Anion Exchange Membranes by Bromination of Benzylmethyl-Containing Poly(Arylene Ether)S for Alkaline Membrane Fuel Cells

Xiuhua Li,Shanshan Cheng,Liuchan Wang,Qiang Long,Jinxiong Tao,Guanghui Nie,Shijun Liao

DOI: https://doi.org/10.1039/c4ra00833b

IF: 4.036

2014-01-01

RSC Advances

Abstract:Fast and safe fabrication of anion exchange membranes started with the bromination of poly(arylene ether)s containing tetramethyl triphenyl methane moieties.

What problem does this paper attempt to address?

Poly(olefin)-Based Anion Exchange Membranes Prepared Using Ziegler–Natta Polymerization

Liang Zhu,Xuedi Yu,Xiong Peng,Tawanda J. Zimudzi,Nayan Saikia,Michael T. Kwasny,Shaofei Song,Douglas I. Kushner,Zhisheng Fu,Gregory N. Tew,William E. Mustain,Michael A. Yandrasits,Michael A. Hickner

DOI: https://doi.org/10.1021/acs.macromol.8b02756

IF: 5.5

2019-01-01

Macromolecules

Abstract:Bromoalkyl-functionalized poly(olefin)s were synthesized by copolymerization of 4-(4-methylphenyl)-1-butene with 11-bromo-1-undecene using Ziegler-Natta polymerization. The resulting bromoalkyl-functionalized poly(olefin)s were converted to quaternary ammonium-containing anion-conductive copolymers by reacting the pendant bromoalkyl group with trimethylamine or a custom-synthesized tertiary amine containing pendant quaternary ammonium moieties. Poly(olefin)-based AEMs with three cations per side chain showed considerably higher hydroxide conductivities, up to 201 mS/cm at 80 degrees C in liquid water, compared to that of samples with only one cation per bromoalkyl site (68 mS/cm, 80 degrees C, liquid water), likely due to phase separation in the triple-cation structure. More importantly, triple-cation side-chain poly(olefin) AEMs exhibited higher hydroxide conductivity under relative humidity conditions (50%-100%) than typical AEMs based on benzyltrimethylammonium cations. The triple-cation the triple-cation side-chain poly(olefin)-based AEM exhibited an ionic conductivity as high as 115 mS/cm under 95% RH at 80 degrees C and 11 mS/cm under 50% RH at 80 degrees C. In addition to high ionic conductivity, the triple-cation side-chain poly(olefin) AEMs exhibited good chemical and dimensional stability. High retention of ionic conductivity (>85%) was observed for the samples in 1 M NaOH at 80 degrees C over 1000 h. Based on these high-performance poly(olefin) AEMs, a fuel cell with a peak power density of 0.94 W cm(-2) (1.28 W cm(-2) after iR correction) was achieved under H-2/O-2 at 70 degrees C. The results of this study suggest a new, low-cost, and scalable route for preparation of poly(olefin)-based AEMs for anion exchange membrane applications.
Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

Jun Liang,Jiao Ge,Kai Wu,Qi Zhang,Jianli Wang,Zhibin Ye

DOI: https://doi.org/10.1016/j.memsci.2019.117626

IF: 9.5

2019-01-01

Journal of Membrane Science

Abstract:We synthesized a range of sulfonated polyaryletherketone (x%SCBI-SPAEK-6F) with pendant benzimidazole side groups at a tunable molar percentage (x within 5-15%) for potential application as proton exchange membrane (PEM). A systematic study had been undertaken to study the performance and the underlying structure-properties relationship of PEMs fabricated by those novel amphoteric polymers. It was found that the dimensional stability, oxidative stability and methanol resistance performance of x%SCBI-SPAEK-6F membranes were significantly improved with the increase of the benzimidazole content due to the acid-base interaction. In particular, the 5%SCBI-SPAEK-6F membrane exhibited a relative selectivity (10.5 x 10(3) S s cm(-3)) almost 20 times higher than that of Nafion117 membrane at 75 degrees C, demonstrating the significant promoted proton conductivity (0.35 S cm(-1)) and reduced methanol penetration (6 x 10(-7) cm(2) s(-1)) by the ionic barrier. With such superior performance, these polymers are promising for the fabrication of practical proton exchange membranes in commercial fuel cells.
Novel Cross-Linked Anion Exchange Membranes with Diamines As Ionic Exchange Functional Groups and Crosslinking Groups

