Graphene Aerogel Prepared by Thermal Evaporation of Graphene Oxide Suspension Containing Sodium Bicarbonate

Shaolin Yang,Li Zhang,Qiuyun Yang,Zihan Zhang,Bo Chen,Peng Lv,Wei Zhu,Guanzhong Wang

DOI: https://doi.org/10.1039/c5ta01222h

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:We present a new type of in situ reduction-assembly approach to construct graphene hydrogel through simultaneous water evaporation and graphene oxide reduction.

What problem does this paper attempt to address?

Graphene Aerogel Derived by Purification-Free Graphite Oxide for High Performance Supercapacitor Electrodes

Xiao-Ning Tang,Cheng-Zhe Liu,Xiang-Rong Chen,Ya-Qian Deng,Xiao-Hu Chen,Jiao-Jing Shao,Quan-Hong Yang

DOI: https://doi.org/10.1016/j.carbon.2019.01.096

IF: 10.9

2019-01-01

Carbon

Abstract:Graphite oxide (GO), often being used as a precursor of graphene-based materials, can be prepared through a modified Hummers' method. The last step of GO synthesis, i. e. the removal of hydrogen chloride (HCl), is generally time-consuming, costly and polluting. Herein, the HCl-containing graphite oxide (H-GO) and pure GO aqueous suspensions were respectively hydrothermally treated followed by freeze-drying, leading to two graphene aerogels (H-GA and GA). Characterization results show that the two aerogels possess similar microstructure but distinct surface chemistry properties. When used as the active electrode materials in supercapacitors, GA and H-GA show comparable electrochemical properties in KOH aqueous electrolyte. In EMIMBF4 ionic liquid electrolyte, H-GA shows larger specific capacitance (243 F g(-1) at 1 A g(-1)), better rate capability, and higher energy density (135 Wh kg(-1) at 1 kW kg(-1)) compared with GA (216 F g(-1), 120Wh kg(-1)), which is attributed to its higher O/C ratio and better electrolyte wettability. We propose that it is not always necessary to conduct the HCl removal, and H-GO could be directly used as a precursor, which not only saves the time and cost remarkably but also may open up a relatively facile route to fabricate some graphene-based functional bulk materials. (c) 2019 Elsevier Ltd. All rights reserved.
Superhydrophobic and Superoleophilic Graphene Aerogel Prepared by Facile Chemical Reduction

Liming Xu,Guyu Xiao,Caibao Chen,Run Li,Yiyong Mai,Guoming Sun,Deyue Yan

DOI: https://doi.org/10.1039/c5ta00383k

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:A superhydrophobic neat graphene aerogel that exhibited excellent properties for oil-absorption and oil–water separation has been fabricated for the first time.
A Facile Approach to Superhydrophobic and Superoleophilic Graphene/polymer Aerogels

Run Li,Caibao Chen,Jing Li,Liming Xu,Guyu Xiao,Deyue Yan

DOI: https://doi.org/10.1039/c3ta14262k

IF: 11.9

2014-01-01

Journal of Materials Chemistry A

Abstract:Superhydrophobic and superoleophilic graphene/polyvinylidene fluoride (G/PVDF) aerogels were prepared by solvothermal reduction of the graphene oxide and PVDF mixed dispersions. The chemical reduction of the graphene oxide component was verified by FT-IR, XRD, XPS, Raman spectroscopy and TGA. The as-prepared aerogel showed high specific surface area, eminent absorption capacity for oils and organic solvents, superior water repelling ability, excellent absorption recyclability, and considerable mechanical properties. Therefore, this kind of aerogel is a promising material for oil–water separation, oil spill cleanup and recovery of organic solvents. Moreover, this work paved a facile way to fabricate superhydrophobic and superoleophilic graphene-based aerogels with graphene oxide and a hydrophobic polymer.
Graphene oxide aerogel ‘ink’ at room temperature, and ordered structures by freeze casting

