Different Cell and Tissue Behavior of Micro-/Nano-Tubes and Micro-/Nano-Nets Topographies on Selective Laser Melting Titanium to Enhance Osseointegration
Xiaoran Yu,Ruogu Xu,Zhengchuan Zhang,Qiming Jiang,Yun Liu,Xiaolin Yu,Feilong Deng
DOI: https://doi.org/10.2147/IJN.S303770
IF: 7.033
2021-05-14
International Journal of Nanomedicine
Abstract:Xiaoran Yu, 1, 2, * Ruogu Xu, 1, 2, * Zhengchuan Zhang, 1, 2 Qiming Jiang, 1, 2 Yun Liu, 1, 2 Xiaolin Yu, 1, 2 Feilong Deng 1, 2 1 Department of Oral Implantology, Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-Sen University, Guangzhou, Guangdong, 510055, People's Republic of China; 2 Guangdong Provincial Key Laboratory of Stomatology, Guangzhou, Guangdong, 510080, People's Republic of China *These authors contributed equally to this work Correspondence: Feilong Deng; Xiaolin Yu Department of Oral Implantology, Hospital of Stomatology, Guanghua School of Stomatology, Sun Yat-Sen University, No. 56, Ling Yuan Xi Road, Guangzhou, 510055, People's Republic of China Tel +86 20 83862537 Fax +86 20 83822807 Email ; Background and Purpose: Micro-/nano-tubes (TNTs) and micro-/nano-nets (TNNs) are the common and sensible choice in the first step of combined modifications of titanium surface for further functionalization in the purpose of extended indications and therapeutic effect. It is important to recognize the respective biologic reactions of these two substrates for guiding a biologically based first-step selection. Materials and Methods: TNTs were produced by anodic oxidation and TNNs were formed by alkali-heat treatment. The original selective laser melting (SLM) titanium surface was set as control. Surface characterization was evaluated by scanning electron microscopy, surface roughness, and water contact angle measurements. Osteoclastogenesis and osteogenesis were measured. MC3T3-E1 cells and RAW 264.7 cells were used for in vitro assay in terms of adhesion, proliferation, and differentiation. In vivo assessments were taken on Beagle dogs with micro-CT and histological analysis. Results: TNN and TNT groups performed decreased roughness and increased hydrophilicity compared with SLM group. For biological detections, the highest ALP activity and osteogenesis-related genes expression were observed in TNT group followed by TNN group (P < 0.05). Interestingly, when it comes to the osteoclastogenesis, TNNs displayed lowest TRAP activity and osteoclastogenesis-related genes expression and TNTs were lower than SLM but higher than TNNs (P < 0.05). BV/TV around implants was highest in TNT group after 4 weeks (P < 0.05). HE, ALP and TRAP staining showed that osteogenic and osteoclastic activity around TNTs were both higher than TNNs (P < 0.05). Conclusion: TNNs and TNTs have dual advantages in promotion of osteogenesis and inhibition of osteoclastogenesis. Furthermore, TNNs showed better capability in inhibiting osteoclast activity while TNTs facilitated stronger osteogenesis. Our results implied that TNT substrates would take advantage in early application after implantation, while diseases with inappropriate osteoclast activity would prefer TNN substrates, which will guide a biologically based first-step selection on combined modification for different clinical purposes. Keywords: multifunctional surface modifications, osteoclastogenesis, osteogenesis, custom-made titanium bone substitutes Nowadays, accuracy, flexibility, and speed as well as minimizing waste have become the emphases in manufacturing processes which promote the rapid development of three-dimensional (3D) printing. As a result, a wide range of material types such as metals, ceramics and polymers have been successfully manufactured by 3D printing with desirable features. 1–4 Selective laser melting (SLM) is one of the prolific powder-bed based 3D printing technologies for metals. Through a layer-by-layer manufacturing method, SLM is capable of fabricating irregular and complex structures with high accuracy and shows huge potential in biomedical applications. 5 , 6 Recently, researchers have reported custom-made titanium bone substitutes created by SLM with several advantages in manufacture. 7–10 Furthermore, for biomedical applications, the custom-made titanium bone substitutes should also possess special biological advantages for extended indications or therapeutic effect such as biomolecule or drug delivery. For example, Lee et al. reported a nanoparticle mediated PPARγ gene delivery on implants could be used as therapeutic dental implants for diabetic patients. 11 Zhang et al. reported that rhPDGF-BB loaded in nano-tube arrays could potentially be used in dental and orthopedic applications for osteoporotic pa -Abstract Truncated-
pharmacology & pharmacy,nanoscience & nanotechnology