Shiman Zhang,Cunpu Li,Xiaofeng Xie,Fushi Zhang

DOI: https://doi.org/10.1016/j.ijhydene.2014.03.122

IF: 7.2

2014-01-01

International Journal of Hydrogen Energy

Abstract:Two novel cross-linked anion exchange membranes (AEMs) for alkaline fuel cells (AFCs) were synthesized via nucleophilic substitution reactions. Brominated poly(2,5-bis(perfluorophenyl)-1,3,4-oxadiazole-co-allyl bisphenol), called as precursory polymer (PP), was synthesized by reaction of 2,5-bis(2,3,4,5,6-pentafluorophenyl)-1,3,4-oxadiazole (FPOx) and diallyl bisphenol A (DABPA) followed by bromination. Ethanediamine (EDA) and propane diamine (PDA) were introduced to PP to obtain cross-linked polymers EDA-PP and PDA-PP, respectively. The reactions between PP and diamines rolled the crosslinking and functionalizing process in one. The crosslinking process enhanced the thermal and mechanical stabilities of EDA-PP and PDA-PP, which were affected by the length of alkyl chains of diamines. Meanwhile, the conjugated system of PP extended the electron clouds around the amine groups, which improved the thermal stability and alkaline durability of quaternary ammonium (QA) groups. The solution casting membranes of EDA-PP and PDA-PP showed high ionic conductivities. The swelling ratios, TGA and AFM properties of the membranes also demonstrated their good mechanical and thermal stabilities.
Environmentally friendly synthesis of alkaline anion exchange membrane for fuel cells via a solvent-free strategy

Liang Wu,Guangfeng Zhou,Xingqin Liu,Zheng Zhang,Chuanrun Li,Tongwen Xu

DOI: https://doi.org/10.1016/j.memsci.2011.01.036

IF: 9.5

2011-01-01

Journal of Membrane Science

Abstract:In this study, we described a solvent-free strategy for alkaline anion exchange membranes synthesis by in situ polymerization. Different from the available membrane synthesis by direct polymerization and post-polymerization modification, the non-solvent strategy demonstrated here was performed by dissolving brominated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO) in monomers mixture of vinylbenzyl chloride (VBC) and divinylbenzene (DVB) and then in situ polymerization to incorporate BPPO into the network of poly(VBC-DVB). After quaternization, a translucent, flexible and robust anion exchange membrane was obtained. The membrane morphology was confirmed by SEM-EDXA images. Factors such as quaternizing conditions and components of the casting solution were fully investigated. The optimized membranes exhibited favorable water uptakes (ranging from 19.9% to 29.3%) and hydrated hydroxyl conductivities (ranging from 0.017 to 0.028Scm-1) at room temperature, which allows its application in alkaline anion exchange membrane fuel cells (AAEMFCs). Moreover, this solvent-free strategy is not limited to the above BPPO/VBC/DVB system. It can be applied to other compatible systems of (aromatic) polymers and (aromatic) monomers as long as homogeneous cast solution of the monomers and polymers can be formed. Thus this research will provide a versatile environmentally friendly route to prepare anion exchange membranes with tailored properties for alkaline fuel cells. © 2011 Elsevier B.V.
Branched Anion-Conducting Poly(arylene Alkylene)s for Alkaline Membrane Fuel Cells