Chunhui Wang,Ming Huang,Rodney S. Ruoff

DOI: https://doi.org/10.1016/j.carbon.2021.07.046

IF: 10.9

2021-10-01

Carbon

Abstract:A simple 'drop-by-drop' deposition method was invented to make graphene oxide (G-O) hydrogels at room temperature. Graphite oxide was synthesized at 5 °C for a low defect density in the carbon lattice, and was then dispersed in water to form "G-O(5)". This water dispersion was converted into a G-O(5) ink by adding l-ascorbic acid and the ink could then be deposited onto any substrate to prepare hydrogels using a dropper; using this gelation method, a stable hydrogel is formed within 1 hour at room temperature, without heating or high pressure. Hydrogels with desired patterns and sizes were readily deposited on various substrates. This method provides efficient control over the hydrogel and it was readily made into forms such as films, fibers, and aerogels. Freeze casting the hydrogel caused the G-O(5) sheets to assemble into a long-range lamellar structure, by controlling the growth pattern of the ice crystals that formed the lamellae when the hydrogel was frozen. The deposition of this G-O(5) ink at room temperature allows straightforward fabrication of G-O aerogels with ordered structures.

materials science, multidisciplinary,chemistry, physical
Three-dimensional graphene-based aerogels prepared by a self-assembly process and its excellent catalytic and absorbing performance

Tao Wu,Mingxi Chen,Lei Zhang,Xiaoyang Xu,Yu Liu,Jing Yan,Wei Wang,Jianping Gao

DOI: https://doi.org/10.1039/c3ta10989e

IF: 11.9

2013-01-01

Journal of Materials Chemistry A

Abstract:A simple one-step method for fabricating graphene-based hydrogels (GHs) with interconnected 3D networks using Cu nanoparticles was developed. During this process, graphene oxide (GO) was reduced by Cu nanoparticles to form reduced GO (rGO) which then self-assembled to form GHs. Meanwhile, the Cu nanoparticles were oxidized to form copper(I) oxide which deposited onto the rGO sheets and became imbedded in the GHs. The GHs were transformed to graphene-based aerogels (GAs) by a green freeze-drying method. The composition of the GAs can be easily adjusted by simply changing the initial amount of Cu nanoparticles or the concentration of the GO suspension. The GAs not only possess good catalytic performance for the catalytic reduction of 4-nitrophenol and the photocatalytic degradation of methyl orange but also have excellent capacities for removing various oils and dyes from water.
(3-Mercaptopropyl)trimethoxysilane-assisted Synthesis of Macro- and Mesoporous Graphene Aerogels Exhibiting Robust Superhydrophobicity and Exceptional Thermal Stability

Shuai Zhou,Xiang Zhou,Wei Jiang,Tianhe Wang,Ning Zhang,Yue Lu,Liuhua Yu,Zuozhu Yin

DOI: https://doi.org/10.1021/acs.iecr.5b03179

2016-01-01

Industrial & Engineering Chemistry Research

Abstract:Robust superhydrophobic and exceptionally thermostable graphene aerogels exhibiting a three-dimensional macro- and mesoporous structure have been synthesized through a (3-mercaptopropyl)trimethoxysilane-assisted two-step route with natural drying. The facile synthetic process not only guarantees their excellent performance but also greatly improves their practical production rate. The prepared graphene aerogels hold excellent superhydrophobicity, for which water contact angle exceeded 160 degrees, even after 20 ethanol washing–drying cycles. Furthermore, the self-assembly functionalized-graphene sheets enhance the thermal stability of the nanocomposites, due to the good dispersion of functionalized-graphene sheets and the strong bonding between graphene sheets and polymer chains within the aerogels. The study implies a novel and practical methodology to efficiently fabricate three-dimensional composite materials with enhanced performances.
Macroscopic Multifunctional Graphene-Based Hydrogels and Aerogels by a Metal Ion Induced Self-Assembly Process

Huai-Ping Cong,Xiao-Chen Ren,Ping Wang,Shu-Hong Yu

DOI: https://doi.org/10.1021/nn300082k

IF: 17.1

2012-01-01

ACS Nano

Abstract:We report a one-step fabrication of macroscopic multifunctional graphene-based hydrogels with robust interconnected networks under the synergistic effects of the reduction of graphene oxide sheets by ferrous ions and in situ simultaneous deposition of nanoparticles on graphene sheets. The functional components, such as α-FeOOH nanorods and magnetic Fe(3)O(4) nanoparticles, can be easily incorporated with graphene sheets to assemble macroscopic graphene monoliths just by control of pH value under mild conditions. Such functional graphene-based hydrogels exhibit excellent capability for removal of pollutants and, thus, could be used as promising adsorbents for water purification. The method presented here is proved to be versatile to induce macroscopic assembly of reduced graphene sheets with other functional metal oxides and thus to access a variety of graphene-based multifunctional nanocomposites in the form of macroscopic hydrogels or aerogels.
Pristine Graphene Aerogels by Room-Temperature Freeze Gelation.

