11. Full solar spectrum conversion via multi-junction architectures and optical concentration
Yuan Yao,Lu Xu,X. Sheng,Noah D Bronstein,J. Rogers,A. Alivisatos,R. Nuzzo
2016-01-01
Abstract:Status Significant advances have been made in research to improve the performance of single-junction PV devices. Currently, the best Si and GaAs devices have achieved efficiencies of 25.6% and 28.8%, respectively [26] (see sections 2, 4). The realization of significant further enhancements in the efficiencies of PV energy conversion, however, resorts to MJ architectures using semiconductor materials with subcell band gaps tuned to target different portions of the solar spectrum in order to minimize carrier thermalization losses and to increase spectrum coverage to exceed the SQ limit [24]. In theory, a MJ cell can achieve an efficiency as high as 86.8% with an infinite number of junctions [107] (a value lower than the Landsberg limit [21] due to entropy losses), and a number of different cell designs have been intensively explored by the PV research community as a means through which such forms of performance enhancement can be realized. These include, most notably, devices that embed the semiconductor elements in the form of MJ SC stacks [108] and, to a lesser degree, optical approaches involving various forms of spectrum splitting [109] (see also section 13). In the first design, the subcells are either epitaxially or mechanically stacked together in the order of decreasing band gaps to divide the incident sunlight using the absorption of the subcells (see also section 3). In the second approach, separate optics (e.g., prisms, holograms, and dielectric bandpass filters) are used to split the solar spectrum and to direct different portions to the relevant subcell. It has been persuasively argued that both designs would benefit from high geometric concentration of the solar irradiance as one means to both offset the high material costs encumbered by the III–V semiconductor device elements and to enhance the system power-conversion efficiency. To date, cell stacking designs have achieved the highest benchmark performances in solar energy conversion with world-record efficiencies of MJ cells reaching 46.0% with a four-junction design (InGap/ GaAs/GaInAsP/GaInAs) under 508 suns [26]. Exemplary recent progress includes a report from our group of 43.9% efficient quadruple-junction four-terminal microscale SCs that were fabricated by mechanical stacking of a top 3-J device onto a bottom Ge cell via transfer-printing-based assembly [110]. Current and future challenges For epitaxially grown MJ devices, the difficulty of sustaining lattice matching through multiple layers of growth limits the material selections that are available for use in each subcell and, thus, directly restricts achievable limits for device performance. Mechanically stacked devices, on the other hand, can be fabricated via high-temperature wafer bonding [111] to circumvent this issue but still carries a requirement for current matching at the electrically conducting interfaces, which is difficult to realize as the number of subcells increases to subdivide the solar spectrum. Alternatively, insulating adhesives can be used between mechanically stacked subcells to enable multiterminal connections and, in this way, to avoid the need for current matching. These interfaces need to be carefully designed to minimize reflection losses as well as to manage heat flow and thermal-mechanical stresses at high optical concentration [110]. Additional electro-optical challenges exist for the material used in each subcell. For example, a top wide-band-gap subcell (i.e., Eg>1.4 ev) generally cannot be doped to a sufficiently high level to enable efficient carrier collection under high-irradiance concentration; it requires incorporation of highly doped lowband-gap materials that either degrade its optical transparency for low-energy photons or complicate backcontact grid configurations [108]. It has been noted that the limitations associated with stacked MJ devices can be tackled, in principle, by employing external optical components to split and to distribute the solar radiation to an array of spatially separated subcells [112]. By decoupling material compatibility from band-gap optimization, this approach also enables MJ designs with larger numbers of subcells and, thus, higher theoretical efficiencies. As the cell fabrication steps are reduced to provide a set of single-junction devices, simplified process flows for the semiconductor components are possible (see sections 2, 7). The commonly proposed optical designs include holographic gratings and wavelength-selective mirrors (e.g., multilayer dielectric Bragg stacks). Their practical use, however, is hindered by the formidable requirements for high-optical quality as well as the complexity of the optical designs needed to achieve competitive system-level efficiencies. The high cost of III–V materials, especially in MJ cell contexts, likely necessitates a high-optical-concentration design to achieve commercial viability (see section 12). Optical losses figure importantly in all forms of concentrator PV designs. Stacked cells, for example, are subject to significant Fresnel losses (e.g., 12% of incident photons are lost to reflection before reaching the SCs for a system with three glass/air interfaces) that limit their optical (and, thus, powerconversion) efficiencies. Broadband antireflection (AR) coatings would afford an ideal solution, but materials that can span the refractive index range needed to mitigate these effects have yet to be developed. The use of common lighttrapping designs on the PV cells also become more complex as they can scatter light and, otherwise, limit the broadspectrum performance of high-concentration optics (see section 3). Geometric solar concentrators (GSCs) also require