Abstract:The material flow behavior during friction stir welding (FSW) plays a critical role in the quality of final joints. In this study, the FSW of LAZ931 duplex Mg alloy was carried out at a rotation speed of 800 rpm and welding speeds of 50, 100, and 200 mm/min, respectively. A thin pure Mg strip inserted at the interface between the two Mg-Li alloy plates was used as a marker to study the flow behavior of the materials in the FSW process. Sound welds with no defects were obtained for all three welding speeds. The microstructural evaluations along the marker on the horizontal cross-section around the keyhole of the welds were characterized. As the welding speed increased, the marker came closer to the keyhole, indicating the decreased extent of the plastic deformation of the material. In the shoulder-affected zone (SAZ), the thickness of the marker reduced gradually in the accelerating stage and finally accumulated together in the decelerating stage. However, in the pin-affected zone (PAZ), the thickness of the marker reduced sharply in the accelerating stage and then became dispersed in the decelerating stage, and the degree of dispersion decreased as the weld speed increased. As a result, an elongated grain structure was formed in the SAZ, while two equiaxial grain structures were formed in the PAZ. The material on the advancing side was refined by the pin and deposited in the weld to form a fine equiaxial grain structure due to the high strain rate. In contrast, the material on the retreating side was pushed by the pin and thus directly deposited in the weld to form a coarse equiaxial grain structure. In addition, the area of the fine equiaxial grain structure was reduced obviously with the increase in welding speed.

Grain Structure Formation Ahead of Tool during Friction Stir Welding of AZ31 Magnesium Alloy

Microstructure Evolution During Friction-Stir Welding of AZ31 Magnesium Alloy

Microstructural Evolution Characterization of Friction Stirring Welded Az31 Magnesium Alloy

Microstructures evolution mechanism of friction stir welded AZ31 magnesium alloy

The Evolution of Grain Microstructure in Friction Stir Welding of Dissimilar Al/Mg Alloys with Ultrasonic Assistance

Effect of Welding Speed on the Material Flow Patterns in Friction Stir Welding of Az31 Magnesium Alloy

Effect of Tool Speed on Microstructure Evolution and Mechanical Properties of Friction Stir Welded Joints of Al-Mg-Si Alloy with High Cu Content

Macrostructure, Microstructure and Mechanical Properties of Bobbin Tool Friction Stir Welded ZK60 Mg Alloy Joints

Microstructural evolution and its effect on Hall-Petch relationship in friction stir welding of thixomolded Mg alloy AZ91D

Microstructure evolution during friction stir welding of 2024 aluminum alloy

Numerical simulation and experimental investigation on friction stir welding of AZ31 magnesium alloy

Microstructure Evolution and Strengthening Mechanism of Friction Stir Welded Joint of 20 Mm-Thick AZ31 Magnesium Alloy

Forming Process Analysis of Equiaxed Grain in Weld Nugget Zone During Friction-Stir Welding of Aluminum Alloy

Development of grain structure during friction-stir welding of Cu–30Zn brass

Material Flow and Microstructural Evolution in Friction Stir Welding of LAZ931 Duplex Mg-Li Alloys

Effect of rotation speed on microstructure and mechanical properties of bobbin tool friction stir welded AZ61 magnesium alloy

Texture Development During Friction Stir Welding of Magnesium Alloys

Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Grain Structure Development During Friction Stir Welding of Single-Crystal Austenitic Stainless Steel

Effect of Stacking Fault Energy on the Grain Structure Evolution of FCC Metals During Friction Stir Welding

Improving microstructural and mechanical properties of dissimilar friction stir welded AZ61/AZ40 joint