Optimal Characteristic Nanosizes of Mineral Bridges in Mollusk Nacre

Yue Shao,Hong-Ping Zhao,Xi-Qiao Feng

DOI: https://doi.org/10.1039/c4ra04902k

IF: 4.036

2014-01-01

RSC Advances

Abstract:The nanosizes of mineral bridges linking neighboring platelets in various types of mollusk nacre dictate the optimal interfacial strength.

What problem does this paper attempt to address?

Nanostructured individual nacre tablet: a subtle designed organic–inorganic composite

shengnan wang,xinqiao zhu,xiaohui yan,jingfei deng,rizhi wang,xiaoxiang wang

DOI: https://doi.org/10.1039/c4ce02308k

IF: 3.756

2015-01-01

CrystEngComm

Abstract:From natural evolution, nacre, a biogenic organic-inorganic composite, fulfils an ingenious combination of remarkable strength and toughness. Its basic building block, the individual nacre tablet, assumes an important mechanical function. Unravelling its design strategies can hence provide essential information for the pursuit of high-performance artificial composites. Here, the nanostructure inside the individual nacre tablet (Pinctada maxima) was investigated using transmission electron microscopy techniques. Results show that organic matter is trapped inside the tablet in both an islet-like and sheet-like manner. More interestingly, the crystal structure of aragonite scaffold is continuous and homodromous throughout the whole tablet even in this case. A biomineralization mechanism of the tablet is discussed based on this finding.
A Microstructural Study of Individual Nacre Tablet of Pinctada Maxima

Sheng-Nan Wang,Xiao-Hui Yan,Rizhi Wang,Da-Hui Yu,Xiao-Xiang Wang

DOI: https://doi.org/10.1016/j.jsb.2013.07.013

IF: 3.234

2013-01-01

Journal of Structural Biology

Abstract:Nacre tablets from the shell of Pinctada maxima were studied with SEM, TEM and STEM. The systematic nanolath morphology on the (001) surface of nacre tablets was observed after acidic etching and mechanical polishing. The nanolaths were along the [100] crystallographic orientation of aragonite crystal. The (010) and (100) cross section surfaces of the nacre tablets showed nanolath and nanograin morphologies, respectively, which was consistent with [100] crystallographic orientation of nanolath on the (001) surface. Sheet-like defects with low mass density were observed on the (001) plane inside nacre tablets and were considered to be the cause of nanolath morphology revealed on the surfaces by acidic etching and mechanical polishing. On the other hand, large block [110] twins that divide the nacre tablets into two sectors were identified. The implication of these twins on the understanding to the crystallization mechanism of nacre tablets was discussed.
Damage-Tolerance Strategies for Nacre Tablets

Shengnan Wang,Xinqiao Zhu,Qiyang Li,Rizhi Wang,Xiaoxiang Wang

DOI: https://doi.org/10.1016/j.jsb.2016.02.017

IF: 3.234

2016-01-01

Journal of Structural Biology

Abstract:Nacre, a natural armor, exhibits prominent penetration resistance against predatory attacks. Unraveling its hierarchical toughening mechanisms and damage-tolerance design strategies may provide significant inspiration for the pursuit of high-performance artificial armors. In this work, relationships between the structure and mechanical performance of nacre were investigated. The results show that other than their brick-and-mortar structure, individual nacre tablets significantly contribute to the damage localization of nacre. Affected by intracrystalline organics, the tablets exhibit a unique fracture behavior. The synergistic action of the nanoscale deformation mechanisms increases the energy dissipation efficiency of the tablets and contributes to the preservation of the structural and functional integrity of the shell.
Arrangement of Intra-Crystalline Organic Matrix in Nacre from Red Abalone: A View by High-Resolution Synchrotron Powder Diffraction Combined with SEM Observation

