Abstract:Background: Fe80B20 amorphous alloys exhibit excellent soft magnetic properties, high abrasive resistance and outstanding corrosion resistance. In this work, Fe80B20 amorphous micro-fibers with HC of 3.33 Oe were firstly fabricated and the effects of annealing temperature on the structure and magnetic properties of the fibers were investigated. Methods: In this study, Fe80B20 amorphous fibers were prepared by the single roller melt-spinning method. The structures of as-spun and annealed fibers were investigated by X-ray diffractometer (XRD) (PANalytical X,Pert Power) using Cu Kα radiation. The morphology of the fibers was observed by scanning electron microscopy (SEM) (HITACHI-S4800). Differential scanning calorimetry (DSC) measurements of the fibers were performed on Mettler Toledo TGA/DSC1 device under N2 protection. Vibrating sample magnetometer (VSM, Versalab) was used to examine the magnetic properties of the fibers. The resonance behavior of the fibers was characterized by an impedance analyzer (Agilent 4294A) with a home-made copper coil. Results: The X-ray diffusion (XRD) patterns show that the fibers remain amorphous structure until the annealing temperature reaches 500°C. The differential scanning calorimetry (DSC) results show that the crystallization temperature of the fibers is 449°C. The crystallization activation energy is calculated to be 221 kJ/mol using Kissinger formula. The scanning electron microscopy (SEM) images show that a few dendrites appear at the fiber surface after annealing. The result indicates that the coercivity HC (//) and HC (⊥) slightly increases with increasing annealing temperature until 400°C, and then dramatically increases with further increasing annealing temperature which is due to significant increase in magneto-crystalline anisotropy and magneto-elastic anisotropy. The Q value firstly increases slightly when the annealing temperature rises from room temperature (RT) to 300°C, then decreases until 400°C. Eventually, the value of Q increases to ~2000 at annealing temperature of 500°C. Conclusions: In this study, Fe80B20 amorphous fibers with the diameter of 60 μm were prepared by the single roller melt-spinning method and annealed at 200°C, 300°C, 400°C, and 500°C, respectively. XRD results indicate that the fiber structure remains amorphous when the annealing temperature is below 400°C. α-Fe phase and Fe3B phase appear when the annealing temperature rises to 500°C, which is above the crystallization temperature of 449°C. The recrystallization activation energy is calculated to be 221 kJ/mol. The coercivity increases with increasing annealing temperature, which attributes to the increase of total anisotropy. All the as-spun and annealed fibers exhibit good resonance behavior for magnetostrictive sensors.

Bi-Based Superconducting Fibers Prepared from Amorphous Materials

Preparation, Structure and Properties of Bi-based Superconducting Fibers Grown by Laser-Floating-zone-growth Method

BI(PB)SRCACUO SUPERCONDUCTING FIBERS WITHOUT POSTGROWTH HEAT-TREATMENT

Fabrication, Characterization And Welding Of Bi(Pb)-Sr-Ca-Cu-O Superconducting Fibers

Preparation of the Bi-Sr-Ca-Cu-O Superconducting Fibers

110K Superconducting Fibers of [Bi,Pb(Sb)]2Sr2Ca2Cu2O10 + x

110K Superconducting Fibers of [Bi,Pb(Sb)]<sub>2</sub>Sr<sub>2</sub>Ca<sub>2</sub>Cu<sub>2</sub>O<sub>10 + x</sub>

Superlattice Structures Based on Amorphous Carbon

Fabrication and Superconducting Properties of MgB2 Wires with Amorphous Carbon Doping by In-situ Powder-in-tube Method

Superconducting Properties of Granular Smfeaso1-Xfx Wires with T-C=52 K Prepared by the Powder-In-Tube Method

Superconducting fiber with transition temperature up to 7.43 K in Nb2PdxS5-delta (0< x <0.6)

Preparation of FeCuNbSiB Fe-Based Amorphous Fibers and Its Properties After Annealing

Low-temperature synthesis of SmFeAsO0.7F0.3 wires with high transport critical current density

Superconductivity of Li doped BSCCO mesoscopic fiber

Superconducting Fiber with Transition Temperature Up to 7.43 K in Nb2PdxS5-δ (0.6 < X <1).

Superconducting Bipbsrcacuo Wires Grown on Metal Cores by A Melt Method

Phase formation and transport properties of vapor-solid reacted AIMI MgB2 superconductors

Preparation, Magnetic and Mechanical Properties of Fe/Ni-Based Amorphous Fibers

Effects of annealing on the structure and magnetic properties of Fe80B20 magnetostrictive fibers

Comparative study on the critical current performance of Bi-2223/Ag and YBCO wires in low magnetic fields at liquid nitrogen temperature

Electric-field induced strange metal states and possible high-temperature superconductivity in hydrogenated graphitic fibers