Abstract:In this paper, a novel hard nickel composite coatings were fabricated by wide-band laser cladding technique. The effects of Si alloying on the composite coatings were investigated by microstructure characterization, phase identification, microhardness and wear resistance. Results showed that the in-situ precipitated phases in the laser molten pool were composed of the γ-Ni solid solution and hard phases such as Cr 23 C 6 , CrSi, Cr 5 B 3 . With the increase of Si element, the morphology of the precipitated phases changed significantly. When the added content of Si was 1.0 wt.%, the precipitated phase was a mainly block morphology. As the added content of Si was increased to more than 2.0 wt.%, the main precipitated phase was transformed into a long stripe morphology. With the increase of Si content, the stripe-like precipitated phase was gradually refined and finally becomes density needle-like precipitates. Element distribution analysis showed that the block precipitated phase was enriched in Cr, W and Si elements. Additionally, the enriched elements in the long strip precipitation phase were essentially the same as those in the block precipitation phase. The added Si element was highly involved in the in-situ reactions of precipitated phase. The TEM results showed that the precipitated phases contained the crystal structures of Cr 5 B 3 and Cr 7 C 3 . The pin-on-disc wear tests revealed that the composite coating with the addition of 6 wt.% Si exhibited the best wear resistance in the experimental group. The average friction coefficient was about 0.6 and the wear mass loss rate was about 2.38 × 10 −5 g/m under counter-abrasive conditions. The worn surface analysis indicated that the wear mechanism of composite coatings was mainly abrasive wear. The refined needle-like precipitated phase was closely bound to the matrix and thus not easy to peel off, providing a significant improvement in the wear resistance of the laser cladding coatings.

Wettability and Biomineralisation of Laser Cladded Si Doped TiCN Biocoating

Cladding Bio-Ceramic Coatings of Low SiO2-HA on the Surface of Titanium Alloy

Influence of Si Content on Microstructure and Mechanical Properties of TiAlSiN Nanocomposite Coatings

Laser surface modification for synthesis of textured bioactive and biocompatible Ca–P coatings on Ti–6Al–4V

Wetting effects on in vitro bioactivity and in vitro biocompatibility of laser micro-textured Ca-P coating.

Laser pulse dependent micro textured calcium phosphate coatings for improved wettability and cell compatibility

Tribological and Biological Behaviors of Laser Cladded Ti-based Metallic Glass Composite Coatings

Microstructure, Wear and Oxidation Resistance of Al-doped Ti–Si3N4 Coatings by Laser Cladding

Study on Microstructure, Microhardness, Bioactivity, and Biocompatibility of La2 O3 -Containing Bioceramic Coating Doping SiO2 Fabricated by Laser Cladding.

Osteoblast interaction with laser cladded HA and SiO 2-HA coatings on Ti-6Al-4V

Microstructure and wear properties of TiCN/Ti coatings on titanium alloy by laser cladding

Influence of Si on tribological behavior of laser cladded Fe-based amorphous/crystalline composite coatings

Microstructure and Wear Behaviours of Laser-Clad Cr13Ni5Si2-based Metal-Silicide Coatings on a Titanium Alloy

Effect of Na2O and ZnO on the microstructure and properties of laser cladding derived CaO-SiO2 ceramic coatings on titanium alloys

Evading stability-biocompatibility tradeoff in TiNb coatings with armour-like super hydrophilic micro-nano structure surface

Evaluation of microstructure, mechanical properties and osseointegration capacity of laser cladding β-type TiNbZr coatings

Fabrication and Microstructure of Catio3 Coating by Laser Cladding

Bio-corrosion behavior, antibacterial property and interaction with osteoblast of laser in-situ fabricated Ti-Si-Cu coatings on Ti-6Al-4V alloy

<i>In vitro</i> bio-tribological behaviour of textured nitride coating on selective laser melted Ti-6Al-4V alloy

Investigation on the Microstructure Evolution and Properties of a Novel In-Situ Fiber Phase-Reinforced Nickel Composite Coating Deposited by Wide-Band Laser

In-situ Synthesized TiC/TiB Ceramic Particle Composite Coating by Laser Cladding on TC4 Titanium Alloy