Yue Lin,Fei Liu,Gabriel Casano,Rupesh Bhavsar,Ian A Kinloch,Brian Derby

DOI: https://doi.org/10.1002/adma.201602393

IF: 29.4

2016-01-01

Advanced Materials

Abstract:Aerogels can be fabricated from pristine graphene exfoliated nanosheets using freeze gelation with nonaqueous solvents and no heat treatment or reduction stage. Solvents are selected that disperse pristine graphene with a melting point above room temperature but with a high vapor pressure above the solid at room temperature, enabling sublimation (freeze drying) under ambient conditions.
Gelatin-assisted Fabrication of Water-Dispersible Graphene and Its Inorganic Analogues

Yu Ge,Jialiang Wang,Zixing Shi,Jie Yin

DOI: https://doi.org/10.1039/c2jm33173j

2012-01-01

Journal of Materials Chemistry

Abstract:Two dimensional nanomaterials are of great significance in a wide range of applications due to their high surface area and novel properties. Here we offer a simple and large-scale method to prepare graphene and its inorganic analogues (MoS2, WS2 and boron nitride) by the sonication of their bulk materials in an aqueous solution of gelatin. The concentrations of the obtained stable dispersions were up to 0.6, 0.8, 0.9 and 1.4 mg mL(-1) for graphene, MoS2, WS2 and boron nitride, respectively. Transmission electron microscopy strongly suggests that the materials have been exfoliated into few- or mono-layer thin sheets. Specifically, graphene and MoS2 dispersion have been directly employed to fabricate gelatin-graphene composites. Scanning electron microscope images show that graphene flakes were homogeneously dispersed in the composites. The tensile test results show that the mechanical properties of gelatin films have been remarkably improved by graphene rather than MoS2.
The preparation of graphene foam by one-step reduction and air-drying for oil–water separation

Yiyun Geng,Zheng Li,Mumei Chen,Haogui Zhao,Lan Zhang

DOI: https://doi.org/10.1007/s10971-020-05240-z

2020-02-07

Abstract:The freeze-drying or supercritical CO<sub>2</sub> drying methods are usually used to remove the solvent to keep the shape of material in traditional methods for preparing graphene foam. Porous frozen tofu is a kind of traditional Chinese food and prepared through a process of freezing casting and thawing. Inspired by it, a green and economic approach for graphene foam (GF) synthesis using one-step reduction and air-drying is reported in this article. By controlling the reduction time and precursor concentration, monolithic GF with a little or without volume shrinkage can be obtained after a simple pre-freezing, thawing, and air-drying step of the graphene hydrogel. The obtained GF shows low density (17.5 mg/cm<sup>3</sup>), superelastic, high recyclability, and excellent oil absorption ability. During the whole preparation process, the conditions were mild, and no special equipment such as freezer dryer was used, which is beneficial to large-scale production of porous GF with high oil adsorption and recyclability.

materials science, ceramics
Synthesis of graphene aerogel materials by hydrothermal method without the use of reducing agents

Chuyen Phan Thi,Ha Vu Thi Thu

DOI: https://doi.org/10.51316/jca.2020.017

2020-04-30

Vietnam Journal of Catalysis and Adsorption

Abstract:Graphene Aerogel (GA) is the lightest material in over the world. This material has high surface area with many layers of single graphene and has potential applications for adsorption, catalysis and storage. In this study, graphene aerogel materials were successfully synthesized by environmentally friendly hydrothermal methods without the use of reducing agents and were dryed by supercritical CO2 to avoid secondary environmental pollution. The obtained GA materials were characterized by Brunauer- Emmett- Teller (BET) surface area measurements, scanning electron microscopy (SEM), Raman spectroscopy. Results showed that with hydrothermal time of 5 hours and GO concentration of 2,5 mg/mL, GA material has highest surface area of 941 m2/g and lowest density of 0,0226 g/cm3.
Graphene nanosheets synthesis via chemical reduction of graphene oxide using sodium acetate trihydrate solution

