Abstract:Mesostructured silica SBA-15 materials with different structural parameters, such as pore size, pore volume, and wall thickness, etc., were prepared by varying the postsynthesis hydrothermal treatment temperature and adding inorganic salts. The hydrothermal stabilities of these materials in steam (100% water vapor) were systematically investigated using a variety of techniques including powder X-ray diffraction, transmission electron microscopy, nitrogen sorption, and (29)Si solid-state NMR. The effect of the pore size, microporosity or mesoporosity, and wall thickness on the stability was discussed. The results show that all of the SBA-15 materials have a good hydrothermal stability under steam of 600 degrees C for at least 24 h. N(2) sorption measurements show that the Brumauer-Emmett-Teller surface area of SBA-15 materials is decreased by about 62% after treatment under steam at 600 degrees C for 24 h. The materials with thicker walls and more micropores show relatively better hydrothermal stability in steam of 600 degrees C. Interestingly, we found that the microporosity of the mesostructured silica SBA-15 is a very important factor for the hydrothermal stability. To the materials with more micropores, the recombination of Si-O-Si bonds during the high-temperature steam treatment may not cause direct destruction to the wall structure. As a result, SBA-15 materials with more micropores show better stability in pure steam of 600 degrees C. Nevertheless, these materials are easily destroyed in steam of 800 degrees C for 6 h. Two methods to effectively improve the hydrothermal stability are introduced here: one is a high-temperature treatment, and another is a carbon-propping thermal treatment. Thermal treatment at 900 degrees C can enhance the polymerization degree of Si-O-Si bonds and effectively improve the hydrothermal stability of these SBA-15 materials in 800 degrees C steam for 12 h. But, this approach will cause very serious shrinkage of the mesopores, resulting in smaller pore diameter and low surface area. A carbon-propping thermal treating method was employed to enhance the polymerization of Si-O-Si bonds and minimize the serious shrinkage of mesopores at the same time. It was demonstrated to be an effective method that can greatly improve the hydrothermal stability of SBA-15 materials in 800 degrees C steam for 12 h. Furthermore, the SBA-15 materials obtained by using the carbon-propping method possess larger pores and higher surface area after the steam treatment at 800 degrees C compared to the materials from the direct thermal treatment method after the steam treatment.

Incorporation of Al3+ Ions to Promote the Stabilization Effect of (nh4)(2)sif6 Treatment on the Hydrothermal Stability of Mesoporous Sba-15 Zeolite

Improving the Hydrothermal Stability of Mesoporous Silica SBA-15 by Pre-treatment with (Nh4)2sif6

Facile Solvothermal Post-Treatment to Improve Hydrothermal Stability of Mesoporous SBA-15 Zeolite

Effects of residual alkali metals on the hydrothermal/thermal stability of silicalite-1

Highly hydrothermal stability of ordered mesoporous aluminosilicates Al-SBA-15 with high Si/Al ratio

The Search of Promoters for Silica Condensation and Rational Synthesis of Hydrothermally Stable and Well Ordered Mesoporous Silica Materials with High Degree of Silica Condensation at Conventional Temperature

Understanding of the High Hydrothermal Stability of the Mesoporous Materials Prepared by the Assembly of Triblock Copolymer with Preformed Zeolite Precursors in Acidic Media

Fluoride Ions Assistant Synthesis of Extremely Hydrothermal Stable Al-Sba-15 with Controllable Al Content

Creation Of Acid Sites On Sba-15 Mesoporous Silica By Alumination

Alumination and Ion Exchange of Mesoporous SBA-15 Molecular Sieves

Controllable and SDA-free synthesis of sub-micrometer sized zeolite ZSM-5. Part 1: Influence of alkalinity on the structural, particulate and chemical properties of the products

Prehydrolysis approach to direct synthesis of Fe, Al, Cr-incorporated SBA-15 with good hydrothermal stability and enhanced acidity

Insight into the construction of multi-cavity micro-mesoporous SSZ-13: Dissolution, Al backfilling and framework reconstruction

Enhanced acidity and hydrothermal stability of mesoporous aluminosilicate with secondary building units characteristic of zeolite Beta

The Influence of Adjacent Al Atoms on the Hydrothermal Stability of H-SSZ-13: a First-Principles Study.

Understanding Effect of Wall Structure on the Hydrothermal Stability of Mesostructured Silica SBA-15.

Studies on Modification and Structural Ultra-Stabilization of Natural STI Zeolite

Synthesis of hydrothermally stable, hierarchically mesoporous aluminosilicate Al-SBA-1 and their catalytic properties

Post-synthesis treatment of acid-made mesoporous silica materials by ammonia hydrothermal process

Effect of fluoride ions on the stability of SAPO-11 molecular sieves

Unravelling the Crucial of Spatial Al Distribution to Realize Precise Alkali‐Treatment for Target Acid‐Catalyzed Reactions