Xiao-Hui Yan,Sheng-Nan Wang,Xiao-Juan Zhang,Xiao-Xiang Wang,Rizhi Wang

DOI: https://doi.org/10.1039/c1ce05766a

IF: 3.756

2011-01-01

CrystEngComm

Abstract:In the present study, we combine high-resolution synchrotron powder diffraction with SEM to shed additional light on the arrangement of an intra-crystalline organic matrix in the nacre from red abalone. SEM observation and synchrotron diffraction analysis show that an intra-crystalline organic matrix exists inside nacre tablets and is adsorbed on the (002) atomic plane in an isolated form. Most probably, the intra-crystalline organic matrix is nacrein and its atomic groups are connected with the (012) atomic plane. The findings provide a new understanding of the arrangement of intra-crystalline organic matrices and may facilitate studies on the formation mechanism and the strengthening and toughening mechanism of the nacre. It is worth pointing out that the new experimental method in this present paper can be extended to nanostructural research of other biominerals.
Discontinuous crack-bridging model for fracture toughness analysis of nacre

Yue Shao,HongPing Zhao,Xiqiao Feng,Huajian Gao

DOI: https://doi.org/10.1016/j.jmps.2012.04.011

IF: 5.582

2012-01-01

Journal of the Mechanics and Physics of Solids

Abstract:Studying the structure–property relation of biological materials can not only provide insight into the physical mechanisms underlying their superior properties and functions but also benefit the design and fabrication of advanced biomimetic materials. In this paper, we present a microstructure-based fracture mechanics model to investigate the toughening effect due to the crack-bridging mechanism of platelets. Our theoretical analysis demonstrates the crucial contribution of this mechanism to the high toughness of nacre. It is found that the fracture toughness of nacre exhibits distinct dependence on the sizes of platelets, and the optimized ranges for the thickness and length of platelets required to achieve higher fracture toughness are given. In addition, the effects of such factors as the mechanical properties of the organic phase (or interfaces), the effective elastic modulus of nacre, and the stacking pattern of platelets are also examined. Finally, some guidelines for the biomimetic design of novel materials are proposed based on our theoretical analysis.
On Flaw Tolerance of Nacre: a Theoretical Study.

Yue Shao,Hong-Ping Zhao,Xi-Qiao Feng

DOI: https://doi.org/10.1098/rsif.2013.1016

IF: 4.293

2014-01-01

Journal of The Royal Society Interface

Abstract:As a natural composite, nacre has an elegant staggered 'brick-and-mortar' microstructure consisting of mineral platelets glued by organic macromolecules, which endows the material with superior mechanical properties to achieve its biological functions. In this paper, a microstructure-based crack-bridging model is employed to investigate how the strength of nacre is affected by pre-existing structural defects. Our analysis demonstrates that owing to its special microstructure and the toughening effect of platelets, nacre has a superior flaw-tolerance feature. The maximal crack size that does not evidently reduce the tensile strength of nacre is up to tens of micrometres, about three orders higher than that of pure aragonite. Through dimensional analysis, a non-dimensional parameter is proposed to quantify the flaw-tolerance ability of nacreous materials in a wide range of structural parameters. This study provides us some inspirations for optimal design of advanced biomimetic composites.
Optimization Design of Strong and Tough Nacreous Nanocomposites Through Tuning Characteristic Lengths

Yong Ni,Zhaoqiang Song,Hongyuan Jiang,Shu-Hong Yu,Linghui He

DOI: https://doi.org/10.1016/j.jmps.2015.04.013

IF: 5.582

2015-01-01

Journal of the Mechanics and Physics of Solids

Abstract:How nacreous nanocomposites with optimal combinations of stiffness, strength and toughness depend on constituent property and microstructure parameters is studied using a nonlinear shear-lag model. We show that the interfacial elasto-plasticity and the overlapping length between bricks dependent on the brick size and brick staggering mode significantly affect the nonuniformity of the shear stress, the stress-transfer efficiency and thus the failure path. There are two characteristic lengths at which the strength and toughness are optimized respectively. Simultaneous optimization of the strength and toughness is achieved by matching these lengths as close as possible in the nacreous nanocomposite with regularly staggered brick-and-mortar (BM) structure where simultaneous uniform failures of the brick and interface occur. In the randomly staggered BM structure, as the overlapping length is distributed, the nacreous nanocomposite turns the simultaneous uniform failure into progressive interface or brick failure with moderate decrease of the strength and toughness. Specifically there is a parametric range at which the strength and toughness are insensitive to the brick staggering randomness. The obtained results propose a parametric selection guideline based on the length matching for rational design of nacreous nanocomposites. Such guideline explains why nacre is strong and tough while most artificial nacreous nanocomposites aere not.
Mineral Asperities Reinforce Nacre Through Interlocking and Friction-like Sliding

