Abstract:This paper presents a climbing AUV, which is able to work in both swimming and climbing modes. The key issue in the design of a climbing robot is the choice of a reliable adhesion technique. Due to its great performance as regards payload, motion speed, simple system kinematics and gripping over a wide range of surfaces, a vortex-based suction cup is adopted to provide adhesion effect for the climbing motion of the AUV. Since the vortex-based suction cup is the core component of the vehicle, this paper mainly focuses on the structural and operational optimization of the suction cup by both Computational Fluid Dynamics (CFD) simulations and experimental validation. The proposed CFD simulation method is firstly verified by uncertainty study. The uncertainty analysis results indicate that the proposed simulation model and settings are reliable as reasonable agreements are found when comparing the computed results from varied grid size, iteration number, and time step cases. The total numerical uncertainties of the CFD simulation method for adhesion force and torque prediction are 1.50% and 1.46% of the average simulated values, respectively. In the CFD simulations, we investigate the effects of some key structural and operational parameters on the adhesion performance of the suction cup, including the vane number of impeller, the shape of cup shell, the adhesion gap (distance between cup bottom and wall surface), and the rotation rate of impeller. It can be concluded that more rotation rate of impeller can generate more adhesion force and more torque; smaller adhesion gap can produce more adhesion force but less torque; cup wall with inclined angle can increase the adhesion force and decrease the torque; the adhesion performance of the suction cup is less sensitive to the vane number of the impeller. CFD simulation results provide the basic design guidelines for the development of suction cup prototype. In the experiments, a specially designed testing platform is built up to validate and compare the performance of a set of suction cup prototypes, varied by different impeller and cup shell combinations. We compare the CFD simulation and experiment results of a 10-vane suction cup at a range of rotation rate conditions. The reasons of the discrepancy between CFD simulation and experiment results are mainly due to the open-loop control of the drive motor and the underestimate of the rotation rate in the experiments. The experimental results indicate that the effects of the structural and operational parameters on the generated adhesion performance are very complicated, and the effect of the structural parameters on the adhesion performance is influenced by the operational parameters, while the rotation rate and the adhesion gap play the key roles.

Development And Analysis Of An Electrically Activated Sucker For Handling Workpieces With Rough Surface

Development of a Pneumatic Sucker for Gripping Workpieces with Rough Surface

Optimization Design and Experimental Validation of a Vortex-Based Suction Cup for a Climbing AUV

A self-loading suction cup driven by a resonant dielectric elastomer actuator

Experimental comparison of Bernoulli gripper and vortex gripper

Design and Optimization of a Novel Swirling Sucker for Underwater Wall-Climbing Robots.

Study on the Optimal Design for Cavitation Reduction in the Vortex Suction Cup for Underwater Climbing Robot

Development of an Annular-Shaped Bernoulli Gripper for Contactless Gripping of Large-Size Silicon Wafer

The structure design of the end picker for the automobile control arm stamping production line

Study on the Adsorption Performance of a Vortex Suction Cup under Varying Diameters of Underwater Structure Tubes

Hydraulically Coupled Dielectric Elastomer Actuators for a Bioinspired Suction Cup

Design and Optimization of Self-Compensation Oil Distributor for Hydraulic Motors

A Performance Test and Internal Flow Field Simulation of a Vortex Pump

Numerical Simulation of Power Consumption and Mixing Characteristics of Novel Large-Double-blade Impeller

Development of a new gerotor for oil pumps with multiple profiles

Design and Optimization of Electropermanent Magnet Suckers in Horizontal Well Tractors

Development of an Underwater Cleaning Robot with Vortex Suction Mechanism

Analysis and numerical simulation of claw vacuum pumps with novel three-claw rotors

A Flexible Electrostatic Adsorption Suction Cup for Curved Surface

A Climbing Machining Robot for Large Components With Variable Curvature Surface

The development of a high-speed miniature pump with dynamic bearing