An Available Optical Thin Film Demultiplexer Based on Superprism Effect

x z sun,xu liu,p f gu,x y ni

DOI: https://doi.org/10.1364/oic.2007.thc8

2007-01-01

Abstract:An available optical thin film demultiplexer based on superprism effect was fabricated and tested in this paper.

What problem does this paper attempt to address?

Design of High-Level Reflectivity Thin Film Spatial Demultiplexer

JIN Bo,CHEN Hai-xing,ZHANG Yue-guang,GU Pei-fu,LIU Xu

DOI: https://doi.org/10.3785/j.issn.1008-973x.2005.04.004

2005-01-01

Abstract:A new design method for multilayer thin film spatial demultiplexer based on Superprism phenomenon of periodic photonic crystal was presented. Without complex techniques the multilayer thin film structure was deposited easily with increasing the thickness of the single layer and decreasing the periodicity. The high-level reflectivity thin film stack as 10(9H9L)9H was designed. By the above method and compared with the classic low-level high reflectivity thin film stack of the same geometric thickness, the numerical simulation and the computational results show that the spatial dispersion is large and the designed multiplayer structure is more feasible in practice for fabrication.
Tunable spatial demultiplexer based on the Fabry-Perot filter.

Xuezheng Sun,Peifu Gu,Mingyu Li,Xu Liu,Debing Wang,Jinlong Zhang

DOI: https://doi.org/10.1364/OE.14.008470

IF: 3.8

2006-01-01

Optics Express

Abstract:A thin-film Fabry-Perot filter (FPF) was designed and fabricated to achieve the superprism effect. A polychromatic light, tuned at various incident angles onto the device, was used to attain more demultiplexing channels. This indicates that the FPF, which can be fabricated simply and inexpensively, can be used as a tunable demultiplexing device. Further, the transfer matrix method (TMM) and the Gaussian angular spectrum method were introduced to calculate a more-accurate spatial shift at different wavelengths and to analyze the beam-splitting phenomena in the FPF. (c) 2006 Optical Society of America
Studies on Superprism Effects in Multilayer Thin Film Stacks

X. Liu,X. Z. Sun,P. F. Gu

DOI: https://doi.org/10.1117/12.625018

2005-01-01

Abstract:The concept of "Superprism" which is used in photonic crystal will be introduced into optical thin film coatings, due to the fact that the group velocity of the light is different as the wavelength in certain special case for the multiplayer thin film coatings. In this paper, The "superprism" effect of multilayer thin film coatings will be presented both from theoretical analysis and experimental results, these researches will create an new application of the thin film coatings not only to be a spectral filter but also can acts as "thin film gratings".
Enhanced superprism effect based on positive/negative lateral shift of reflective beam in a Fabry-Perot filter.

Xu Liu,Xuezheng Sun,Peifu Gu

DOI: https://doi.org/10.1364/OL.32.002321

IF: 3.6

2007-01-01

Optics Letters

Abstract:It is found that when a light beam is incident obliquely on a thin film Fabry-Perot filter (FPF) from different incident media (air or substrate), the reflective beam will be shifted in both the forward and the backward directions. Based on this inverted spatial dispersion effect, two thin film FPFs with different directional lateral shifts are assembled to get a thin film superprism with a wider dispersion band. The thin film samples are fabricated as well as tested, and the results are in approximate agreement with numerical simulation. (C) 2007 Optical Society of America.
Superprism effect with a large spatial dispersion and high efficiency in a reflection filter

Xuezheng Sun,Peifu Gu,Xiaoyong Ni,Mingyu Li,Xu Liu,Weidong Shen,Yueguang Zhang

DOI: https://doi.org/10.1088/1464-4258/10/2/025301

2008-01-01

Abstract:Reflection-type thin film demultiplexers are interesting for optical communication, detection and some other fields. In this work a novel thin film reflection filter is proposed to obtain a large spatial dispersion with high efficiency. Based on the abnormal reflective phase change, the reflected beam will be shifted spatially as a function of wavelength. The numerical simulation of the distribution of reflected light is investigated by a transfer matrix, along with the Gaussian angular spectrum method. A thin film sample is fabricated and tested, and the experimental results found to be in good agreement with numerical simulation.
Investigation of Multichannel Spatial Demultiplexer Based on Thickness-Tapered Thin Film Stacks

Xuezheng Sun,Xu Liu,Peifu Gu

DOI: https://doi.org/10.1016/j.optcom.2007.12.034

IF: 2.4

2008-01-01

Optics Communications

Abstract:A conventional high reflectance (HR) coating sandwiched between two thickness-tapered period thin film stacks is investigated to enhance multichannel spatial dispersion, since phase shift on reflection changes rapidly due to the mismatch induced by the overlaps of different reflective bands. Compared with ordinary Bragg reflector, this structure can be more freely to enhance multichannel spatial shift. The design, fabrication and testing results of this special multichannel filter were presented in the paper, and show the potential to act as a novel demultiplexer.
Color-Separation Multilayer Systems Used for Thin Film Transistor-Liquid Crystal Display