Hao LI,Kun GENG,Bingzhan ZHU,Qiang ZHANG,Yi WEN,Zuoqi ZHANG,Yanan YUAN,Huajian GAO

DOI: https://doi.org/10.1016/j.jmps.2024.105712

IF: 5.582

2024-01-01

Journal of the Mechanics and Physics of Solids

Abstract:While the surface asperities of mineral platelets are widely believed to play important roles in stiffening, strengthening, and toughening nacre, their effects have not been thoroughly investigated. Here, a computationally efficient bar-spring model is adopted to simulate, as platelets with multiple interfacial asperities slide over each other, the tensile force versus elongation behaviors as well as the effective mechanical properties such as modulus, strength, and work-to-fracture in nacre or nacre-like composites. The model employs an effective cohesive law derived from a micromechanical model based on the kinematic and deformation analysis of a single pair of contacting asperities to characterize the traction-separation relationship during the asperity inter-climbing. Strikingly, we find that the mineral asperities and resulting interfacial roughness can elevate the composites’ strength and toughness by up to 2-3 orders of magnitude through a combination of mechanical interlocking and multimodal friction-like mechanisms. Of particular interest is that the asperity-induced strengthening and toughening mechanisms are insensitive to the asperity shapes such as ellipse, hyperbolic cosine, cosine, and parabola. These findings may provide useful guidelines for developing advanced engineering composites with nacre-inspired interface designs.
Analysis of Optimal Crosslink Density and Platelet Size Insensitivity in Graphene-Based Artificial Nacres.

Kaijin Wu,Zhaoqiang Song,Linghui He,Yong Ni

DOI: https://doi.org/10.1039/c7nr06748h

IF: 6.7

2018-01-01

Nanoscale

Abstract:Exploration of graphene-based artificial nacres with excellent mechanical properties demonstrates the potential to surpass natural nacre. Recent experimental studies report that optimal crosslink density defined as concentration of the surface functional groups is usually observed in these artificial nacres towards superb mechanical performance. A hybrid model integrating a nonlinear shear-lag model and atomistic simulations reveals the emergence of an optimal crosslink density at which the maximum strength and toughness are achieved. The origin is due to the balance among the reduction of in-plane tensile properties of the graphene sheets, the enhancement of the shear strength of the interlayer and the reduction of interface plasticity. In addition, our results also reveal that the size insensitivity of the graphene sheet appears when the shear stress of the interlayer is highly localized, the increase of the crosslink density intensifies the nonuniformity of the shear stress and the optimal mechanical properties of the artificial nacre cannot be further enhanced by tuning the size of the graphene sheets. Three kinds of interface molecular interactions with their optimal crosslink densities are also proposed to simultaneously maximize the strength and toughness of graphene-based artificial nacres.
Multi-parameter Structural Optimization to Reconcile Mechanical Conflicts in Nacre-Like Composites

