in a fluidized bed reactor at 750 °C. A similar beneficial effect was observed by adding small amounts of H₂O in the feed. We provide evidence that the cyclic formation and decomposition of an iron carbide catalyst phase allowed for increased methane decomposition and significant carbon removal from the catalyst surface, thus increasing carbon and hydrogen yields. It was also shown that a similar result was obtained for Ni- and Co-based catalysts.

Chemistry

Ex Situ Hydrodeoxygenation in Biomass Pyrolysis Using Molybdenum Oxide and Low Pressure Hydrogen

In Situ Synthesis of Molybdenum Oxide@n-Doped Carbon from Biomass for Selective Vapor Phase Hydrodeoxygenation of Lignin-Derived Phenols under H2atmosphere

Reactive Catalytic Fast Pyrolysis of Biomass over Molybdenum Oxide Catalysts: A Parametric Study

Study of Hydrodeoxygenation of Bio-Oil from the Fast Pyrolysis of Biomass

Mechanistic Insights into Hydrodeoxygenation of Acetone over Mo/HZSM-5 Bifunctional Catalyst for the Production of Hydrocarbons

Microwave pyrolysis of biomass for low-oxygen bio-oil: Mechanisms of CO2-assisted in-situ deoxygenation

Carbon‐Supported Molybdenum‐Based Catalysts for the Hydrodeoxygenation of Maize Oil

Molybdenum-catalyzed Hydrogenolysis of Herbaceous Biomass: A Procedure Integrated Lignin Fragmentation and Components Fractionation

Guaiacol to Aromatics: Efficient Transformation over In Situ-Generated Molybdenum and Tungsten Oxides

A Review of Recent Research on Catalytic Biomass Pyrolysis and Low-Pressure Hydropyrolysis

Facile synthesis of Pd@MOF catalyst and its application for High Selective Hydrogenation and Hydrodeoxygenation of Biomass-Derived Compounds

Deactivation of a CoMo Catalyst during Catalytic Hydropyrolysis of Biomass. Part 1. Product Distribution and Composition

Comparative Study of Fast Pyrolysis, Hydropyrolysis and Catalytic Hydropyrolysis of Poplar Sawdust and Rice Husk in a Modified Py-GC/MS Microreactor System: Insights into Product Distribution, Quantum Description and Reaction Mechanism

Influence of Impregnation Processes on Ruthenium–Molybdenum Carbon Catalysts for Selective Hydrodeoxygenation of Biomass‐Derived Sorbitol into Renewable Alkanes

Ex-situ Catalytic Upgrading of Vapors from Microwave-Assisted Pyrolysis of Low-Density Polyethylene with MgO

Biomass Residues Purification: Elimination of Oxygen from Oxolane and its Monomethylated Derivatives through Hydrodeoxygenation Process

In situ hydrodeoxygenation of heavy bio-oil using a Ce/Fe-based oxygen carrier in methanol-zero valent aluminum media

Direct Hydrodeoxygenation of Raw Woody Biomass into Liquid Alkanes

Integration of Biomass Catalytic Pyrolysis and Methane Aromatization over Mo/HZSM-5 Catalysts

Catalytic HDO of pyrolysis oil in supercritical ethanol with CoMoP and CoMoW catalysts supported on different carbon materials using formic acid as in-situ hydrogen sources

Oxidant-assisted methane pyrolysis