Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Optimization of Fin Geometry of a Horizontal Low-Finned Condenser Tube.

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

A Numerical Investigation of Convective Condensation in Micro-Fin Tubes of Different Geometries

Convective Condensation Inside Horizontal Smooth and Microfin Tubes

Numerical Computation of Laminar Natural Convection Heat Transfer Around a Horizontal Compound Tube with External Longitudinal Fins

Fin Design for an Evaporator with Small Diameter Microgroove Tubes

Simulation Study on Fin-tube Condenser

Experimental Investigation of Condensation Heat Transfer on Hybrid Wettability Finned Tube with Large Amount of Noncondensable Gas

Fin design for fin-and-tube heat exchanger with microgroove small diameter tubes for air conditioner

Research on Structural Optimi zation fo Flat-tube Fins of an Ai r-cooler

Influence of condensate inundation on heat transfer of R134a condensing on three dimensional enhanced tubes and integral-fin tubes with high fin density

Acid Condensation and Heat Transfer Characteristics on H-type Fin Surface with Bleeding Dimples and Longitudinal Vortex Generators

Numerical and experimental investigation on the condensing heat transfer of R134a outside plain and integral-fin tubes

Experimental Investigation of Condensation in Micro-Fin Tubes of Different Geometries

Convective Heat Transfer and Pressure Drop of a Tube with Internal Longitudinal Fins

Numerical Study on the Heat Transfer and Pressure Drop Characteristics of Fin-and-tube Surface with Four Round-Convex Strips Around Each Tube

Condensation Pressure Drop and Heat Transfer in 5-Mm-od Micro-Fin Tubes

Airside Fin Efficiencies for Finned-Tube Heat Exchangers with Forced Convection

Experimental Study of the Air Side Performance of Fin-and-Tube Heat Exchanger with Different Fin Material in Dehumidifying Conditions

Three-Dimensional Numerical Simulation on the Laminar Flow and Heat Transfer in Four Basic Fins of Plate-Fin Heat Exchangers