LiChuan Zhou,YinBo Zhu,ZeZhou He,Xu Jin,HengAn Wu

DOI: https://doi.org/10.1016/j.compstruct.2020.113225

IF: 6.3

2021-01-01

Composite Structures

Abstract:Natural nacre exhibits a remarkable combination of high stiffness, strength, and toughness, originating from its ingenious hierarchical staggered structure. However, the conflicts among different mechanical indicators usually have negative effects on improving the comprehensive performance of nacre-like composites. In this study, we develop an optimization approach to determining the optimum structural parameters of nacre-like composites to reconcile mechanical conflicts and achieve desired comprehensive properties by combining theoretical framework and finite element simulation. For regularly staggered model, exact explicit solutions for Young's modulus, strength, and toughness under three different cases of deformation and failure modes are given through rigorous derivations based on brick-and-mortar (BM) microstructure. For randomly staggered model, the mechanical response and failure mechanism are identified through numerical simulation. Parametric studies are conducted to investigate the effects of platelet volume fraction, aspect ratio, and offset ratio on mechanical properties. Using the weighted equation, we achieve the structural optimization with a simultaneous requirement of various mechanical indicators and illustrate the optimum results by ternary diagram. The presented insights should pave the way for optimization design of biomimetic composites for desired mechanical properties.
Interfacial Strength-Controlled Energy Dissipation Mechanism and Optimization in Impact-Resistant Nacreous Structure

Kaijin Wu,Zhijun Zheng,Shuaishuai Zhang,Linghui He,Hongbin Yao,Xinglong Gong,Yong Ni

DOI: https://doi.org/10.1016/j.matdes.2018.12.004

IF: 9.417

2019-01-01

Materials & Design

Abstract:Nacre with a combination of superior strength and toughness is one of the best natural body armors due to its unique brick-and-mortar structure, which is recently regarded as the model system for the lightweight and high impact performance composite design. However, most of the studies of nacreous structure focused on static loadings or simple one-dimensional dynamic load. Our study presents 3D finite element simulation, 3D printing and drop-tower impact testing to reveal the role of interfacial strength and impact velocity in impact resistance of the nacreous structure. An optimal interfacial strength is observed at which the impact resistance reaches a maximum. Sorting of various evolving damage patterns demonstrates that the simultaneous intralayer radial cracks propagation and interlayer delamination lead to a maximal energy dissipation in the presence of the optimal interfacial strength. The phase diagram of damage patterns depending on interfacial strength and impact velocity reveals that the optimal interfacial strength decreases with increasing impact velocity. This study demonstrates that the impact-resistance of nacreous structure under different impact velocities can be enhanced by tuning the interfacial strength, and gives some guidance for advanced protective materials designs.
Maximum Utilization of Nacre-Mimetic Composites by Architecture Manipulation and Interface Modification Towards Critical Damage State

LiChuan Zhou,ZeZhou He,ZhongTing Zhang,YinBo Zhu,HengAn Wu

DOI: https://doi.org/10.1016/j.compscitech.2022.109893

IF: 9.1

2022-01-01

Composites Science and Technology

Abstract:Diverse ultrahigh-strength platelets offer immense promise for high-efficient energy-absorbing design of nacre-mimetic composites. Yet, incompatible interfacial bonding has greatly restricted the pull-out toughening efficiency to a superior level, resulting in insufficient utilization of platelet strength advantages. Herein, we demonstrate an ingenious critical damage state (CDS) control method to utterly exert the energy absorption potential of nacre-mimetics by pursuing the most efficient toughening mode, which is a universal maximum utilization strategy applicable to platelets with arbitrary strengths. Architecture manipulation results suggest that small aspect ratio platelets can generate superb toughness amplification, and stiffening effect is favored for large-size platelets with dense content and high offset ratio, which is consistent with experimental results. More importantly, by identifying the upper limit of shear strength and the lower limit of plastic deformability, we elucidate the interface modification principle imposed on optimized structure to achieve perfect compatibility. Interestingly, we find the uniform staggered pattern is more recommended for superior energy-absorbing design owing to its pronounced strengthening-toughening effect and looser compatibility restriction compared with the random staggered pattern. Furthermore, the proposed CDS control method should not only be generally feasible for nacre-mimetics, but also shed light on other hard/soft layered composite designs targeting utmost synergistic toughening.
Fracture behaviors of nacre-like composites via phase-field fracture modeling