Lijuan Li,Tao Jiang,Sheng Wang,Sheng Cheng,Xueliang Li,Haibing Wei,Yunsheng Ding

DOI: https://doi.org/10.1021/acsaem.1c03952

IF: 6.4

2022-01-01

ACS Applied Energy Materials

Abstract:Branched, bromopentyl-tethered poly(arylene alkylene)s were synthesized by Friedel-Crafts polyhydroxyalkylation of 7-bromo-1,1,1-trifluoroheptan-2-one and biphenyl with the addition of a small amount of trifunctional monomer (0.5-2.0 mol %), 1,3,5-triphenylbenzene. The subsequent conversion of bromomethyl group of bromopentyl-tethered precursors to quaternary ammonium (QA) to afford cationic ionomers, and these ionomers were then solution-cast into anion-conductive membranes. Compared to the linear, unbranched poly(arylene alkylene)-based AEM analogue, branched membranes exhibited suppressed water absorption, a low hydration number, and good swelling resistance, likely due to the improved chain entanglements as a result of branching. More importantly, although with an 11-38 wt % reduction in water absorption, the branched membranes showed comparable conductivities to the unbranched counterpart, which can be interpreted by the fact that the well-reserved phase-separated morphology and improved ion concentration took place after polymer branching. Specifically, at 80 degrees C, the conductivities of 131 and 63 mS cm(-1) were recorded for branched membrane BPBPA-1.0% DB in the OH- and Cl- forms, respectively. In addition to the suppressed water uptake and high ion conductivity, the branched membranes exhibited excellent alkaline durability. Over 97% conductivity retention and no structural degradation were observed for B-PBPA-1.0% DB after a 1000-h aging in 1 M NaOH at 80 degrees C. H-2-O-2 fuel cell performance was evaluated with the branched membrane B-PBPA-1.0% DB, and a peak power density of 690 mW cm(-2) was achieved at 80 degrees C. The results of this study provide a new polymer structural modification for the fabrication of advanced ionomeric materials for electrochemical technology applications.
Branched, Side-Chain Grafted Polyarylpiperidine Anion Exchange Membranes for Fuel Cell Application

Lei Bai,Lingling Ma,Lv Li,Anran Zhang,Xiaoming Yan,Fengxiang Zhang,Gaohong He

DOI: https://doi.org/10.1021/acsaem.1c01037

IF: 6.4

2021-01-01

ACS Applied Energy Materials

Abstract:Anion exchange membrane (AEM) is the heart of alkali electrolyte membrane fuel cells (AEMFCs). To achieve high performance of AEMFC, high conductivity and alkaline stability of AEMs are highly desired. In the present work, we report the synthesis of ether-free polymers with different degrees of Y-shaped branching as AEM materials. Our investigations reveal that incorporating bulky, rigid, and Y-branching units into the polymer backbone can increase the free volume of the AEM and thus help build ion channels with lower hydroxide ion transport resistance. The resultant AEM showed a markedly improved ionic conductivity (116.92 mS/cm at 80 degrees C), while the simple linear type of the AEM only showed an ion conductivity of 63.63 mS/cm at a similar ion exchange capacity. With such an AEM, the peak power density of the H-2/O-2 single cell at 60 degrees C reaches 275 mW/cm(2).
Hyper-Branched Anion Exchange Membranes with High Conductivity and Chemical Stability

Qianqian Ge,Yazhi Liu,Zhengjin Yang,Bin Wu,Min Hu,Xiaohe Liu,Jianqiu Hou,Tongwen Xu

DOI: https://doi.org/10.1039/c6cc04930c

IF: 4.9

2016-01-01

Chemical Communications

Abstract:In the manuscript, we report the design and preparation of hyper-branched polymer electrolytes intended for alkaline anion exchange membrane fuel cells. The resulting membrane exhibits high conductivity, lower water swelling and shows prolonged chemical stability under alkaline conditions.
Novel poly(biphenyl-alkylene) anion exchange membranes with excellent flexibility for fuel cells

