Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

High Efficiency Inverted Polymer Solar Cells With Room-Temperature Titanium Oxide/Polyethylenimine Films As Electron Transport Layers

Versatile Device Architectures for High-Performing Light-Soaking-Free Inverted Polymer Solar Cells

Room-temperature processed TiO2 to construct composite electron transport layers for efficient planar perovskite solar cells

Light-Soaking-Free Inverted Polymer Solar Cells with an Efficiency of 10.5% by Compositional and Surface Modifications to a Low-Temperature-Processed TiO 2 Electron-Transport Layer.

A dithieno[3,2- a :3′,2′- j ][5,6,11,12]chrysene diimide based polymer as an electron transport layer for efficient inverted perovskite solar cells

Highly efficient inverted polymer solar cells based on ethanolamine-treated indium tin oxide as cathode

Enhancing performance of inverted polymer solar cells by an effective novel double layer combining MoO3 and PEIE

Efficient and stable inverted perovskite solar cells enabled by homogenized PCBM with enhanced electron transport

Highly Efficient Polymer Tandem Cells and Semitransparent Cells for Solar Energy

Enhanced Stability and Performance of Inverted Perovskite Solar Cell Using Titanium Interlayer

Dramatic improvement in the stability and mechanism of high-performance inverted polymer solar cells featuring a solution-processed buffer layer

Room‐Temperature‐Processed Fullerene/TiO 2 Nanocomposite Electron Transporting Layer for High‐Efficiency Rigid and Flexible Planar Perovskite Solar Cells

High-Performance Inverted Perovskite Solar Cells by Reducing Electron Capture Region for Electron Transport Layers

P3HT‐Based Polymer Solar Cells with 8.25% Efficiency Enabled by a Matched Molecular Acceptor and Smart Green‐Solvent Processing Technology

High-performance inverted polymer solar cells: Device characterization, optical modeling, and hole-transporting modifications

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Surpassing 13% Efficiency for Polythiophene Organic Solar Cells Processed from Nonhalogenated Solvent

Hybrid Solar Cells Using Solution-Processed TiO2/Sb2S3 Bilayer As Electron Transport Layer

Understanding the PEDOT:PSS, PTAA and P3CT-X Hole-Transport-Layer-Based Inverted Perovskite Solar Cells

A Multilayered Electron Extracting System for Efficient Perovskite Solar Cells

Enhanced Efficiency Of Polymer: Fullerene Bulk Heterojunction Solar Cells With The Insertion Of Thin Tio2