Abstract:Printed electronics are circuits that are additively manufactured using conductive pastes composed of micro-/nanoconductive metal particles. Silver-based compounds are the most widely used metals for such pastes due to their superior conductivity and oxidation stability. However, the high cost of silver (Ag) has demanded its replacement with more cost-effective and abundant metals such as copper (Cu). Despite its cost-effectiveness and abundance, Cu suffers from high oxidation tendency and sintering temperature that have limited its widespread utilization in printed electronics. In this work, we have developed a low-cost hybrid bimodal paste composed of Cu microparticles (1–5 μm) and Ag nanoparticles (20–30 nm) (CuMPs/AgNPs) via nondestructive photonic sintering. The concurrent melting of AgNPs and catalytic reduction of CuMPs allow the paste to be sintered at considerably low temperatures using an intense-pulsed light (IPL) source. The required light energy density for effective sintering of different mixing ratios of AgNPs and CuMPs was systematically measured using electrical, optical, and mechanical characterization techniques. These analyses revealed that a minimum of 16 wt % AgNPs in the bimodal CuMP/AgNP paste with an IPL irradiation energy of 10.6 J/cm2 and pulse duration of 5 ms achieved a minimum sheet resistance of 0.072 Ω/□ that results from localized melting of AgNPs between adjacent CuMPs. Furthermore, the CuMP/AgNP films with a minimum of 6 wt % AgNPs showed significantly improved oxidation stability characteristics even after 7 days of incubation in accelerated oxidation conditions [70 °C and 100% relative humidity (RH)]. As a proof of concept, we demonstrated an application of the developed paste (CuMPs-6 wt % AgNPs) by directly printing a wireless resonant moisture sensor onto the interior region of a cardboard package box, which is capable of performing in situ monitoring of the moisture ranging from 30 to 85% RH with an average linear sensitivity of −3.08 % RH/MHz.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaelm.1c00345.Thermal behavior of PVP, effect of drying temperature and duration on sheet resistance of the oven-dried CuMPs-6 wt % AgNP printed trace, followed by photonic sintering with optimum setting of two pulses at 10.6 J/cm2 energy, effect of EG on sheet resistance of the paste with CuMPs-6 wt % AgNP and CuMPs-16 wt % AgNP compositions, reoxidation, and damage assessment of the hybrid bimodal paste after photonic sintering with excessive thermal energy, effect of increasing thermal energy on sheet resistance of CuMPs-0 wt % AgNP printed trace EDX spectrum and elemental composition analysis (at %) of the photonically sintered CuMPs-16 wt % AgNP printed trace with optimum settings, and 3D confocal microscopy analysis of CuMPs-20 wt % AgNP printed trace (PDF)This article has not yet been cited by other publications.

Printed Cathode from Conducting Ag-Paste for Realization of All-Printable Polymer Light-Emitting Diodes

Stepwise Aggregation Control of PEDOT:PSS Enabled High-Conductivity, High-Resolution Printing of Polymer Electrodes for Transparent Organic Phototransistors

Full-Color Polymer Light Emitting Displays: Novel Emitting Polymers And Device Fabrication

Large‐Area Printed Display Based on Green Solvent Processable Blue Light‐Emitting Conjugated Polymer

Electropolymerized Thiophene-Based Polymer with Pure Donor System Enable Magenta-to-transmissive Electrochromic-Supercapacitor Bifunctional Material

All‐Printed Electrically Driven Lighting via Electrochemiluminescence (Adv. Mater. Technol. 16/2024)

Highly conductive polymer electrodes for polymer light-emitting diodes

Stable Junction Polymer Light-Emitting Electrochemical Cells

Realizing Diketopyrrolopyrrole Polymer‐Based Uniform Large‐Area Transistors for Active Circuit via Protonic Acid Mediated Molecular Self‐Assembly

Efficient Flexible Fabric‐Based Top‐Emitting Polymer Light‐Emitting Devices for Wearable Electronics

Synthesis of an electroluminescent polymer and its non-doped light-emitting diodes with stable green emission

Photoreactive and Metal-Platable Copolymer Inks for High-Throughput, Room-Temperature Printing of Flexible Metal Electrodes for Thin-Film Electronics.

Controlling the efficient and ultralong room-temperature phosphorescence of 9H-dibenzo[a,c]carbazole derivatives for erasable light printing

Synthesis of a new polymeric host material for efficient organic electro-phosphorescent devices.

Flexible ITO-free sky-blue polymer light-emitting diodes and printed polymer solar cells based on AgNW/PI transparent conductive electrode

Efficient Conjugated-Polymer Optoelectronic Devices Fabricated by Thin-Film Transfer-Printing Technique

Highly Conductive Copper–Silver Bimodal Paste for Low-Cost Printed Electronics

Optical Printing of Conductive Silver on Ultrasmooth Nanocellulose Paper for Flexible Electronics

Polymer light-emitting electrochemical cell based on a novel poly(aryleneethynylene) consisting of ethynylfluorene and tetraphenyldiaminobiphenyl units

Dual-Function Optoelectronic Polymer Device for Photoelectric Conversion and Electroluminescence

Effect of Polymer Binder on the Transparent Conducting Electrodes on Stretchable Film Fabricated by Screen Printing of Silver Paste