Abstract:Current lithium‐ion batteries are predicted to be unable to provide the specific energy required to meet the ever‐increasing demands of rapidly emerging technologies. Due to a high theoretical specific capacity of 1675 mAh/g, sulfur has gained much attention as a promising positive electrode material for high specific energy rechargeable batteries. Although the lithium/sulfur cell has been studied for many years and continues to receive much attention today as an alternative power source for zero‐emission vehicles and advanced electronic devices, the realization of this novel cell's promise as a commercial product has yet to be successful. The major problems with sulfur electrodes involve: (1) the dissolution of sulfur (as polysulfides) and the resulting diffusion of dissolved polysulfides and (2) the deposition of insulating products (including Li2S) on both the negative and the positive electrodes. These solid deposits can physically block the electrode reaction sites, thus passivating the electrode surfaces. Another important problem is the large volume change that occurs with the conversion of S to Li2S. It is important to understand that the performance of Li/S cells is hampered by linked chemical and mechanical degradations and both degradation mechanisms must be correctly alleviated in order to markedly improve current‐technology Li/S cells. In this study, improved cycling performance via the reactive functional groups on graphene oxide to successfully immobilize sulfur and lithium polysulfides during operation has been demonstrated. The use of a new electrolyte and binder leads to improved cell performance in terms of high‐rate capability (up to at least 2 C) and good reversibility (S ↔ Li2S), yielding at least 800 cycles have also been demonstrated. © 2015 American Institute of Chemical Engineers AIChE J, 61: 2749–2756, 2015

How to Obtain Reproducible Results for Lithium Sulfur Batteries?

Nanostructured Β-Li3ps4 for All-Solid Lithium-Sulfur Batteries

A Novel Strategy for High-Stability Lithium Sulfur Batteries by in Situ Formation of Polysulfide Adsorptive-Blocking Layer

Controlled Nucleation and Growth Process of Li2S2/Li2S in Lithium-Sulfur Batteries

Controlled Nucleation and Growth Process of Li<sub>2</sub>S<sub>2</sub>/Li<sub>2</sub>S in Lithium-Sulfur Batteries

Insight into sulfur reactions in Li-S batteries.

Stable Cycling of Lithium Sulfide Cathodes Through Strong Affinity with A Bifunctional Binder

Electrochemical deposition of Li2S2/Li2S in aprotic Li–S batteries

Early Failure of Lithium–Sulfur Batteries at Practical Conditions: Crosstalk between Sulfur Cathode and Lithium Anode

Routes to Electrochemically Stable Sulfur Cathodes for Practical Li–S Batteries

Enabling High Energy Density Cathode for Lithium-Sulfur Batteries.

Revealing the Sulfur Redox Paths in a Li–S Battery by an In Situ Hyphenated Technique of Electrochemistry and Mass Spectrometry

Promoted Rate and Cycling Capability of Li–S Batteries Enabled by Targeted Selection of Co-Solvent for the Electrolyte

Effects of Cell Construction Parameters on the Performance of Lithium/Sulfur Cells

Improved Lithium–sulfur Batteries with a Conductive Coating on the Separator to Prevent the Accumulation of Inactive S-related Species at the Cathode–separator Interface

Electrolytes with Controlled Polysulfide Insolvability for Lithium-Sulfur Batteries

Lithium Sulfur Batteries with Compatible Electrolyte Both for Stable Cathode and Dendrite-Free Anode

Self-Discharge Behavior of Lithium-Sulfur Batteries at Different Electrolyte/Sulfur Ratios

(Invited) Functional Gradient Carbon-Sulfur Cathode for Rechargeable Li-S Battery

Manipulating Electrolyte and Solid Electrolyte Interphase to Enable Safe and Efficient Li-S Batteries

Simple Framework for Simultaneous Analysis of Both Electrodes in Stoichiometric Lithium-Sulfur Batteries