Yueguang Zhang,Peifu Gu,Xu Liu,Jinfa Tang

DOI: https://doi.org/10.3321/j.issn:0253-2239.1999.06.013

1999-01-01

Abstract:The color-separation multilayer systems operating in s-polarization or p-polarization components for thin film transistor liquid crystal display projectors were described. To reduce the trans-mission band ripples of the dichroic filters, the design for using s-polarization component was emphasized. Some experimental details and measuring results were reported.
Superprism Effect in Thin Film Fabry-Perot Filter

Chen Haixing,Gu Peifu,Lü Weige,Jin Bo,Li Haifeng,Liu Xü

DOI: https://doi.org/10.2529/piers041209002809

2005-01-01

PIERS Online

Abstract:For the sake of achieving remarkable superprism effect, we investigate in thin film Fabry-Perot filter which possess drastic change in phase and large group delay around wavelength of peak transmittance. The group delay and spatial dispersion shift are simulated numerically; while the device is fabricated and tested with the maximum spatial separation shift reach to 65�m . We also analyze Gaussian beam propagating in the device to give the interpretation of the spot splitting phenomenon in this experiment. Compared with the traditional prism, the total thickness of our structure is only 3.3�m , and shows a very large deflection angle about 30 ◦ /nm.
Based 0n High-Level Reflectivity Thin Film Spatial Demultiplexer Research

温凯,黄永清,段晓峰,黄辉,王琦

DOI: https://doi.org/10.3969/j.issn.1005-9490.2009.02.008

2009-01-01

Abstract:A new design method for multilayer thin film spatial demultiplexer based on Superprism phenomenon of periodic photonic crystal was presented.Without complex techniques the multilayer thin film structure was deposited easily with increasing the thickness of the single layer and decreasing the periodicity.The high-level relectivity thin film stack as 10(9H9L)9H was designed.By the above method and compared with the classic low-level high reflectivity thin film stack of the same geometric thickness,the numerical simulation and the computational results show that the spatial dispersion is large and the designed multiplayer structure is more feasible in practice for fabrication.
Spatial Dispersion of Optical Thin Films

Xu Liu,Zhen-yue Luo,Wei-dong Shen,Xue-zheng Sun,Pei-fu Gu

DOI: https://doi.org/10.1117/12.796688

2008-01-01

Abstract:Due to the gradient of the phase shift as the wavelength in the reflection and transmission, the optical thin films coatings will present the spatial dispersion effect. The new kinds of super-prism thin film devices can be realized by well design interference effect inside of multilayer films to get the super-dispersion. The positive and negative spatial dispersion are existed in side of coatings, and is very sensitive to the angle of incident and wavelength. The analysis methods and the different kinds of spatial dispersion thin film filter devices and tunable spatial dispersion filter devices are presented in the paper.
Subwavelength Dichroic Demultiplexer Based on Double Fabry-Perot Cavities.

Feng LI,Zhen-Yu Yang,Jun-Jun Shi,Xiao-Bo He

DOI: https://doi.org/10.1364/oe.472582

IF: 3.8

2022-01-01

Optics Express

Abstract:Plasmonic demultiplexers hold promise for the realization of the subwavelength and high-splitting ratio dichroic splitter and have a wide range of applications from optical communication, and manipulation to ultrafast data treatment. However, this vision has not been realized for a long time due to lacking the suitable splitting structure design, which limits its further development of integrated photonic circuits. Here, we demonstrate a plasmonic demultiplexer with subwavelength feature size (0.54 µm) and broadband spectral (620-870 nm) range, and high-splitting ratio (17 dB in experiments and 20 dB in calculations). It consists of two adjacent Fabry-Perot cavities (covered by PMMA polymer) and coupling gratings, which are integrated with the Au waveguide. The relatively simple double cavities design of our device has a simple theoretical analysis and fabrication process. Our work has relevance for various optical applications, such as multiple wavelength photodetectors and optical multichannel interconnects.
Trichroic prism assembly for separating and recombining colors in a compact projection display

Hoi-Sing Kwok,Po-Wing Cheng,Ho-Chi Huang,Hai-Feng Li,Zhen-Rong Zheng,Pei-Fu Gu,Xu Liu

DOI: https://doi.org/10.1364/AO.39.000168

IF: 1.9

2000-01-01

Applied Optics

Abstract:A trichroic prism assembly design, believed to be new, is proposed and demonstrated. This new design has the advantages of low s- and p-polarization dependence in the reflectance spectra of the optical coatings. Hence it can be used for both color separation and color recombination with polarization. change. This new trichroic prism assembly is especially useful in a compact color projector employing reflective liquid-crystal light valves. (C) 2000 Optical Society of America OCIS codes: 220.4830 230.3720, 330.1690.
Silicon-on-Insulator-Based Compact Optical Demultiplexer Employing Etched Diffraction Grating