Kai Kang,Yan Chen,Junling Hou,Yilun Liu,Junlin Hou

DOI: https://doi.org/10.1016/j.engfracmech.2023.109837

IF: 5.4

2024-01-05

Engineering Fracture Mechanics

Abstract:Nacre-inspired composites, composed of hard and soft phases, exhibit exceptional combinations of stiffness, strength, and fracture toughness. However, the fracture behaviors of these composites are significantly influenced by the geometric factors and material properties of their constituents. In this study, we systematically investigate the fracture behaviors of nacre-like composites by employing a phase-field fracture model considering the effects of oblique angle between loading and platelet directions, a critical factor often overlooked in previous studies, coupled with the effect of other geometric and material parameters, such as the aspect ratio, Young's modulus and fracture toughness ratio between hard and soft phase. Our findings highlight the significant influence of the oblique angle on the mechanical properties and fracture behaviors of these composites. Particularly, it is found the maximum Young's modulus and strength are obtained when the direction of hard platelet is aligned with the tension direction, while the maximum toughness is achieved at a moderate oblique angle, especially in cases of large aspect ratios, small Young's modulus and fracture toughness ratios between the hard and soft phases. Besides, the maximum fracture toughness is more likely to be obtained at a small aspect ratio and large Young's modulus ratio between hard and soft phases. The insights gained from our study would offer valuable guidance for the design and practical application of nacre-mimetic composites.

mechanics
Printing nature: Unraveling the role of nacre's mineral bridges

Grace X Gu,Flavia Libonati,Susan D Wettermark,Markus J Buehler

DOI: https://doi.org/10.1016/j.jmbbm.2017.05.007

Abstract:Creating materials with strength and toughness has been a long-sought goal. Conventional engineering materials often face a trade-off between strength and toughness, prompting researchers seeking to overcome these limitations to explore more sophisticated materials, such as composites. This paradigm shift in material design is spurred by nature, which exhibits a plethora of heterogeneous materials that offer outstanding material properties, and many natural materials are widely regarded as examples of high-performing hybrid materials. A classic example is nacre, also known as mother-of-pearl, which boasts a combination of high stiffness, strength, and fracture toughness. Various microstructural features contribute to the toughness of nacre, including mineral bridges (MBs), nano-asperities, and waviness of the constituent platelets. Recent research in biomimicry suggests that MBs contribute to the high strength and toughness observed in nacre and nacre-inspired materials. However, previous work in this area did not allow for complete control over the length scale of the bridges and had limitations on the volume fraction of mineral content. In this work, we present a systematic investigation elucidating the effects of structural parameters, such as volume fraction of mineral phase and density of MBs, on the mechanical response of nacre-inspired additive manufactured composites. Our results demonstrate that it is possible to tune the composite properties by tuning sizes and content of structural features (e.g. MBs and mineral content) in a heterogeneous material. Looking forward, this systematic approach enables materials-by-design of complex architectures to tackle demanding engineering challenges in the future.
Multifunctional Artificial Nacre Via Biomimetic Matrix-Directed Mineralization

Yu-Feng Meng,Bo Yang,Li-Bo Mao,Shu-Hong Yu

DOI: https://doi.org/10.52396/justc-2022-0022

2022-01-01

JUSTC

Abstract:Natural nacre, one of the most studied biological structural materials with delicate hierarchical structures and extraordinary performance, has inspired the design and fabrication of artificial structural ceramics with high fracture toughness. However, to meet the diverse requirements of different applications, future structural materials must be multifunctional with superior mechanical properties, such as strength, hardness, and toughness. Herein, based on the matrix-directed mineralization method for producing biomimetic structural materials, we introduce nanoparticles with different inherent functions into the platelets of artificial nacre via the co-mineralization of aragonite and the nanoparticles. Besides their enhanced mechanical properties, the obtained artificial nacre materials also exhibit different functions depending on the type of the nanoparticles. To extend the versatility of this strategy, the effects of nanoparticles of different sizes and zeta potentials on mineralization are also analyzed. This universal strategy can be applied to the fabrication of other types of functionalized biomimetic structural ceramics that have potential applications in various fields, such as biomedical science.
Superior Biomimetic Nacreous Bulk Nanocomposites by a Multiscale Soft-Rigid Dual-Network Interfacial Design Strategy

Si-Ming Chen,Huai-Ling Gao,Xiao-Hao Sun,Zhi-Yuan Ma,Tao Ma,Jun Xia,Yin-Bo Zhu,Ran Zhao,Hong-Bin Yao,Heng-An Wu,Shu-Hong Yu

