Abstract:Abstract Hundreds of millions of Air conditioning (AC) systems are produced each year. Many of them, especially small AC appliances, use rotary compressors as the system’s heat pump due to their simple structure and high efficiency in a small system. Lubricant oil is used in the rotary compressor to lubricate the moving parts, such as the crankshaft and the rolling piston, and to seal the clearance between the sliding parts, e.g., the clearance between the rolling piston and the cylinder, and the vane and the cylinder. As the compressed refrigerant vapor is discharged from the cylinder through the discharge port, part of lubricant oil in the cylinder would be carried by the vapor and atomize into small droplets in the lower cavity during the discharge process, which is complicated and highly-coupled. Some of these oil droplets would ultimately be exhausted from the compressor and enter other parts in the system, reducing the compressor reliability and deteriorating the heat transfer of the condenser and the evaporator in the system. Our previous research studied the atomization of the lubricant oil during the discharge process in the compressor’s lower cavity. However, the oil droplets’ behavior downstream of the lower cavity is unknown. Thus, studying the oil droplets’ behavior after passing through the rotor/stator can help understand how the rotor/stator would affect the droplet size distribution and movement, thus controlling the flow rate of escaped oil droplets. In this study, a hot gas bypass test rig is built to run a modified rotary compressor with sapphire windows right above the rotor/stator. The oil droplets’ size distribution and movement along the radial direction are obtained at the shaft’s rotating frequency of 30 and 60 Hz by shadowgraph. It is found that droplet size at 30 and 60 Hz varies little in the inner region of the rotor/stator clearance and would increase sharply above the clearance and keep increasing in the outer region of the clearance. More importantly, droplet velocity has a downward velocity component at the inner region and an upward velocity component at the outer region of the rotor/stator clearance. With the result of droplet size distribution and droplet velocity above the rotor/stator, we propose the model of the oil droplet’s path above the rotor/stator, which can be understood as the coupling of a swirling jet and a rotating disk.

A Cfd Model for the Oil Discharge Ratio in Rotary Compressors

Numerical study on oil supply system of a rotary compressor

CFD Simulation for the Internal Pressure Characteristics of an Oil-Injected Twin-Screw Refrigeration Compressor

Experimental Measurement of Oil Droplets Size and Velocity Above the Rotor/Stator in a Rotary Compressor

Experimental study of the lubricant-refrigerant flow in a rotary compressor

Modelling the Cylinder Cooling in an Oil-free Reciprocating Air Compressor

CFD Simulation of a Rotary Compressor with Gas Injection

Application of computational fluid dynamics (CFD) to ozone contactor optimization

Fluid-structure interaction analysis and optimization study of suction valves in small refrigeration compressors

Analysis of the oil supply system of a high-pressure shell scroll compressor

Computational Fluid Dynamics Analysis on Oil Pumping System for Rolling Piston Compressors

The Performance Analysis of R32 Rotary Compressor Used for Room Air Conditioners

Bleed air CFD modelling in aerodynamic simulation of A heavy duty gas turbine compressor

CFD Simulation and Experimental Study of Working Process of Screw Refrigeration Compressor with R134a

In-situ characterization of the size distribution of lubricant droplets in rotary compressor

Investigation of Separation Efficiency in Centrifugal Oil-Air Separator Based on CFD

Simulation on two-phase refrigerant compression in the cylinder of rotary compressors using CFD method

A Study on an Online Measurement Method to Determine the Oil Discharge Ratio by Utilizing Coriolis Mass Flow Meter in a Calorimeter

3D Transient Numerical Simulation of a Helical Roots Air Compressor for FCVs

The Computer Simulation of Oil--Flooded Refrigeration Twin-Screw Compressors

Experimental Analysis on R290 Solubility and R290/oil Mixture Viscosity in Oil Sump of the Rotary Compressor