Abstract:It is widely recognized that the scandium addition to aluminum alloys is an effective way to improve the comprehensive properties. To the present, researchers are concentrated on Al-Mg alloys, for multicomponent Al-Zn-Mg-Cu alloy, the microscopic characterization of the alloy heat treatment has gained a high level of research interest. However, researches on the evolution of precipitate microstructure in controlled plastic deformation combined with the role played by Sc have received scant attention. In the present paper, a micro-alloyed Al-Zn-Mg-Cu-Sc-Zr alloy was prepared by adding 0.2% scandium. Based on mastering the two-stage homogenization treatment in the early stage, the alloy was subjected to equal channel angular extrusion deformation, and subsequently the microstructure, dislocation evolution and precipitation behavior were observed. It is revealed that after second pass deformation, the grains in the deformation-prone zone are obviously shortened by 31% on average along the cross-section direction, compared with the first pass. Following two passes deformation, Al 3 (Sc, Zr), Al 3 Zr and MgZn 2Â phases are formed within grains, inhibiting grain coarsening and recrystallization during deformation. With the introduction of plastic deformation, it is analyzed that the shadow lines with different depths and stacking faults with different structures in the interior of the phase. Also, the overall proportion of the recrystallized structure and substructure of the alloy increases with the increasing deformation. In addition, after secondary deformation, the scandium rich compounds at the trigeminal grain boundary are reduced, while the zirconium rich compounds are significantly increased. Therefore, the different diffusivity of Sc/Zr elements and the combined effect of controlled thermal deformation can be considered to prepare the Al 3 Sc (Al 3 Zr) with core-shell structure in the later stage.

Effect of Sc and Zr Additions on Grain Stability and Superplasticity of the Simple Thermal–mechanical Processed Al–Zn–Mg Alloy Sheet

Superplastic Behavior and Microstructure Evolution of A New Al-Mg-Sc-Zr Alloy Subjected to A Simple Thermomechanical Processing

Achieving High Superplasticity of a New Al–Mg–Sc–Zr Alloy Sheet Prepared by a Simple Thermal–mechanical Process

Excellent superplasticity and deformation mechanism of Al–Mg–Sc–Zr alloy processed via simple free forging

Superplasticity Behaviors of Al-Zn-Mg-Zr Cold-Rolled Alloy Sheet with Minor Sc Addition

Achieving high superplasticity of a traditional thermal–mechanical processed non-superplastic Al–Zn–Mg alloy sheet by low Sc additions

High Strain Rate Superplasticity in an Al–Mg–Sc–Zr Alloy Processed Via Simple Rolling

Effect of Sc and Er Additions on Superplastic Ductilities in Al-Mg-Mn-Zr Alloy

Excellent High Strain Rate Superplasticity of Al-Mg-Sc-Zr Alloy Sheet Produced by an Improved Asymmetrical Rolling Process

Plastic Deformation and Precipitation Characterization of Al-Zn-Mg-Cu Alloy Micro-Alloyed with Sc

Dynamic Recrystallization-Dependent High-Temperature Tensile Properties and Deformation Mechanisms in Al-Mg-Sc-Zr Alloys

Effects of Zr/(Sc+Zr) Microalloying on Dynamic Recrystallization, Dislocation Density and Hot Workability of Al−Mg Alloys During Hot Compression Deformation

Superplasticity of 5083 Alloys with Zr and Mn Additions Produced by Reciprocating Extrusion

Effect of minor Sc and Zr on recrystallization behavior and mechanical properties of novel Al–Zn–Mg–Cu alloys

Microstructures and Mechanical Properties of a Novel Al-5Mg-3Zn Alloy with the Combined Additions Sc and Zr

Effect of Minor Sc and Zr Addition on Microstructure and Properties of Ultra-High Strength Aluminum Alloy

Effects of Sc and Zr on the Texture and Mechanical Anisotropy of High Strength Al–Zn–Mg Alloy Sheets

Microstructures and Mechanical Properties of Al-Mg and Al-Zn-Mg Based Alloys Containing Minor Scandium and Zirconium

Microstructures and Properties of Al–Zn–Mg–Mn Alloy with Trace Amounts of Sc and Zr

Nano-structure Evolution of Secondary Al3(Sc1−xZrx) Particles During Superplastic Deformation and Their Effects on Deformation Mechanism in Al-Zn-Mg Alloys

Effect of Minor Scandium Addition on Microstructures and Tensile Properties of Super-High Strength Al-Zn-Cu-Mg-Zr Alloys