Abstract:In this paper Ethylene Propylene Diene Monomer rubber (EPDM) foams were filled with different amounts of paraffin, a common phase change material (PCM) having a melting temperature at about 70 °C, to develop novel rubber foams with thermal energy storage (TES) capabilities. Samples were prepared by melt compounding and hot pressing, and the effects of three foaming methods were investigated. In particular, two series of samples were produced through conventional foaming techniques, involving physical (Micropearl® F82, MP, Lehvoss Italia s.r.l. Saronno, Italia) and chemical (Hostatron® P0168, H, Clariant GmbH, Ahrensburg, Germany) blowing agents, while the salt leaching method was adopted to produce another series of foams. Scanning electron microscopy (SEM) and density measurements showed that MP led to the formation of a closed-cell porosity, while a mixed closed-cell/open-cell morphology was detected for the H foamed samples. On the other hand, foams produced through salt leaching were mainly characterized by an open-cell porosity. The qualitative analysis of paraffin leakage revealed that at 90 °C only the foams produced through salt leaching suffered from significant PCM leakage. Consequently, the thermo-mechanical properties were investigated only in samples produced with H and MP. Differential Scanning Calorimetry (DSC) analysis revealed that EPDM/paraffin foams were endowed by good TES properties, especially at higher PCM contents (up to 145 J/g with a paraffin amount of 60 wt%). Tensile and compressive tests demonstrated the addition of the PCM increased the stiffness at 25 °C, while the opposite effect was observed above the melting temperature of paraffin. These results suggest that the EPDM foams produced with H and MP show an interesting potential for thermal management of electronic devices.

Experiment Research on the Mechanical Performance of Epdm Insulation Pyrolysis Process

Relationships Between Thermo-Oxidation and Dynamic Rheological Behavior of Epdm

Mechanical Properties and Thermal Behaviors of Dynamically Photocrosslinked PP/EPDM Blends

Dielectric Loss of EPDM Insulation Subjected to Thermal Stress and Pressure

The Effect of Thermal Aging on the Mechanical Properties of Ethylene Propylene Diene Monomer Charge Coating

Investigations on the Morphological, Mechanical, Ablative, Physical, Thermal, and Electrical Properties of EPDM-Based Composites for the Exploration of Enhanced Thermal Insulation Potential

Preparation and Mechanical Properties Analysis of Rare Earth Filling Ethylene‐Allene Monomer Rubber Composite

Mechanical properties, morphological structure, and thermal behavior of dynamically photocrosslinked PP/EPDM blends

Mechanical properties and structural characteristics of dynamically photocrosslinked PP/EPDM blends

Silicon Hybrid EPDM Composite with High Thermal Protection Performance

Experimental Study on the Surface Pyrolysis Properties and Modeling of Expanded Polystyrene

Mechanical properties and morphological structures of short glass fiber reinforced PP/EPDM composite

Thermo-Mechanical Behavior of Novel EPDM Foams Containing a Phase Change Material for Thermal Energy Storage Applications

Effects of difunctional reactive polyhedral oligomeric silsesquioxane on the properties of EPDM

Ageing behaviour and molecular/network structure evolution of EPDM/carbon black composites under compression and in thermal-oxidative environments

Dynamically photocrosslinking of polypropylene/EPDM blends as a thermoplastic elastomer

Study on the performance and application of EPDM by regression analysis method

Research on the Thermal Aging Performance of a GAP-Based Polyurethane Elastomer

Preparation and Flammability of Epdm/Pp/Mg(Oh)(2) Dynamic Vulcanizates

A thermally reversible healing EPDM based elastomer with higher tensile properties and damping properties

Photo- and Thermo-Oxidative Degradation of Photocrosslinked Ethylene–propylene–diene Terpolymer