DOI: https://doi.org/10.1016/j.matt.2019.03.012

IF: 18.9

2019-01-01

Matter

Abstract:Biomimetic bulk structural materials have been paid increasing attention for their huge application prospects. Integrating close-to-ideal, ultrathin, and flexible nanostructured units into high-performance nacreous bulk nanocomposites is worth considering yet remains challenging due to the elusive micro- and nano-interface connections. Here, by introducing amultiscale soft-rigid polymer dual-network interfacial design strategy that enables us to appropriately reinforce the nanoscale building blocks or their bridging, we can construct a type of nacreous bulk nanocomposites with tunable mechanical properties in the mild, eco-friendly, and highly efficient bottom-up assembly process. The resultant nanocomposites can achieve continuously reinforced mechanical transformation without experiencing environmentally threatening interfacial manipulation processes. This interfacial design strategy, supported by sufficient experiments and simulations, endows the assembled nacreous nanocomposite with superior mechanical enhancement and improved stability under high humidity and temperature conditions. Combined with the scalable assembly technique, it will pave the way for the design of high-performance biomimetic bulk nanocomposites for structural applications.
The weak interfaces within tough natural composites: experiments on three types of nacre

Ahmad Khayer Dastjerdi,Reza Rabiei,Francois Barthelat

DOI: https://doi.org/10.1016/j.jmbbm.2012.09.004

Abstract:Mineralization is a typical strategy used in natural materials to achieve high stiffness and hardness for structural functions such as skeletal support, protection or predation. High mineral content generally leads to brittleness, yet natural materials such as bone, mollusk shells or glass sponge achieve relatively high toughness considering the weakness of their constituents through intricate microstructures. In particular, nanometers thick organic interfaces organized in micro-architectures play a key role in providing toughness by various processes including crack deflection, crack bridging or energy dissipation. While these interfaces are critical in these materials, their composition, structure and mechanics is often poorly understood. In this work we focus on nacre, one of the most impressive hard biological materials in terms of toughness. We performed interfacial fracture tests on chevron notched nacre samples from three different species: red abalone, top shell and pearl oyster. We found that the intrinsic toughness of the interfaces is indeed found to be extremely low, in the order of the toughness of the mineral inclusions themselves. Such low toughness is required for the cracks to follow the interfaces, and to deflect and circumvent the mineral tablets. This result highlights the efficacy of toughening mechanisms in natural materials, turning low-toughness inclusions and interfaces into high-performance composites. We found that top shell nacre displayed the highest interfacial toughness, because of higher surface roughness and a more resilient organic material, and also through extrinsic toughening mechanisms including crack deflection, crack bridging and process zone. In the context of biomimetics, the main implication of this finding is that the interface in nacre-like composite does not need to be tough; the extensibility or ductility of the interfaces may be more important than their strength and toughness to produce toughness at the macroscale.
Mineral bridges in nacre revisited

Antonio G. Checa,Julyan H. E. Cartwright,Marc-Georg Willinger

DOI: https://doi.org/10.48550/arXiv.1207.5025

2012-07-21

Abstract:We confirm with high-resolution techniques the existence of mineral bridges between superposed nacre tablets. In the towered nacre of both gastropods and the cephalopod Nautilus there are large bridges aligned along the tower axes, corresponding to gaps (150-200 nm) in the interlamellar membranes. Gaps are produced by the interaction of the nascent tablets with a surface membrane that covers the nacre compartment. In the terraced nacre of bivalves bridges associated with elongated gaps in the interlamellar membrane (> 100 nm) have mainly been found at or close to the edges of superposed parental tablets. To explain this placement, we hypothesize that the interlamellar membrane breaks due to differences in osmotic pressure across it when the interlamellar space below becomes reduced at an advanced stage of calcification. In no cases are the minor connections between superimposed tablets (< 60 nm), earlier reported to be mineral bridges, found to be such.