xinmeng zhang,kezhi li,hejun li,jinhua lu,qiangang fu,yanhui chu

DOI: https://doi.org/10.1016/j.synthmet.2014.04.007

IF: 4

2014-01-01

Synthetic Metals

Abstract:•Graphene oxide was reduced by a novel reducing reagent sodium acetate trihydrate.•The water-dispersible properties of the reduced graphene oxide are poor.•Reduced graphene oxide formed some new and smaller average size of the sp2 domains.•A reduction mechanism of graphene oxide by sodium acetate trihydrate was proposed.•The thermal stability of reduced graphene oxide than that of graphene oxide.
Graphene aerogels: a review

George Gorgolis,Costas Galiotis

DOI: https://doi.org/10.1088/2053-1583/aa7883

IF: 6.861

2017-06-22

2D Materials

Abstract:Graphene based aerogels (GAs) are 3D scaffold materials that can be lighter than air. Due to their fascinating properties, such as, high mechanical strength and electrical conductivity, thermal resistance and adsorption capacity, they have attracted a lot of interest currently. This review, covers the main routes for obtaining GAs namely, hydrothermal reduction/self-assembly, chemical reduction, template-directed reduction, cross-linking and sol–gel processes. Potential application fields for example in energy storage and environmental protection are also discussed. Finally, the future prospects of this exciting field based on the results published so far are examined.

materials science, multidisciplinary
Conductive Resilient Graphene Aerogel Via Magnesiothermic Reduction of Graphene Oxide Assemblies

Huang Tang,Peibo Gao,Zhihao Bao,Bin Zhou,Jun Shen,Yongfeng Mei,Guangming Wu

DOI: https://doi.org/10.1007/s12274-014-0672-z

2015-01-01

Abstract:Graphene aerogels are desirable for energy storage and conversion, as catalysis supports, and as adsorbents for environmental remediation. To produce graphene aerogels with low density, while maintaining high electrical conductivity and strong mechanic performance, we synthesized graphene aerogels by the magnesiothermic reduction of a freeze-dried graphene oxide (GO) self-assembly and subsequent etching of the formed MgO in acid solution. The reduced graphene oxide (rGO) aerogel samples exhibited densities as low as 1.1 mg·cm −3 . The rGO aerogel was very resilient, exhibiting full recoveryeven after being compressed by strains of up to 80%; its elastic modulus (E) scaled with density (ρ) as E∼ρ 2 . The rGO aerogels also exhibited high conductivities (e.g., 27.7 S·m −1 at 3.6 mg·cm −3 ) and outperformed many rGO aerogels fabricated by other reduction processes. Such outstanding properties were ascribed to the microstructures inherited from the freeze-dried GO self-assembly and the magnesiothermic reduction process.
Self-Assembly and Embedding of Nanoparticles by in Situ Reduced Graphene for Preparation of A 3d Graphene/Nanoparticle Aerogel

Wufeng Chen,Sirong Li,Chunhua Chen,Lifeng Yan

DOI: https://doi.org/10.1002/adma.201102838

IF: 29.4

2011-01-01

Advanced Materials

Abstract:A 3D graphene architecture can be prepared via an in situ self-assembly of graphene prepared by a mild chemical reduction. Fe3O4 nanoparticles are homogeneously dispersed into a graphene oxide (GO) aqueous suspension, and a 3D magnetic graphene/Fe3O4 aerogel is prepared during the reduction of GO to graphene. This provides a general method to prepare 3D graphene/nanoparticle composites for a wide range of applications including catalysis and energy conversion.
Graphene aerogels: part 1 - derived from graphene oxide and thermally reduced graphene oxide via supercritical carbon dioxide drying

