Abstract:For laser-melting deposition (LMD), a computational fluid dynamics (CFD) model was developed using the volume of fluid and discrete element modeling techniques. A method was developed to track the flow behavior, flow pattern, and driving forces of liquid flow. The developed model was compared with experimental results in the case of AISI 304 stainless steel single-track depositions on AISI 304 stainless steel substrate. A close correlation was found between experiments and modeling, with a deviation of 1–3%. It was found that the LMD involves the simultaneous addition of powder particles that absorb a significant amount of laser energy to transform their phase from solid to liquid, resulting in conduction-mode melt flow. The bubbles within the melt pool float at a specific velocity and escape from the melt pool throughout the deposition process. The pores are generated if the solid front hits the bubble before escaping the melt pool. Based on the simulations, it was discovered that the deposited layer’s counters took the longest time to solidify compared to the overall deposition. The bubbles strived to leave through the contours in an excess quantity, but became stuck during solidification, resulting in a large degree of porosity near the contours. The stream traces showed that the melt flow adopted a clockwise vortex in front of the laser beam and an anti-clockwise vortex behind the laser beam. The difference in the surface tension between the two ends of the melt pool induces “thermocapillary or Benard–Marangoni convection” force, which is insignificant compared to the selective laser melting process. After layer deposition, the melt region, mushy zone, and solidified region were identified. When the laser beam irradiates the substrate and powder particles are added simultaneously, the melt adopts a backwards flow due to the recoil pressure and thermocapillary or Benard–Marangoni convection effect, resulting in a negative mass flow rate. This study provides an in-depth understanding of melt pool dynamics and flow pattern in the case of LMD additive manufacturing technique.

Modelling of the Melt Pool Geometry in the Laser Deposition of Nickel Alloys Using the Anisotropic Enhanced Thermal Conductivity Approach

On the application of the anisotropic enhanced thermal conductivity approach to thermal modelling of laser-based powder bed fusion processes

On Modeling the Thermal Behavior of Single and Quad Laser Melting of Powdered Nickel Alloy

Thermo-Fluid-Dynamic Modeling of the Melt Pool During Selective Laser Melting for AZ91D Magnesium Alloy

Study on the Numerical Simulation of the SLM Molten Pool Dynamic Behavior of a Nickel-Based Superalloy on the Workpiece Scale

Effect of Laser Beam Profile on Thermal Transfer, Fluid Flow and Solidification Parameters during Laser-Based Directed Energy Deposition of Inconel 718

Accurate prediction of melt pool shapes in laser powder bed fusion by the non-linear temperature equation including phase changes - isotropic versus anisotropic conductivity

Computational Study of Transport Phenomena in Laser Melting-Based Metal Additive Manufacturing

Comparative Analysis of Melt Pool Evolution in Selective Laser Melting of Inconel 625 and Inconel 718 Nickel-Based Superalloys

Laser Metal Deposition of Rene 80—Microstructure and Solidification Behavior Modelling

Mesoscopic Computational Fluid Dynamics Modelling for the Laser-Melting Deposition of AISI 304 Stainless Steel Single Tracks with Experimental Correlation: A Novel Study

Application of finite element, phase-field, and CALPHAD-based methods to additive manufacturing of Ni-based superalloys

Thermomechanical Process Simulation and Experimental Verification for Laser Additive Manufacturing of Inconel®718.

Thermodynamic Behavior and Microstructure Evolution of Inconel 718 Alloy by Laser Metal Deposition

Laser Remelting Process Simulation and Optimization for Additive Manufacturing of Nickel-Based Super Alloys

Rapid Serum Minocycline Assay for Pleurodesis Monitoring Using High‐Performance Liquid Chromatography with Radial Compression

Analytical Modelling of Scanning Strategy Effect on Temperature Field and Melt Track Dimensions in Laser Powder Bed Fusion

Improving the accuracy and reliability of temperature field simulation during laser metal deposition

Thermal-fluid dynamic behavior and its effect on particle distribution and solidification characterization during the laser melting deposition of Ti-based composites

Numerical simulation on melt pool and solidification in the direct energy deposition process of GH3536 powder superalloy

Integrated modelling and simulation of NiTi alloy by powder bed fusion: Single track study