Abstract:In this work, planar perovskite solar cells (PSCs) based on CH3NH3PbI3 perovskite layer and low-temperature processed TiO2 have been fabricated. Polymers including poly(methylmethacrylate) (PMMA), poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-pheny- lenevinylene] (MEH-PPV) and polyethylene glycol (PEG) in chlorobenzene solution have been selected to modify the interface between perovskite and hole transport layer (HTL), respectively. The concentrations of the three polymer solutions have been optimized. The effect of interfacial modification by different polymer solutions on the photoelectric properties of perovskite layer and the performance of PSCs has been systematically investigated. The microstructure and photoelectric properties of the modified perovskite films has been systematically studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), conducting force microscopy (CFM) and Kelvin probe force microscopy (KPFM). The results reveal that the modified perovskite films with tetrahedral perovskite structure have lager grain size, lower roughness and better photoelectric properties compared with the reference sample. The electron trap state density (Dtrap), charge extraction, carrier transfer and recombination process in the PSCs have been investigated by current-voltage (I-V) characteristic curves, steady-state photoluminescence (PL), photo-voltage decay and electrochemical impedance spectroscopy (EIS). The results indicate that the polymeric interface modification at the optimum concentration can reduce the Dtrap, promote the charge transfer and suppress carrier recombination, resulting in the improved performance of PSCs. All of the modified PSCs at an optimum concentration exhibit the improved fill factor (FF) and open circuit voltage (Voc), thus the power conversion efficiency (PCE) is enhanced to over 17% from 15.49%.

Interfacial engineering of self-assembled monolayer modified semi-roll-to-roll planar heterojunction perovskite solar cells on flexible substrates

Pseudohalide-Induced Recrystallization Engineering for CH3NH3PbI3 Film and Its Application in Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

Enhanced Photovoltaic Performance of CH3NH3PbI3 Perovskite Solar Cells Through Interfacial Engineering Using Self-Assembling Monolayer.

Interfacial engineering by using self-assembled monolayer in mesoporous perovskite solar cell

Self-organization of amine-based cathode interfacial materials in inverted polymer solar cells.

Facile post‐treatment of self‐assembled monolayers for efficient inverted perovskite solar cells

Polymer-modified halide perovskite films for efficient and stable planar heterojunction solar cells.

Repairing Interfacial Defects in Self-Assembled Monolayers for High-Efficiency Perovskite Solar Cells and Organic Photovoltaics through the SAM@Pseudo-Planar Monolayer Strategy

Tailoring the Interfacial Chemical Interaction for High-Efficiency Perovskite Solar Cells

Reconfiguration toward Self‐Assembled Monolayer Passivation for High‐Performance Perovskite Solar Cells

Microstructure Modulation Of The Ch3nh3pbi3 Layer In Perovskite Solar Cells By 2-Propanol Pre-Wetting And Annealing In A Spray-Assisted Solution Process

Enhancing the Efficiency of Low-Temperature Planar Perovskite Solar Cells by Modifying the Interface Between Perovskite and Hole Transport Layer with Polymers

Preheating-assisted deposition of solution-processed perovskite layer for an efficiency-improved inverted planar composite heterojunction solar cell

A facile spray-assisted fabrication of homogenous flat CH3NH3PbI3 films for high performance mesostructure perovskite solar cells

Enhancing Surface Modification and Carrier Extraction in Inverted Perovskite Solar Cells via Self-Assembled Monolayers

Self-Assembled Monolayers of Bi-Functionalized Porphyrins: A Novel Class of Hole-Layer-Coordinating Perovskites and Indium Tin Oxide in Inverted Solar Cells

Facile Fabrication of Self‐Assembly Functionalized Polythiophene Hole Transporting Layer for High Performance Perovskite Solar Cells

Refining the Substrate Surface Morphology for Achieving Efficient Inverted Perovskite Solar Cells

Compact Hole‐selective Self‐assembled Monolayers Enabled by Disassembling Micelles in Solution for Efficient Perovskite Solar Cells

Spin‐coated and vacuum‐processed hole‐extracting self‐assembled multilayers with H‐aggregation for high‐performance inverted perovskite solar cells

Self-Organized Fullerene Interfacial Layer for Efficient and Low-Temperature Processed Planar Perovskite Solar Cells with High Uv-Light Stability