Xi Bin Yue,Xi Hao Wang,Hui Peng,Li Wei Lai,Qiu Gen Zhang,Ai Mei Zhu,Qing Lin Liu

DOI: https://doi.org/10.1016/j.memsci.2024.122531

IF: 9.5

2024-02-05

Journal of Membrane Science

Abstract:As the core material of alkaline fuel cells, anion exchange membranes (AEMs) are one of the keys to determining the comprehensive performance of fuel cells. However, drawbacks, such as impoverished alkali stability, insufficient mechanical properties, and particularly low ionic conductivity, affect their application in fuel cells. Herein, a series of AEMs based on a new arylfluoroketone monomer [1-bromo-3- (trifluoroacetyl phenyl)-propane, TFAP-Br] was prepared using a backbone modification strategy. This study aims to investigate the effects of introducing TFAP-Br for copolymerization on the microphase separation, ionic conductivity, and mechanical properties of AEMs. Due to the presence of long side chains of alkylfluoroketone and arylfluoroketone, the AEMs exhibit a prominent microphase separation state, and the OH − conductivity can reach 156 mS cm −1 at 80 °C (IEC = 2.73 meq g −1 ). QBPNP-10 shows excellent mechanical properties with the elongation at break up to 91% in wet state and good alkali resistance with 95.2% OH − conductivity retention in a NaOH solution (2 mol L −1 , 80 °C, 1560 h). Moreover, the peak power density (PPD) of a single cell assembled with QBPNP-10 can reach 852 mW cm −2 (80 °C), and the membrane has good in-situ durability.

engineering, chemical,polymer science
Novel Alkaline Anion Exchange Membranes Containing Pendant Benzimidazolium Groups for Alkaline Fuel Cells

Xiaocheng Lin,Xuhao Liang,Simon D. Poynton,John R. Varcoe,Ai Lien Ong,Jin Ran,Yan Li,Qiuhua Li,Tongwen Xu

DOI: https://doi.org/10.1016/j.memsci.2013.04.059

IF: 9.5

2013-01-01

Journal of Membrane Science

Abstract:Novel benzimidazolium (BIm) functionalized anion exchange membranes (AEMs) are synthesized and characterized for alkaline fuel cells (AFCs). Poly(phenylene oxide) (PPO) is firstly brominated followed by nucleophilic substitution reaction with methylbenzimidazole to obtain the objective BIm-PPO AEMs. Such solution-casting AEMs show good mechanical and thermal stabilities as well as the favorable fuel cell-related indicators, including high ion exchange capacity, proper water uptake and high ionic conductivity. In addition, a single H2/O2 fuel cell test by employing the optimal BIm-PPO-0.54 AEM yields a peak power density of 13mWcm−2 at 35°C, indicating the potential application of BIm-PPO AEMs in AFCs. Compared with the analogous AEMs based on PPO containing the classical pendant quaternary ammonium and imidazolium cations, BIm-PPO AEMs show the advantages in dimensional, mechanical and thermal stabilities, while simultaneously exhibiting the higher ionic conductivity. Compared with polybenzimidazolium based AEMs, where BIm cations distribute within the polymer backbone, AEMs herein present the higher ionic conductivity and power density (produced from a single cell test) due to the better mobility and aggregation abilities of pendant BIm cations attached to the backbone via a side chain relative to those distribute within the polymer backbone.
Towards high alkaline stability and fuel cell performance in anion exchange membranes via backbone−cation alkylene spacer tuning for quaternized poly(biphenylene alkylene)s

