Abstract:Abstract To enhance interfacial bonding between carbon fibers and epoxy matrix, the carbon fibers have been modified with multiwall carbon nanotubes (MWCNTs) using the dip- coating technique. FT-IR spectrum of the MWCNTs shows a peak at 1640 cm −1 corresponding to the stretching mode of the C=C double bond which forms the framework of the carbon nanotube sidewall. The broad peak at 3430 cm −1 is due to O–H stretching vibration of hydroxyl groups and the peak at 1712 cm −1 corresponds to the carboxylic (C=O) group attached to the carbon fiber. The peaks at 2927 cm −1 and 2862 cm −1 are assigned to C–H stretching vibration of epoxy produced at the defect sites of acid-oxidized carbon fiber surface. SEM image shows a better interface bonding between the fiber and the matrix of modified composites (MWCNTs-CF/Ep) than those of unmodified composite. The loss factor curve of CF-MWCNTs/Ep composites is the narrowest compared with neat epoxy and CF/Ep composites which evinces that the length distribution range of molecular chain segments in the matrix is the narrowest. From the dependence of the AC conductivity on temperature, we can see that σ AC increases when temperature increases. The increase in electrical conductivity of the composites may be a result of the increased chain ordering due to annealing effect. The use of MWCNTs to modify the surface of carbon fiber resulted in a large amount of junctions among MWCNT causing an increase in the electrical and thermal conductivity by forming conducting paths in the matrix. The MWCNTs-CF/Ep composite shows better thermal stability than unmodified composites. The strong interaction between CF and MWCNTs can retard diffusion of small molecules from the resin matrix at high temperature and hence, result in the improved thermal stability of the modified CF/Ep composite.

Thermal Conductivity of MWCNT/epoxy Composites: the Effects of Length, Alignment and Functionalization

Fabrication of Three-dimensional Thermally Conductive Carbon Fibers/Carbon Nanotubes Network Reinforce Epoxy Composites

Length-dependent Electrical and Thermal Properties of Carbon Nanotube-Loaded Epoxy Nanocomposites

High thermal conductivity of carbon nanotube sheet / epoxy composite

Improved Thermal Conductivity of Epoxy Composites Prepared with A Mixed Filler of Multiwalled Carbon Nanotubes and Aluminum Nitride Particles

Thermal Conductivity of EP/GNs/MWCNTs Composites

Contact Thermal Resistance Between Individual Multi-Wall Carbon Nanotubes

Effect of CNT Arrays on Electrical and Thermal Conductivity of Epoxy Resins

Electrical and thermal characteristics of MWCNTs modified carbon fiber/epoxy composite films

Effects of Carbon Nanotubes on Char Structure and Heat Transfer in Ethylene Propylene Diene Monomer Composites at High Temperature

Preparation and properties of MWCNTs-BNNSs/epoxy composites with high thermal conductivity and low dielectric loss

The effects of carbon nanotubes on electroactive shape-memory behaviors of hydro-epoxy/carbon black composite

Comparative characterization of multiscale carbon fiber composite with long and short MWCNTs at higher weight fractions

The Specific Heat and Effective Thermal Conductivity of Composites Containing Single-Wall and Multi-Wall Carbon Nanotubes.

Thermal Conductivity of Aligned CNT/polymer Composites Using Mesoscopic Simulation

Experimental Study on Thermal Conduction Performance of CNTs Materials

Fabrication and properties of aligned multiwalled carbon nanotube-reinforced epoxy composites

Characterization of Electrical Conductivity of Carbon Nanotube Composites

Carbon nanotubes grafting aminated epoxy resin with improved elasticity and surface adhesion for enhanced thermal management performance

Carbon Nanotube/Cu Nanowires/Epoxy Composite Mats with Improved Thermal and Electrical Conductivity

Review on Molecular Dynamics Simulations of Effects of Carbon Nanotubes (CNTs) on Electrical and Thermal Conductivities of CNT-Modified Polymeric Composites