Abstract:One of the important failure criteria of press operations in industry for forming simulations is the Forming Limit Diagram (FLD). The complex loading effects on FLD, in particular the localized necking phenomenon under stretch-bending condition, have not been fully investigated and well understood. In practical sheet metal applications, the deformation is invariably three dimensional with a combination of stretching and bending. For most sheet materials under these complex loading processes used in industry, strong Bauschinger effect is observed, and the material hardening behavior tends to be anisotropic. This study aims to understand and evaluate such anisotropic hardening effect on the forming limit prediction under stretch-bending condition. The extended through-thickness Marciniak–Kuczynski (M–K) analysis is incorporated with Yoshida–Uemori (YU) two-surface kinematic hardening constitutive model, which has a more accurate description of the reverse loading behavior than that of the conventional isotropic hardening model. The material parameters used in this paper for YU model are calibrated with the experimental data from uniaxial large-strain tension-compression cyclic test. Both the isotropic hardening and YU kinematic hardening models with Hill'48 yield surface are employed in the analysis for the purpose of comparison. The Forming Limit Average Stress Diagram (FLASD) under stretch-bending condition is proposed to extend the understanding of Forming Limit Stress Diagram (FLSD) from in-plane to out-of-plane deformations. The “bending-ratio-dependent” phenomenon in forming limit diagram is predicted and observed in both stress/strain space with the proposed method. It suggests that the individual stress/strain state cannot represent system behavior. Forming limits under stretch-bending is suggested as an occurrence of system instability, not individual material instability. The system behavior of sheet metal deformation is reinforced as critical to the understanding of necking instability in stretch bending processes. The analysis shows that the Bauschinger effect provides positive effect in delaying the necking instability, predicting higher formability for sheet metals under stretch-bending. The insight obtained in this paper provides further understanding of the localized necking phenomenon under stretch-bending condition.

PREDICTION OF FORMING LIMIT DIAGRAMS OF DP590 STEEL BASED ON THE M-K MODEL WITH EXPERIMENTAL VERIFICATION

Forming Limit Calculation Based on the M-K Model with Yld96 Yield Function

Prediction on the Mechanical and Forming Behavior of DP590 Steel Based on a Flow Model

Prediction of fracture forming limit for DP780 steel sheet

Analytical Study of the Effect of Material Properties on the Formability of Sheet Metals Based on the M-K Model

Formability Prediction of Advanced High Strength Steel with A New Ductile Fracture Criterion

Prediction on the Mechanical and Forming Behaviors of Ferrite-Martensite Dual Phase Steels Based on a Flow Model

M–K Analysis of Forming Limit Diagram under Stretch-Bending

Forming Limits of a Sheet Metal after Continuous-Bending-Under-Tension Loading

Formability prediction of high‐strength steel sheet using experimental, analytical and theoretical analysis based on strain and stress forming limit curves and its application to automotive forming parts

New Robust Algorithms for Marciniak–Kuczynski Model to Calculate the Forming Limit Diagrams

Prediction of Forming Limits for Anisotropic Materials with Nonlinear Strain Paths by an Instability Approach

Sheet metal forming limits under stretch-bending with anisotropic hardening

Effect of nonlinear strain paths on forming limits under isotropic and anisotropic hardening

M–K model based forming limit prediction of aluminum–lithium alloy 2060 and its application in hot stamping

Forming Limits under Stretch-Bending Through Distortionless and Distortional Anisotropic Hardening

Comparison of Two Uncoupled Ductile Damage Initiation Models Applied to DP900 Steel Sheet under Various Loading Paths

A Rate-Dependent Model for Metals Based on a Master Curve of Normalized Hardening Behavior of DP Steels

Experimental Investigation on Forming Limit Predicting Model for TRIP High Strength Sheet Steels

Feasibility evaluation of failure models for predicting forming limit of metal foils

An improved Marciniak-Kuczynski approach for predicting sheet metal formability