Tao Wang,Yu Zhao,Sheng Wang,Sheng Cheng,Shanzhong Yang,Haibing Wei,Yunsheng Ding

DOI: https://doi.org/10.1016/j.jpowsour.2022.232590

IF: 9.2

2023-01-01

Journal of Power Sources

Abstract:A major challenge in anion exchange membrane (AEM) fuel cells is the development of high-performed AEMs that can simultaneously meet the criteria of alkaline stable, swelling resistant, and ion conductive. Pentyltrimethylammonium-tethered poly(arylene alkylene)s are emerging as one of the most promising candidates in AEM community, however, they also suffer from conductivity−water uptake trade-offs and improvement-needed alkaline stability. Herein, a series of poly(biphenylene alkylene)-based membranes, PBPA- n -QAs ( n = 4, 5, 6), with different alkylene spacer length are synthesized by hydroxyalkylation polymerization and the subsequent amination. The membranes are found to have an improved phase separation as the number of carbon atoms of the alkylene spacers increased from 4 to 6. The ordered morphology and continuous hydrophilic channels make the PBPA-6-QA membrane with outstanding properties including suppressed water uptake, high ion conductivity, and improved alkaline stability. Specifically, the PBPA-6-QA membrane yields the highest hydroxide conductivity (180 mS cm −1 at 80 °C), which is considerably higher than that of PBPA-5-QA and PBPA-4-QA. Furthermore, a single cell using PBPA-6-QA shows a peak power density of 0.97 W cm −2 and can operates stably at a constant current density of 0.2 A cm −2 for 90 h without membrane degradation.

energy & fuels,materials science, multidisciplinary,electrochemistry,chemistry, physical
Naphthalene-based Poly(arylene Ether Ketone) Anion Exchange Membranes

Zhuang Liu,Xiaobai Li,Kunzhi Shen,Pengju Feng,Yinan Zhang,Xu,Wei Hu,Zhenhua Jiang,Baijun Liu,Michael D. Guiver

DOI: https://doi.org/10.1039/c3ta10355b

IF: 11.9

2013-01-01

Journal of Materials Chemistry A

Abstract:Naphthalene-based poly(arylene ether ketone)s were obtained through a three-step process involving polymerization of methylated polymers, followed by bromination and derivatization with a diquaternary-ammonium group. The ionic conductivities of the anion exchange membranes were above 10−2 S cm−1 at room temperature and the membrane with an IEC = 1.46 mequiv. g−1 attained an ion conductivity of 7.4 × 10−2 S cm−1 at 100 °C, which is higher than many reported results. The membrane series had low water uptake and excellent dimensional stability, even at the highest IEC values. In addition, the membranes were insoluble in organic solvents and concentrated alkaline solutions for many days, even under heating, suggesting their excellent stability. These combined data suggest that the membranes have potential to be used as anion exchange membranes for fuel cells applications.
Two new anion exchange membranes based on poly(bis-arylimidazolium) ionenes blend polybenzimidazole

Na Yu,Jianhao Dong,Tingting Wang,Yaping Jin,Weiqin Tang,Jingshuai Yang

DOI: https://doi.org/10.1016/j.polymer.2021.124491

IF: 4.6

2022-02-01

Polymer

Abstract:The development of polymer membranes with excellent alkaline stability and high hydroxide conductivity is a huge challenge to fuel cells. Herein, two blend membranes based on poly(bis-arylimidazolium)s (i.e. Ppbim and Ptpim) and polybenzimidazole (PBI) are prepared and used as anion exchange membranes. Ppbim and Ptpim ionenes are synthesized from bis-imidazole compounds (i.e. pbim and tpim) and α,α′-dibromo-p-xylene via the Menshutkin reaction, while pbim and tpim are synthesized from 2-phenylbenzimidazole (or 2,4,5-triphenylimidazole) with 1,4-dibromobutane through the nucleophilic substitution reaction. The physicochemical properties such as water uptake, ion exchange capacity, swelling, tensile strength and conductivity can be adjusted by changing the molar ratio of pbim (or tpim) to PBI in the blend membranes. Comparing with Ppbim, Ptpim containing bulky tri-phenyl groups exhibits better alkaline stability due to the steric hindrance effect of tri-phenyl groups. The technical feasibility of the Ptpim-51%PBI membrane for the anion exchange membrane fuel cell is demonstrated by the polarization curves. This work provides a straightforward method to synthesize water-insoluble ether-free polymers with dicationic groups in the polymer repeat unit.

