Abstract:Nanograined powders including elemental metals, intermetallics, and composites have been prepared by mechanical milling. Constrained sinter-forging has been used to consolidate the powders to full density while maintaining nanophase grain sizes, with potential for near net-shape manufacturing. The addition of a second phase, especially when alloyed into the matrix uniformly during milling, facilitates the retention of nanostructures in consolidation. The versatile, solid-state, milling/consolidation approach leads to easy preparation of extremely uniform nanophase composites with multiple components having very different melting points and properties. Under uniaxial compression, very high strength and appreciable elongation to failure have been observed, reflecting the high density and nanocrystalline microstructure in these consolidated samples. Under tensile forces, however, the residual processing flaws may trigger premature catastrophic failure. The high-strength material with little capacity for strain hardening and strain rate hardening is susceptible to plastic instabilities such as necking in tension and shear banding. In this regard, ultrafine-grained microstructure (e.g., submicron grains), with grain sizes still at least a couple of orders of magnitude finer than conventional materials, can offer a balance for the desired combination of strength and ductility and at the same time be more amenable to full density processing. The shear banding mode as the dominant plastic deformation mechanism is discussed with bcc Fe as an example. Such a shear localization behavior resembles the response of amorphous alloys. It is not only of interest to scientific studies of the dependence of deformation mechanisms on grain size but also of practical value in certain high-rate applications such as kinetic energy penetrators.

Microhardness Enhancement in Fully Dense Fe-Based Nanophase Metallic Alloys

Macro-micro Analysis of Mechanical Properties of Al0.6CoCrFeNi High-Entropy Alloy Particle-Reinforced Al-based Composites

Full-density nanocrystalline Fe-29Al-2Cr intermetallic consolidated from mechanically milled powders

Nanophase Fe Alloys Consolidated to Full Density from Mechanically Milled Powders

Processing and Microhardness of Bulk Cu-Fe Nanocomposites

Nanophase Metallic Alloys Consolidated from Powders Prepared by Mechanical Alloying

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation

Grain growth and strengthening mechanisms of ultrafine-grained CoCrFeNiMn high entropy alloy matrix nanocomposites fabricated by powder metallurgy

Microstructure and Mechanical Properties of Ultrafine Grained CoCrFeNi and CoCrFeNiAl0.3 High Entropy Alloys Reinforced with Cr2O3/Al2O3 Nanoparticles

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Powder metallurgical processing of Al matrix composite reinforced with AlSiCrMnFeNiCu high-entropy alloys: Microstructure, thermal stability, and microhardness

Microstructural Characterization of AlCrCuFeMnNi Complex Concentrated Alloy Prepared by Pressureless Sintering

Formation of Nanoscale Metallic Glassy Particle Reinforced Al-Based Composite Powders by High-Energy Milling

Revealing the Microstructure Evolution and Mechanical Properties of Al2O3-Reinforced FCC-CoCrFeMnNi Matrix Composites Fabricated via Gas Atomization and Spark Plasma Sintering

Insight into the Microstructure and Micromechanical Behavior and Mechanism of the Constitutional Phase of FeNiCrAl0.63 Multi-Principal Element Alloy

Microstructural characteristics and mechanical behavior of microwave-assisted sintered ferromagnetic FeCoNi1.5CrCu HEAp/Al matrix composites

Nanophase And Ultrafine-Grained Powders Prepared By Mechanical Milling: Full Density Processing And Unusual Mechanical Behavior

Insight into the microstructure and micromechanical behavior and mechanism of the constitutional phase of FeNiCrAl 0.63 multi-principal element alloy

Consolidation and mechanical behaviour of nanophase iron alloy powders prepared by mechanical milling

Microstructure of nano-crystalline material Al60Fe20Cu20

Fabrication of CoCrFeNiMn High Entropy Alloy Matrix Composites by Thermomechanical Consolidation of a Mechanically Milled Powder