Abstract:Based on theoretical calculations, laboratory simulation research and industrial production data analysis combined with characterisations such as metallographic microscope, scanning electron microscope (SEM), transmission electron microscope (TEM) and microhardness testing, this study investigated the state of occurrence and the precipitation law of vanadium (V) in microalloyed steel to determine a reasonable production process for V microalloyed steel. The results showed that the V(C,N) precipitation phase was the main form of V in microalloyed steel that precipitated after the transformation of austenite to ferrite. The amount of V precipitation was positively correlated with the amount of V that was added. However, the precipitation temperature was not significantly correlated with the amount added. When the V content increased from 0.03% to 0.06%, the initial precipitation temperature only increased by 23 °C. The coiling temperature was identified as the core factor affecting the strength of V microalloyed steel. When the effects of precipitation strengthening and microstructure strengthening were considered, as the coiling temperature decreased, the strength first increased, then decreased and finally increased again. Under different processing conditions, the strengthening of vanadium in the material increased first and then decreased as the temperature decreased (700–200 °C). The corresponding temperatures for the best strengthening effect of aging treatment, industrial statistical data and simulating coiling were 550, 470 and 400 °C, respectively. The difference between laboratory research results and industrial production was found. When V precipitation strengthening was used to improve material properties, it was necessary to determine a reasonable quantity of V to add and the production process, according to different alloy systems, to make more effective use of V microalloyed resources.

Precipitation Characteristics During Isothermal Γ to Α Transformation and Resultant Hardness in Low Carbon Vanadium–titanium Bearing Steel

Precipitation Behavior and Aging Hardening of Vanadium Alloys

Influence of V on the Microstructure and Precipitation Behavior of High-Carbon Hardline Steel during Continuous Cooling

Effect of Tungsten Addition on Continuous Cooling Transformation and Precipitation Behavior of a High Titanium Microalloyed Steel

Effect of isothermal holding temperature on the precipitation hardening in Vanadium-microalloyed steels with varying carbon and nitrogen levels

MICROSTRUCTURE, MECHANICAL PROPERTIES AND INTERPHASE PRECIPITATION BEHAVIORS IN V-Ti MICROALLOYED STEEL

Thermomechanical Control of Microstructure and Precipitation in Vanadium Microalloyed Steel: Influence of Finish Rolling and Coiling Temperatures

Effect of V on the Precipitation Behavior of Ti−Mo Microalloyed High-Strength Steel

Microstructure and Hardness Evolution During Isothermal Process at 700 °C for Fe–24Mn–0.7Si–1.0Al TWIP Steel

Hardening Through an Ultrafine Carbide Precipitation in Austenite of a Low-Carbon Steel Containing Titanium and Tungsten

Effects of Cooling Rate and Vanadium on δ→γ Phase Transformation in Low Carbon Steel

Precipitation Law of Vanadium in Microalloyed Steel and Its Performance Influencing Factors

Effect of carbide precipitation behavior at high temperatures on microstructure and mechanical properties of M50 steel

Interphase precipitation behavior of nano-sized carbides in low carbon steel

Analysis of the Extent of Interphase Precipitation in V-HSLA Steels Through In-Situ Characterization of the Γ/α Transformation

Randomization of Ferrite/austenite Orientation Relationship and Resultant Hardness Increment by Nitrogen Addition in Vanadium-microalloyed Low Carbon Steels Strengthened by Interphase Precipitation

Influence of Elevated Temperature Holding Time on Microstructure and Properties in Heat Affected Zone of Fine Grained Titanium Alloy

Discontinuous Precipitation During Isothermal Transformation in a 9–12% Chromium Ferritic Steel

Complex isothermal precipitation behavior of V(C, N) in V-, N-added low carbon steel

Influence of Isothermal Treatments on Microstructures and Hardness in 30mnvs Steel

Carbide Precipitation in Austenite of a Titanium-Tungsten-Bearing Low-Carbon Steel