polymer science
Conductivity-enhanced Poly(biphenyl piperidine) anion exchange membranes with organic tubes

Dingting Yang,Xiuyang Zou,Meisheng Li,Yan Zhang,Shouyong Zhou,Dawei Yang,Yijiang Zhao

DOI: https://doi.org/10.1016/j.memsci.2024.123414

IF: 9.5

2024-10-22

Journal of Membrane Science

Abstract:Anion exchange membrane fuel cells (AEMFCs) present an economically efficient alternative to proton exchange membrane fuel cells because of the use of non-precious metals. The development of high-performance and durable AEMFCs necessitates the use of highly conductive and robust anion exchange membranes (AEMs). In this study, a novel organic-organic composite AEM was synthesized by preparing poly(arylene piperidinium) polymer through Friedel-Crafts acid condensation and incorporating one-dimensional organic tubes as reinforcing materials. The composite AEM exhibits high conductivity (235 mS cm −1 at 80 °C) due to the chain orientation within the organic tubes and the availability of abundant transport sites. Furthermore, in contrast to the incompatibility of inorganic materials with polymers, the flexible nature of organic tubes enhanced polymer entanglement, significantly boosting the mechanical strength (120 MPa) of the AEM. Crosslinking the polymer backbone with the organic tubes facilitated simultaneous swelling, effectively mitigating interfacial compatibility issues, result in high dimensional stability. The H 2 –O 2 fuel cell employing the developed AEM demonstrated a peak power density of 1018 mW cm −2 at 80 °C. This study provides a comprehensive synthetic strategy for producing stable AEMs with high hydroxide ion conductivity and outstanding mechanical properties tailored for alkaline membrane fuel cell applications.

engineering, chemical,polymer science
Anion exchange membranes with branched ionic clusters for fuel cells

Yubin He,Xiaolin Ge,Xian Liang,Jianjun Zhang,Muhammad A. Shehzad,Yuan Zhu,Zhengjin Yang,Liang Wu,Tongwen Xu

DOI: https://doi.org/10.1039/c8ta01114a

IF: 11.9

2018-01-01

Journal of Materials Chemistry A

Abstract:Highly conductive anion exchange membranes (AEMs) are urgently desired for various electro-chemical technologies like fuel cells, flow batteries and electro-dialysis. Available strategies for enhancing the hydroxide conductivity of AEMs commonly focus on increasing the concentration of cationic sites, which, in turn, causes undesirable, excessive dimensional swelling and poor alkaline stability. To overcome this problem, a novel AEM with flexible branched ionic clusters was developed in this study. The improved cation density and cation mobility in the branched ionic clusters have resulted in highly ordered nano-scale channels for hydroxide ion transport and an excellent fuel cell performance of 266 mW cm(-2) at 60 degrees C. Low water uptake and restricted swelling ratio as well as good alkaline stability were also observed benifiting from its unique polymer architecture.
Cross-linked anion exchange membranes for alkaline fuel cells synthesized using a solvent free strategy

Xiaocheng Lin,Yanbo Liu,Simon D. Poynton,Ailien Ong,John R. Varcoe,Liang Wu,Yan Li,Xuhao Liang,Qiuhua Li,Tongwen Xu

