Abstract:Due to the advantages of low cost, easy fabrication, mechanical flexibility, the research on organic solar cells has attracted a lot of attentions in the last decades. Among countless organic materials, the most successful ones are conjugated polymers, which were widely used in bulk heterojunction (BHJ) in conjugation with the fullerene [1]. In view of the fact the interpenetratedphase-separated p-n composites offer more chances for excitons to reach the p-n interfaces, BHJ greatly facilitates the dissociation of photogenerated excitons before decaying to ground state. During exciton dissociation process, the exciton delocalization at an ultra fast timescale has been observed recently, which has considerable effects on the charge generation and device performance. In this work, based on the recent studies [2–4], we established a theoretical model of polymer solar cells (PSCs) incorporating the exciton delocalization process. Through the model, we found the increase of delocalized excitons (compared to the total generated excitons) will significantly improve the short-circuit current, open-circuit voltage, fill factor and power conversion efficiency of PSCs. Particularly, the saturations of fill factor and open-circuit voltage are also observed, and the saturation points depend on the active layer thickness and recombination rate. For instance,the device model of 200nm thickness active layer has the saturated fill factor at 70% delocalization ratio, which is close to the conventional ratio of practical devices. The device configuration studied comprises a BHJ active layer sandwiched between a transparent anode and a metal cathode. Moreover, the active material is a mixture of OC 1 C 10 -PPV, as the donor, and PCBM, as the acceptor [5]. The generation rate of excitons is assumed to be homogeneous. The model proposed involves both the drift-diffusion model for photocarriers (Eq. (1)) and the diffusion and dissociation model for excitons (Eq. (2)). The governing equations are given as follows equation where q is elementary charge, n(p) is the electron (hole) density, and r G , r R are the parametersfor controlling exciton generation and bulk recombination, respectively. E is the internal E-field. µ and D are the mobility and diffusion coefficients. The exciton density is denoted by X diff and k diss is the exciton dissociation rate. The recombination R is taken to be a bimolecular form,with the rate given by Langevin [6], and η s is 0.25 for the singlet excitons. Using the physical parameters given by experiments [5], the nonlinear governing equation sets are solved self-consistently. The excitons are delocalized at an ultra fast timescale to form electron-hole pairs, which is much faster than the photo carrier relaxation time and exciton diffusion time. Consequently, the delocalization process was simulated by directly inserting the delocalization ratio η del into the equations.

Optical Modelling of a Double Heterojunction Polymer Photovoltaic Cell with Triterminal Tandem Structure

The Role Of Exciton Delocalization In The Performance Of Bulk-Heterojunction Polymer Solar Cells

Perovskite/Colloidal Quantum Dot Tandem Solar Cells: Theoretical Modeling and Monolithic Structure

High-Efficiency Triple-Junction Polymer Solar Cell: A Theoretical Approach

Systematic Investigation of Benzodithiophene- and Diketopyrrolopyrrole-Based Low-Bandgap Polymers Designed for Single Junction and Tandem Polymer Solar Cells

Optimization of all-polymer/Sb2Se3 tandem solar cells for enhanced efficiency: a comprehensive TCAD modeling approach

Achieving High Performance Tandem Polymer Solar Cells

An Efficient Triple-Junction Polymer Solar Cell Having A Power Conversion Efficiency Exceeding 11%

Optical Design of Monolithic Two-Terminal Perovskite/Si Tandem Solar Cells for Efficient Photon Management

PCDTBT8‐Doped PffBT4T‐2OD‐Based Ternary Solar Cells with Enhanced Open‐Circuit Voltage, Fill Factor, and Charge Separation Efficiency

A material combination principle for highly efficient polymer solar cells investigated by mesoscopic phase heterogeneity.

High Efficiency Non-fullerene Organic Tandem Photovoltaics Based on Ternary Blend Subcells

Simple Tandem Organic Photovoltaic Cells for Improved Energy Conversion Efficiency

Dual Förster resonance energy transfer and morphology control to boost the power conversion efficiency of all-polymer OPVs

Bifacial Si Heterojunction-Perovskite Organic-Inorganic Tandem to Produce Highly Efficient Solar Cell

All-Organic Tunnel Junctions As Connecting Units In Tandem Organic Solar Cell

Insights into Excitonic Dynamics of Terpolymer-Based High-Efficiency Nonfullerene Polymer Solar Cells: Enhancing the Yield of Charge Separation States.

Combining Energy Transfer and Optimized Morphology for Highly Efficient Ternary Polymer Solar Cells

Modelling of Organic Nanograting Heterojunctions for Photoelectric Conversion

Hybrid Tandem Solar Cell Enhanced by a Metallic Hole-Array As the Intermediate Electrode.

Tandem polymer solar cells featuring a spectrally matched low-bandgap polymer