Abstract:Thermal spray cermet based on tungsten carbide has been widely used due to its excellent wear resistance. The features of both carbide and binder phases are essential factors which determine the performance of cermet coating. The thermal cycling of WC–Co spray particles up to a temperature over the melting point of binder phase during thermal spraying involves the decarburization of carbide. The decarburization of carbide becomes severe with the decrease of carbide particle size, which makes it difficult yet to deposit a dense nanostructured WC–Co with a limited decarburization by thermal spraying. The decarburization not only reduces the wear-resistant phase but also leads to the formation of brittle Co–W–C ternary binder phase. Moreover, the limited decarburization involves the deposition of spray particle at a solid–liquid two-phase state with carbides at a solid state and metal binder in a molten state during spraying. High velocity impact of two-phase droplets as in high velocity oxy-fuel spraying (HVOF) results in the formation of a dense cermet coating and on the other hand leads to the possibility of rebounding of wear-resistant solid carbide particles. In this review article, the microstructural features of thermal spray WC–Co are examined based on the effect of the decarburization of tungsten carbide. The decarburization mechanisms of tungsten carbide are discussed for the control of decarburization of carbide. The effects of carbide particle size on the deposition process, adhesion of HVOF coating and wear performance of WC–Co coating as well are examined based on a solid–liquid two-phase deposition process. It is demonstrated that WC–Co cermet with different sizes of WC particles should be deposited by different processes. Moreover, the deposition of nanostructured WC–Co by thermal spraying and recent advances on the cold spraying of nanostructured WC–Co are introduced. The cold spraying with the proper design of spray powders will become promising process to deposit nanostructured WC–Co with pure cobalt binder with the hardness comparable to a sintered bulk and even high toughness of 18.9MPam1/2. The pure metastable metal binder phase evolved in the deposit makes it possible to deposit hard cermet through healing the non-bonded interfaces in the coating by post-spray annealing.

Mechanical Property and Wear Performance Dependence on Processing Condition for Cold-Sprayed WC-(nanoWC-Co)

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Preparation And Properties Of Cold Sprayed Nano Wc-17co Coating On Magnesium Alloy

Characterization of Nano-Structured WC-Co Deposited by Cold Spraying

Effect of Flame Conditions on Abrasive Wear Performance of Hvof Sprayed Nanostructured Wc-12co Coatings

Microstructure and mechanical property of high velocity oxy-fuel sprayed WC-Cr3C2-Ni coatings

Relationships Between Feedstock Structure, Particle Parameter, Coating Deposition, Microstructure and Properties for Thermally Sprayed Conventional and Nanostructured WC–Co

Thermal sprayed WC-Co coatings and their mechanical properties

Influence of nano-sized WC addition on the microstructure, residual stress, and tribological properties of WC-Co HVAF-sprayed coatings

Influence of WC Particle Size on the Mechanical Properties and Residual Stress of HVOF Thermally Sprayed WC–10Co–4Cr Coatings

Effect of Particle and Carbide Grain Sizes on a HVOAF WC-Co-Cr Coating for the Future Application on Internal Surfaces: Microstructure and Wear

Toughening of Cold-Sprayed Nanostructured WC-12Co Deposit Through Using Multimodal WC Particles and Annealing

Influence of Powder Structure on the Micro-Hardness and Fracture Toughness of Cold-Sprayed WC-12Co Deposit

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Microstructure, phase constitution and mechanical properties of WC-Cr3C2-CoNiLa coatings fabricated by using HVOF spraying core-shell powder

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Comparison of the Mechanical and Electrochemical Properties of WC-25Co Coatings Obtained by High Velocity Oxy-Fuel and Cold Gas Spraying

Influence of Powder Porous Structure on the Deposition Behavior of Cold-Sprayed Wc-12co Coatings

Effect of Nanometer WC Powder on Wear Resistance of Thermal Spraying Coating

Properties of Supersonic Plasma Sprayed WC-17Co Nano-coating

Influence of Substrate Hardness Transition on Built-Up of Nanostructured WC–12Co by Cold Spraying