Meryem Samanci,Ayşe Bayrakçeken

DOI: https://doi.org/10.55730/1300-0527.3657

2024-02-08

Abstract:Graphene aerogels have become promising materials in many areas of industry, especially in energy applications due to their superior physical and electrochemical properties. Generally, graphene oxide (GO)-derived aerogels (A) are synthesized by using the hydrothermal method. In this study, both GO and reduced graphene oxide (RGO)-derived aerogels were synthesized by using the sol-gel method coupled with the supercritical carbon dioxide (SCCO2) drying process. It aims to examine the changes in the structure of the final aerogel by changing the amount (0.25-0.5-1% wt.) and type of graphene-based precursor materials used in the synthesis. Physical characterizations of graphene aerogels were conducted using Brunauer-Emmett-Teller (BET) analysis, scanning electron microscope-energy dispersive X-ray (SEM-EDX) analysis, transmission electron microscopy (TEM), micro-Raman spectroscopy, X-ray diffractometer (XRD) to highlight their structural properties. Additionally, X-ray photoelectron spectroscopy (XPS) analyses were performed to determine the oxidation levels on the surface of the RGO-1 aerogel. The cyclic voltammetry (CV) method was used to examine the electrochemical behavior of the graphene aerogels against corrosion. Specific capacitance values of the synthesized materials were calculated before and after corrosion. Furthermore, the surface charge changes that occur after corrosion were examined. GOAs displayed the highest specific capacitance value among graphene aerogels. Notably, the RGOA-1 aerogel exhibited the highest corrosion resistance. The pseudo-capacitive charge ratio of RGOA-1 after corrosion was measured at 0.5 mC cm-2.
Freeze-Casting Produces a Graphene Oxide Aerogel with a Radial and Centrosymmetric Structure

Chunhui Wang,Xiong Chen,Bin Wang,Ming Huang,Bo Wang,Yi Jiang,Rodney S. Ruoff

DOI: https://doi.org/10.1021/acsnano.8b01747

IF: 17.1

2018-01-01

ACS Nano

Abstract:We report the assembly of graphene oxide (G-O) building blocks into a vertical and radially aligned structure by a bidirectional freeze-casting approach. The crystallization of water to ice assembles the G-O sheets into a structure, a G-O aerogel whose local structure mimics turbine blades. The centimeter-scale radiating structure in this aerogel has many channels whose width increases with distance from the center. This was achieved by controlling the formation of the ice crystals in the aqueous G-O dispersion that grew radially in the shape of lamellae during freezing. Because the shape and size of ice crystals is influenced by the G-O sheets, different additives (ethanol, cellulose nanofibers, and chitosan) that can form hydrogen bonds with H2O were tested and found to affect the interaction between the G-O and formation of ice crystals, producing ice crystals with different shapes. A G-O/chitosan aerogel with a spiral pattern was also obtained. After chemical reduction of G-O, our aerogel exhibited elasticity and absorption capacity superior to that of graphene aerogels with "traditional" pore structures made by conventional freeze-casting. This methodology can be expanded to many other configurations and should widen the use of G-O (and reduced G-O and "graphenic") aerogels.
Facile preparation of graphene aerogel as a thermal insulation material

Xiangxiang Du,Yadan Ran,Yaqian Fan,Yongchun Zhao,Xuejun Shi

DOI: https://doi.org/10.1080/1536383x.2024.2398806

IF: 2.06

2024-09-04

Fullerenes Nanotubes and Carbon Nanostructures

Abstract:A simple low temperature and cost-effective hydrothermal method via reduction self-assembly and freeze-drying was fabricated to prepare graphene aerogel (rGO). After the reduction process, most of the oxygen-containing groups in graphene oxide have been removed by ascorbic acid. The surface C/O atomic ratio detected in rGO is about 7.26. The aerogel presents a nanoporous structure. This porous structure could act as a barrier to heat conduction. By heating the graphene aerogel and using infrared thermal imager to detect the temperature, the temperature difference between the top and the bottom of the aerogel reached 80 °C, which showed excellent thermal insulation performance. In addition, by testing the thermal imaging image of graphene aerogel placed on the skin surface, it exhibited an infrared stealth effect. This carbon aerogel may offer potential for the fabrication and application for thermal insulation and infrared stealth material systems.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,physics, atomic, molecular & chemical
High-Performance Self-Assembled Graphene Hydrogels Prepared by Chemical Reduction of Graphene Oxide