Biological Physics,Materials Science,Soft Condensed Matter,Adaptation and Self-Organizing Systems,Other Quantitative Biology
Cracks Fail to Intensify Stress in Nacreous Composites

Haimin Yao,Zhigong Song,Zhiping Xu,Huajian Gao

DOI: https://doi.org/10.1016/j.compscitech.2013.03.016

IF: 9.1

2013-01-01

Composites Science and Technology

Abstract:Linear elastic fracture mechanics (LEFM) implies that crack-like flaws would intensify stress in brittle materials with stress intensity scaling up with the square root of the crack size. Therefore, the apparent strength of materials tends to be much smaller than the theoretical value. In this paper, we examine the stress state in nacreous composites and find that in such materials the crack-induced stress intensification and its dependence on crack size can be suppressed greatly. This feature of nacreous composites can be attributed to the unique “brick-and-mortar” (B-and-M) structure and a synergistic match of the mechanical properties between “brick” (e.g. minerals) and “mortar” (e.g. proteins) phases. Our findings not only provide a fundamental insight into the origin of the excellent mechanical properties of nacreous composites such as high strength, high toughness and flaw tolerance, but also will be of great value to the design and synthesis of new structural materials for superior mechanical properties.
Nacre's Brick–mortar Structure Suppresses the Adverse Effect of Microstructural Randomness

Yi Yan,Zi-Long Zhao,Xi-Qiao Feng,Huajian Gao

DOI: https://doi.org/10.1016/j.jmps.2021.104769

2022-01-01

Abstract:ABSTR A C T Biological materials have evolved various degrees of robustness against microscopic defects and structural randomness. Of particular interest here is whether and how nacre's brick-mortar structure suppresses the adverse effect of microstructural randomness. To this end, a tension--shear-chain (TSC) network model, combined with the virtual internal bond concept, is adopted to investigate the effects of microstructural randomness of nacre, where we show that the ensemble strength and failure behaviors of a larger TSC model exhibit substantially lower randomness. Our results indicate that the staggered brick-mortar structure renders nacre insensitive to micro-structural randomness, resulting in enhanced resistance to strain localization and crack initiation at weaker interfaces. The influence of microstructural randomness on the size effect of the ensemble mechanical properties of nacre is also revealed. This study provides further insights and guidelines for designing strong and robust nacre-mimic composites.

Optimal Characteristic Nanosizes of Mineral Bridges in Mollusk Nacre

Nanostructured individual nacre tablet: a subtle designed organic–inorganic composite

A Microstructural Study of Individual Nacre Tablet of Pinctada Maxima

Damage-Tolerance Strategies for Nacre Tablets

Arrangement of Intra-Crystalline Organic Matrix in Nacre from Red Abalone: A View by High-Resolution Synchrotron Powder Diffraction Combined with SEM Observation

Discontinuous crack-bridging model for fracture toughness analysis of nacre

On Flaw Tolerance of Nacre: a Theoretical Study.

Optimization Design of Strong and Tough Nacreous Nanocomposites Through Tuning Characteristic Lengths

Mineral Asperities Reinforce Nacre Through Interlocking and Friction-like Sliding

Analysis of Optimal Crosslink Density and Platelet Size Insensitivity in Graphene-Based Artificial Nacres.

Multi-parameter Structural Optimization to Reconcile Mechanical Conflicts in Nacre-Like Composites

Interfacial Strength-Controlled Energy Dissipation Mechanism and Optimization in Impact-Resistant Nacreous Structure

Maximum Utilization of Nacre-Mimetic Composites by Architecture Manipulation and Interface Modification Towards Critical Damage State

Fracture behaviors of nacre-like composites via phase-field fracture modeling

Printing nature: Unraveling the role of nacre's mineral bridges

Multifunctional Artificial Nacre Via Biomimetic Matrix-Directed Mineralization

Superior Biomimetic Nacreous Bulk Nanocomposites by a Multiscale Soft-Rigid Dual-Network Interfacial Design Strategy

The weak interfaces within tough natural composites: experiments on three types of nacre

Mineral bridges in nacre revisited

Cracks Fail to Intensify Stress in Nacreous Composites

Nacre's Brick–mortar Structure Suppresses the Adverse Effect of Microstructural Randomness