WH Wang,YZ Tang,YX Wang,HC Qu,YM Wu,T Li,JY Yang,YL Wang,M Liu

DOI: https://doi.org/10.1088/0256-307x/21/7/022

2004-01-01

Abstract:A compact optical demultiplexer with etched diffraction grating (EDG) is designed and fabricated on a silicon-on-insulator (SOI) material. Several 90degrees turning mirrors are used to bend the waveguides, and the size of the EDG-based demultiplexer is minimized to only 16 x 1.7 mm(2). The crosstalk is about -18 dB. The on-chip loss is about 18.2 dB, which is composed of about 16.9 dB excess loss and 1.3 dB diffraction loss. Measures to improve the performance are discussed.
Silicon-on-insulator-based Optical Demultiplexer Employing Turning-Mirror-integrated Arrayed-Waveguide Grating

KM Jia,WH Wang,YZ Tang,YR Yang,JY Yang,XQ Jiang,YM Wu,MH Wang,YL Wang

DOI: https://doi.org/10.1109/lpt.2004.839394

IF: 2.6

2005-01-01

IEEE Photonics Technology Letters

Abstract:In this letter, we demonstrate an optical demultiplexer on the silicon-on-insulator material employing the turning-mirror-integrated arrayed-waveguide grating (AWG). We substitute the bent waveguide array in the traditional AWG configuration by adopting the structure of the turning-mirror-integrated straight waveguides. Description of the design procedure is provided. The crosstalk of the fabricated 1/spl times/4 AWG is better than -23.1 dB. The typical on-chip insertion loss is about -8 dB and the output nonuniformity is less than 0.4 dB. The polarization-dependent central wavelength shift is about 0.068 nm.
A Novel 2 X 3 Optical Switch Utilizing Total Internal Reflection Based On Thermo-Optical Effect Of Polymer

Hui Yu,Xiaoqing Jiang,Jianyi Yang,Minghua Wang

DOI: https://doi.org/10.1117/12.667008

2006-01-01

Abstract:An ultra compact, highly integrated photonic switch with 2 x 3 configuration was designed and fabricated using the thermo-optical effect of polymer materials. By exerting voltage to proper compartment of the electrode, the input light can be switched freely among three output ports. The experiment results show: for the "insufficient reflection" state, the extinction ratio is 16.64dB for the middle output port; for the "bat" state, the extinction ratio for the reflection port is 26.8 dB. The power consumption is on the scale of 100 mW, and varies with different function mode.
Experimental Demonstration Of Two-Dimensional Multimode-Interference Optical Power Splitter

Yl Sun,Xq Jiang,Jy Yang,Y Tang,Mh Wang

DOI: https://doi.org/10.1088/0256-307x/20/12/027

2003-01-01

Chinese Physics Letters

Abstract:A two-dimensional multimode-interference optical power splitter is designed and demonstrated. The new device can be used for the optical power splitting in two transverse directions. Silicon-on-insulator technology is utilized to fabricate the device. The performance of the device is tested.
Thin-film polarizing beam splitters used in liquid crystal projection display

Yi Ding,Peifu Gu,SUN Xu-tao,Zhenrong Zheng,Yueguang Zhang,LI Hai-feng

DOI: https://doi.org/10.3785/j.issn.1008-973X.2009.08.015

2009-01-01

Abstract:In order to improve the energy efficiency and image contrast of liquid crystal display(LCD) projector,a wide-angle and broadband optical thin-film polarizing beam splitter(PBS) was designed.Several thin-film materials was adopted to achieve multi-kinds of Brewster's angles.The number and thickness of the films were optimized to obtain the wide-angle and broadband PBS.Using SF57 and SF2 glasses as prism materials,and TiO 2,Ta 2O 5,Al 2O 3,SiO 2 as film materials,four typical PBS multi-layer designs were given based on the above principle and the automatic Needle design method.The layer number of the optimized thin-film is 50～60,and the incident angle in air for the PBS reaches ±10.5°.The measured results showed that the integrated transmittance of P-polarization was 88.0% and 93.4% respectively at wavelength of 420—460 nm and 460—680 nm as well as that of S-polarization was 0.095% at wavelength of 420—680 nm.The PBS can be applied to F/2.8 optical systems to improve their performance obviously.
Multiplexer/demultiplexer in Optical Communications Based on Holographic Fresnel Lens