DOI: https://doi.org/10.1016/j.jpowsour.2013.01.059

IF: 9.2

2013-01-01

Journal of Power Sources

Abstract:This article describes the preparation of cross-linked anion exchange membranes (AEMs) using a solvent free strategy. A novel casting solution is formed by dissolving cardo polyetherketone (PEK-C) as an essential polymer intensifier in a mixture of vinylbenzyl chloride (VBC) and divinylbenzene (DVB) monomers without any organic solvent. Tetraethylenepentamine (TEPA) is added to act as a cross-linker between VBC and PKE-C. Polymerization and quaternization are successively implemented to obtain the cross-linked AEMs, whose properties are found to compare well to many referenced AEMs. Apart from improving the compatibility of PEK-C with poly(VBC-co-DVB), TEPA also effectively enhances the charge density, ionic conductivity and alkaline stabilities of the resulting AEMs, whilst simultaneously inhibiting the swelling ratio. The optimal membrane shows an ionic conductivity of 76 mS cm−1 at 70 °C and 100% relative humidity and can remain stable after immersing in 2 mol dm−3 KOH solution for 168 h. A power density of 6 mW cm−2 is achieved in a H2/O2 fuel cell test at 50 °C with an optimal AEM but a non-optimized membrane electrode fabrication process. Generally, the novel method herein highlights an environmentally friendly and economically attractive method for the preparation of AEMs used in alkaline fuel cells.
A novel anion exchange membrane of three aromatic units copolymer for fuel cells

Shanchang Zheng,Yue Huang,Yani Hua,Zhan Gao

DOI: https://doi.org/10.1177/09540083241230034

IF: 1.73

2024-01-31

High Performance Polymers

Abstract:High Performance Polymers, Ahead of Print. Anion exchange membrane fuel cell (AEMFC) has made great progress recently due to the continuous improvement of anion exchange membrane (AEM). Aryl ether bond-free membranes are considered to be promising for improving the overall performance of AEMs. Here, we present a copolymer consisting of m-terphenyl, diphenyl ethane and biphenyl (PMDBP) to further enhance the microphase separation structure by introducing a third structural unit, biphenyl. Meanwhile, the more compact biphenyl structure enhances the mechanical strength of AEMs. Specifically, PMDBP AEMs possess superior OH- conductivity (up to 113 mS cm−1) and excellent mechanical properties (tensile strength up to 42 MPa). Furthermore, the PMDBP has an outstanding single-cell performance with a peak power density (PPD) of up to 95 mW cm−2 with a platinum-carbon (Pt/C) catalyst at 80°C in H2-air. In addition, PMDBP is provided with excellent durability, including NMR spectral consistency and over 90% ion conductivity retention in 1 M NaOH at 60°C for 720 h. This study provided a copolymer structure suitable for anion exchange membrane that can provide excellent performance for fuel cells and electrolyzers.

polymer science
Highly Anion Conductive, Alkyl-Chain-Grafted Copolymers As Anion Exchange Membranes for Operable Alkaline H-2/O-2 Fuel Cells

Cheng Yang,Lei Liu,Xiaojin Han,Zhanggen Huang,Junping Dong,Nanwen Li

DOI: https://doi.org/10.1039/c7ta00481h

IF: 11.9

2017-01-01

Journal of Materials Chemistry A

Abstract:Alkyl chain grafted AEMs have been demonstrated to be highly alkaline stable, anion conductive and fuel cell operable.
Synthesis and Characterization of Anion Exchange Membranes for Alkaline Direct Methanol Fuel Cells

Guoshun Liu,Yuming Shang,Xiaofeng Xie,Shubo Wang,Jinhai Wang,Yaowu Wang,Zongqiang Mao

DOI: https://doi.org/10.1016/j.ijhydene.2011.04.047

IF: 7.2

2012-01-01

International Journal of Hydrogen Energy

Abstract:Alkaline fuel cells suggest solution for the problems of low methanol oxidation kinetics and methanol crossover, which are limiting the development of direct methanol fuel cells. In this work, a novel anion exchange membrane, quaternized poly(aryl ether oxadiazole), was prepared through polycondensation, grafting and quaternization. The ionic conductivity of as-synthesized anion exchange membrane can reach up to 2.79 x 10(-2) S/cm at 70 degrees C. The physical and chemical stability of the anion exchange membranes could also meet the requirement for alkaline direct methanol fuel cells. Copyright (C) 2011, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.
New cancer therapeutics: target-specific in, cytotoxics out?