Sheng Kai-xuan,Xu Yu-xi,Li Chun,Shi Gao-quan

DOI: https://doi.org/10.1016/s1872-5805(11)60062-0

IF: 5.7

2011-01-01

New Carbon Materials

Abstract:Three-dimensional self-assembled graphene hydrogels (SGHs) have been fabricated by chemical reduction of graphene oxide (GO) with sodium ascorbate. The SGHs were characterized by scanning electron microscopy, rheological tests, electrical conductivity measurements, X-ray photoelectron spectroscopy, X-ray diffraction, and Raman spectroscopy. Results indicate that the reduction of GO promotes the assembly of graphene sheets. The SGHs are electrically conductive (1 S·m−1) and mechanically strong and exhibit excellent electrochemical performance. In 1 mol·L−1 aqueous solution of H2SO4, the specific capacitance of SGHs was measured to be about 240 F·g−1 at a discharge current density of 1.2 A·g−1.
Surfactant- and Sonication- Free Exfoliation Approach to Aqueous Graphene Dispersion

Shufen Wang,Chao Wang,Xiang Ji,Mingzhang Lin

DOI: https://doi.org/10.1016/j.matlet.2018.01.064

IF: 3

2018-01-01

Materials Letters

Abstract:A Li+-OH exfoliation system was designed to prepare graphene in water without surfactants or sonication. Due to the positive charge transferred from intercalating Li+ ions to adjacent C atoms, OH could add on the graphene sheets and further promote their affinity to water, resulting in efficient exfoliation of graphene in water. The as-prepared graphene concentration was up to 0.09 mg.mL (1), and sheet sizes range from 1 to 2 mu m. Detailed characterizations revealed the formation of high-quality and few-layer graphene sheets and confirmed the addition of hydroxyl groups on graphene sheets during exfoliation. This strategy has potential in scalable production of graphene in aqueous phase. (C) 2018 Elsevier B.V. All rights reserved.

Graphene Aerogel Prepared by Thermal Evaporation of Graphene Oxide Suspension Containing Sodium Bicarbonate

Graphene Aerogel Derived by Purification-Free Graphite Oxide for High Performance Supercapacitor Electrodes

Superhydrophobic and Superoleophilic Graphene Aerogel Prepared by Facile Chemical Reduction

A Facile Approach to Superhydrophobic and Superoleophilic Graphene/polymer Aerogels

Graphene oxide aerogel ‘ink’ at room temperature, and ordered structures by freeze casting

Three-dimensional graphene-based aerogels prepared by a self-assembly process and its excellent catalytic and absorbing performance

(3-Mercaptopropyl)trimethoxysilane-assisted Synthesis of Macro- and Mesoporous Graphene Aerogels Exhibiting Robust Superhydrophobicity and Exceptional Thermal Stability

Macroscopic Multifunctional Graphene-Based Hydrogels and Aerogels by a Metal Ion Induced Self-Assembly Process

Pristine Graphene Aerogels by Room-Temperature Freeze Gelation.

Gelatin-assisted Fabrication of Water-Dispersible Graphene and Its Inorganic Analogues

The preparation of graphene foam by one-step reduction and air-drying for oil–water separation

Synthesis of graphene aerogel materials by hydrothermal method without the use of reducing agents

Graphene nanosheets synthesis via chemical reduction of graphene oxide using sodium acetate trihydrate solution

Graphene aerogels: a review

Conductive Resilient Graphene Aerogel Via Magnesiothermic Reduction of Graphene Oxide Assemblies

Self-Assembly and Embedding of Nanoparticles by in Situ Reduced Graphene for Preparation of A 3d Graphene/Nanoparticle Aerogel

Graphene aerogels: part 1 - derived from graphene oxide and thermally reduced graphene oxide via supercritical carbon dioxide drying

Freeze-Casting Produces a Graphene Oxide Aerogel with a Radial and Centrosymmetric Structure

Facile preparation of graphene aerogel as a thermal insulation material

High-Performance Self-Assembled Graphene Hydrogels Prepared by Chemical Reduction of Graphene Oxide

Surfactant- and Sonication- Free Exfoliation Approach to Aqueous Graphene Dispersion