Abstract:The volume fraction and stabilization of retained austenite at room temperature were determined by the degree of stable element partitioning of austenite. The element diffusion behaviors usually had a close relationship with crystal defects, and dislocation multiplication caused by high temperature deformation might also increase the vacancy concentration, which contributed to the diffusion of substitutional atoms and interstitial atoms. By adopting a new treatment process of intercritical deformation-hold-quenching (DIQ), the effect of Mn partitioning and the structure evolution of bainite under the deformation in intercritical area were studied. The microstructure, dislocation density and distribution of alloy elements, especially the volume fraction of retained austenite, were characterized by means of OM, SEM, TEM, EPMA and XRD. The results indicated that the grains of ferrite and the lathes of martensite were refined, the number of the block martensite was decreased, and dislocation density was increased from 0.36x10(14) m(-2) to 1.20x10(14) m(-2) after deformation. The mutual movement of dislocation slip increased vacancy concentration and the number of interstitial solute atoms, accelerated the diffusive rate of C atoms and Mn atoms from alpha phase to gamma phase, and promoted the partitioning effect of Mn element in the critical region. Eventually, the contents and areas of C and Mn enrichment were increased. By adopting the process of intercritical deformation-hold-austenitizing-quenching-partitioning in bainitic region-quenching (DI&Q&PB), the volume fraction of retained austenite was increased from 11.5% to 13.9%, and the carbon content in retained austenite was increased from 1.14% to 1.28%.

A Detailed Study of the Transformation Stasis Phenomenon during the Isothermal Bainite Transformation in Mn Based Low Alloy Steels

Analysis of Transformation Stasis During the Isothermal Bainitic Ferrite Formation in Fe–C–Mn and Fe–C–Mn–Si Alloys

Effect of Stacking Fault Energy and Austenite Strengthening on Martensitic Transformation in Fe-Mn-Si Alloys

Effect of Mn on the chemical driving force and bainite transformation kinetics in medium-manganese alloys

Thermodynamic analysis and isothermal bainitic transformation kinetics in lean medium-Mn steels

The Effect of Interfacial Element Partitioning on Ferrite and Bainite Formation

Predicting the Effect of Mo, Ni, and Si on the Bainitic Stasis

A thermodynamic study of inverse bainitic transformation

A general mixed-mode model for the austenite-to-ferrite transformation kinetics in Fe–C–M alloys

Application of interrupted cooling experiments to study the mechanism of bainitic ferrite formation in steels

A 2D Analysis of the Competition Between the Equiaxed Ferritic and the Bainitic Morphology Based on a Gibbs Energy Balance Approach

On the Transition Between Grain Boundary Ferrite and Bainitic Ferrite in Fe–C–Mo and Fe–C–Mn Alloys: the Bay Formation Explained

Difference in transformation behavior between ferrite and austenite formations in medium manganese steel

Effect of Mo Addition on the Transformation Stasis Phenomenon During the Isothermal Formation of Bainitic Ferrite

Analysis of phase transformation thermodynamics and kinetics and its relationship to structure-mechanical properties in a medium-Mn high strength steel

Thermodynamic–kinetic calculations and dilatometric verification of the martensitic and bainitic transformations in 4% medium-Mn steel

Predicting the Transition Between Upper and Lower Bainite Via a Gibbs Energy Balance Approach

Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: The significant impact on mechanical properties

Conversion Between Non-Isothermal and Isothermal Transformation Kinetics of Γ to Α for C–Mn and Nb Microalloyed Steels

Effect of Intercritical Dislocation Multiplication to Mn Partitioning and Microstructure Evolution of Bainite in Low Carbon Steel