H. Broxterman,N. Georgopapadakou

DOI: https://doi.org/10.1016/J.DRUP.2004.02.004

IF: 22.841

2004-04-01

Drug Resistance Updates

Abstract:
Preparation and properties of PPO-based anion exchange membranes with flexible side chains for fuel cells

Yuan Jin,Dan Zhao,Jiaqi Wang,Yifan Li,Meisheng Li,Xiuyang Zou,Shouyong Zhou,Yijiang Zhao,Qi Zhang,Dawei Yang

DOI: https://doi.org/10.1016/j.reactfunctpolym.2024.105862

IF: 4.966

2024-04-01

Reactive and Functional Polymers

Abstract:Poor alkali resistance and low ionic conductivity are the crux of the matter that hinder the commercialization applications of anion exchange membranes (AEMs). Here, we designed and synthesized a range of poly(phenylene oxide) (PPO)-based AEMs with benzyl free side-chain type. After that, the influences of different cationic functional groups, such as quaternary ammonium, imidazole and piperidine, on the membrane performances were examined systemically. The introduction of ether bond-containing side chains to build micro-phase separation structures enhanced the conductivity of AEMs (64 mS·cm−1 at 80 °C). At the same time, the side-chain without benzyl structures effectively avoids the influence of electron withdrawing groups on PPO main chains. Moreover, the steric hindrance effect of the benzene ring can further alleviate the attack of OH−, thereby improving the alkali resistance of the membrane. Molecular dynamics simulations revealed that a well-developed hydrogen bonding network was formed between ether linkages and water molecules in the side-chain structures, which enhanced the electrical conductivity of the membrane. Meanwhile, the prepared membranes owned a good water uptake and a certain dimensional stability. These results provide a basis for the subsequent enhancement of membrane performances.

engineering, chemical,chemistry, applied,polymer science

Anion Exchange Membranes by Bromination of Benzylmethyl-Containing Poly(Arylene Ether)S for Alkaline Membrane Fuel Cells

Poly(olefin)-Based Anion Exchange Membranes Prepared Using Ziegler–Natta Polymerization

Sulfonated Polyaryletherketone with Pendant Benzimidazole Groups for Proton Exchange Membranes

Novel Cross-Linked Anion Exchange Membranes with Diamines As Ionic Exchange Functional Groups and Crosslinking Groups

Environmentally friendly synthesis of alkaline anion exchange membrane for fuel cells via a solvent-free strategy

Branched Anion-Conducting Poly(arylene Alkylene)s for Alkaline Membrane Fuel Cells

Branched, Side-Chain Grafted Polyarylpiperidine Anion Exchange Membranes for Fuel Cell Application

Hyper-Branched Anion Exchange Membranes with High Conductivity and Chemical Stability

Novel poly(biphenyl-alkylene) anion exchange membranes with excellent flexibility for fuel cells

Novel Alkaline Anion Exchange Membranes Containing Pendant Benzimidazolium Groups for Alkaline Fuel Cells

Towards high alkaline stability and fuel cell performance in anion exchange membranes via backbone−cation alkylene spacer tuning for quaternized poly(biphenylene alkylene)s

Naphthalene-based Poly(arylene Ether Ketone) Anion Exchange Membranes

Two new anion exchange membranes based on poly(bis-arylimidazolium) ionenes blend polybenzimidazole

Conductivity-enhanced Poly(biphenyl piperidine) anion exchange membranes with organic tubes

Anion exchange membranes with branched ionic clusters for fuel cells

Cross-linked anion exchange membranes for alkaline fuel cells synthesized using a solvent free strategy

A novel anion exchange membrane of three aromatic units copolymer for fuel cells

Highly Anion Conductive, Alkyl-Chain-Grafted Copolymers As Anion Exchange Membranes for Operable Alkaline H-2/O-2 Fuel Cells

Synthesis and Characterization of Anion Exchange Membranes for Alkaline Direct Methanol Fuel Cells

New cancer therapeutics: target-specific in, cytotoxics out?

Preparation and properties of PPO-based anion exchange membranes with flexible side chains for fuel cells