Abstract:The present paper focuses on the heat transfer and contact pressure at the casting-die interface in squeeze casting process. Experiments were conducted and a "plate shape" was used to cast aluminum alloy A356 in H13 steel die. Based on the temperature measurements inside the die, the interfacial heat transfer coefficient (IHTC) at the metal-die interface was determined by applying an inverse approach. The pressure at the metal-die interface was measured by using Kistler pressure transducer. The acquired data were processed by a low pass filtering method based on Fast Fourier Transform (FFT). Besides, a set of methods was set up to verify the computer program for the inverse model. The results show that the pressure at the casting-die interface and the IHTC rose to the peak value almost simultaneously as soon as the pressure was applied by the press. The higher the applied pressure, the higher the peak value of the IHTC and the pressure at the casting-die interface. It was a pressure maintaining stage immediately after the pressure was applied. During this stage, the pressure at the casting-die interface decreased immediately after it reached the peak value. The IHTC sharply dropped at the beginning. Then, the decrease rate of the IHTC became lower and lower. Besides, the IHTC of the cases with pressure applied was much higher than those without pressure applied. It indicates that the applied pressure greatly improved the contact status of casting and die surfaces and reduced the thermal resistance between the two surfaces. The IHTC profiles of the cases with the pressures 23 MPa and 46 MPa applied did not make much difference, however, when the applied pressure reached 70 MPa, the influence of the pressure at the casting die interface on the IHTC became very remarkable. (C) 2017 Elsevier Ltd. All rights reserved.

Study on the interfacial heat transfer coefficient between AZ91D magnesium alloy and silica sand

Determination of Interfacial Heat Transfer Coefficient at the Frozen Sand Mold Casting Process of ZL101 Alloy

Study on the Heat Transfer at the Casting-Mould Interface in Resin-Bonded Sand Mould Casting of Mg-Gd-Y-Zr Alloy

Determination of the Interfacial Heat Transfer Coefficient at the Metal-Sand Mold Interface in Low Pressure Sand Casting

Study on Interfacial Heat Transfer Coefficient at Metal/die Interface During High Pressure Die Casting Process of AZ91D Alloy

Spatial interfacial heat transfer and surface characteristics during gravity casting of A356 alloy

An Inverse Estimation of Frozen Sand Mold-Melt Heat Transfer Coefficient in the Solidification of A356 Alloy

STUDY OF INTERFACIAL HEAT TRANSFER COEFFI-CIENT BETWEEN METAL AND DIE DURING HIGH PRESSURE DIE CASTING PROCESS OF ALUMINUM ALLOY ADCl2Z

Determination of Interfacial Heat Transfer Behavior at the Metal/Shot Sleeve of High Pressure Die Casting Process of AZ91D Alloy

Study on the Relationship Between Interfacial Heat Transfer Coefficient and Interface Pressure in Squeeze Casting by Using Microscopic Contact Model

Experimental Study on the Heat Transfer Behavior and Contact Pressure at the Casting-Mold Interface in Squeeze Casting of Aluminum Alloy

Investigation and Application of Inverse Determination of Interfacial Heat Transfer Coefficient in Vacuum Investment Casting

Study on Heat Transfer Behavior at Metal/Die Interface in Aluminum Alloy Die Casting Process - I. Experimental Study and Determination of the Interfacial Heat Transfer Coefficient

Determination of the Heat Transfer Coefficient at Metal–die Interface of High Pressure Die Casting Process of AM50 Alloy

Measurement of Temperature Inside Die and Estimation of Interfacial Heat Transfer Coefficient in Squeeze Casting

Study on effects of heat treatment on morphology of Al coating on the surface of Mg alloy by cold spray

A Study on Heat Transfer at Metal/Die Interface During High Pressure Die Casting of AM60B Alloy

RELATIONSHIP BETWEEN METAL-DIE INTERFACIAL HEAT TRANSFER COEFFICIENT AND CASTING SOLIDIFICATION RATE IN HIGH PRESSURE DIE CASTING PROCESS

Interfacial reaction between AZ91D magnesium alloy melt and mild steel under high temperature

Macro/Micro Modeling of Casting Process of Magnesium Alloys

Determination of casting parameters of thick wall die-casting of magnesium alloy and simulation of its processing