XC Ren,S Liu,XS Zhang,SS Li

DOI: https://doi.org/10.1117/12.635273

2005-01-01

Abstract:Multiplexer/demultiplexer for WDM system based on off-axis holographic Fresnel lens was fabricated. The principle and fabricating technology of the demultiplexer with the central working wavelength of 1310 nm and the channel spacing of 25 nm were described. The reduction of third-order aberrations was the main consideration. The theoretical analysis indicates that third-order aberration can be effectively reduced if the condition tanαC/tanαR=-λC/λO is applied in geometry design and long object distance is selected. The experiment method and results were presented in this paper, and results verified the theoretical analysis.
Realization of an Economical Polymer Optical Fiber Demultiplexer

Ulrich H. P. Fischer,Matthias Haupt,Christian Reinboth,Ulrich H.P. Fischer

DOI: https://doi.org/10.48550/arXiv.0705.3964

2007-05-27

Optics

Abstract:Polymer Optical Fiber (POF) can be and are being used in various fields of applications. Two of the main fields are the automotive and the home entertainment sector. The POF can be applied in several different optical communication systems as automotive multi-media busses or in-house Ethernet systems. The requirements of bandwidth are increasing very fast in these sectors and therefore solutions that satisfy these demands are of high actuality. One solution is to use the wavelength division multiplexing (WDM) technique. Here, several different wavelengths can carry information over one POF fiber. All wavelengths that are transmitted over the fiber, must be separated at the receiver to regain and redirect the information channels. These separators are so-called Demultiplexers. There are several systems available on the market, which are all afflicted with certain disadvantages. But all these solutions have one main disadvantage, they are all too expensive for most of the applications mentioned above. So the goal of this study is to develop an economical Demultiplexer for WDM transmission over POF. The main idea is to separate the chromatic light in its monochromatic components with the help of a prism with low reciprocal dispersive power. The prism and the other assemblies, which are needed to adjust the optical path, should be manufactured in injection molding technique. This manufacturing technique is a very simple and economical way to produce a mass production applicable Demultiplexer for POF.
Design and experimental demonstration of a silicon multi-dimensional (de)multiplexer for wavelength-, mode- and polarization-division (de)multiplexing.

Yu He,Yong Zhang,Hongwei Wang,Lu Sun,Yikai Su

DOI: https://doi.org/10.1364/OL.390015

IF: 3.6

2020-01-01

Optics Letters

Abstract:Leveraging the physical dimensions of an optical carrier (e.g., wavelength, mode, or polarization) allows significant scaling of the transmission capacity for optical communications. Here we propose a scheme for implementing on-chip silicon (de)multiplexers with simultaneous wavelength-, mode-, and polarization-division (de)multiplexing capability. The device is constructed by using cascaded subwavelength grating (SWG)-based contra-directional couplers. To verify the feasibility of the proposed structure, we perform a proof-of-concept experiment of an 8-channel (de)multiplexer with two wavelengths, two modes, and two polarizations. The insertion losses are lower than 6.6 dB and the crosstalk values are below 18.7 dB at around 1540 nm and 1550 nm for all the eight channels. (C) 2020 Optical Society of America.

An Available Optical Thin Film Demultiplexer Based on Superprism Effect

Design of High-Level Reflectivity Thin Film Spatial Demultiplexer

Tunable spatial demultiplexer based on the Fabry-Perot filter.

Studies on Superprism Effects in Multilayer Thin Film Stacks

Enhanced superprism effect based on positive/negative lateral shift of reflective beam in a Fabry-Perot filter.

Superprism effect with a large spatial dispersion and high efficiency in a reflection filter

Investigation of Multichannel Spatial Demultiplexer Based on Thickness-Tapered Thin Film Stacks

Color-Separation Multilayer Systems Used for Thin Film Transistor-Liquid Crystal Display

Superprism Effect in Thin Film Fabry-Perot Filter

Based 0n High-Level Reflectivity Thin Film Spatial Demultiplexer Research

Spatial Dispersion of Optical Thin Films

Subwavelength Dichroic Demultiplexer Based on Double Fabry-Perot Cavities.

Trichroic prism assembly for separating and recombining colors in a compact projection display

Silicon-on-Insulator-Based Compact Optical Demultiplexer Employing Etched Diffraction Grating

Silicon-on-insulator-based Optical Demultiplexer Employing Turning-Mirror-integrated Arrayed-Waveguide Grating

A Novel 2 X 3 Optical Switch Utilizing Total Internal Reflection Based On Thermo-Optical Effect Of Polymer

Experimental Demonstration Of Two-Dimensional Multimode-Interference Optical Power Splitter

Thin-film polarizing beam splitters used in liquid crystal projection display

Multiplexer/demultiplexer in Optical Communications Based on Holographic Fresnel Lens

Realization of an Economical Polymer Optical Fiber Demultiplexer

Design and experimental demonstration of a silicon multi-dimensional (de)multiplexer for wavelength-, mode- and polarization-division (de)multiplexing.