Abstract:The recycled copper alloy powders prepared by physical method were further alloyed, and therefore four medium entropy alloys (MEAs), (Fe40Ni40Mn20)(50)Cu-50, (Fe38Ni38Mn19Al5)(50)Cu-50, (Fe36Ni36Mn18Al10)(50)Cu-50 and (Fe32Ni32Mn16Al20)(50)Cu(50)were successfully prepared via mechanical alloying (MA) and spark plasma sintering (SPS). The influence of Al content on the microstructure and mechanical properties of the MEAs were systematically studied. Following 60 h of MA, the mechanical alloyed powders of the four MEAs consist of a primary supersaturated FCC solid solution along with a trace amount of WC contaminants. Following SPS, the (Fe40Ni40Mn20)(50)Cu-50, (Fe38Ni38Mn19Al5)(50)Cu-50 and (Fe36Ni36Mn18Al10)(50)Cu-50 show a dual-phase structure consisting of a Cu-rich phase (FCC1) and a Fe-Ni-rich phase (FCC2), displaying a multiscale grain structure of ultrafine grains and micron grains. However, the (Fe32Ni32Mn16Al20)(50)Cu-50 alloy shows a primary Cu-rich phase (FCC1) with a small amount of Fe-Mn rich phase (FCC2) and Ni-Al rich B2 phase. The plasticity of the four MEAs is gradually decreased, while the strength and hardness are gradually increased with the increase of Al content. The compressive yield strength, compressive strength and Vickers hardness of (Fe40Ni40Mn20)(50)Cu-50 MEAs are 878 MPa, 1257 MPa and 248.5HV, respectively. Compared with (Fe40Ni40Mn20)(50)Cu-50, the compressive yield strength and hardness of (Fe32Ni32Mn16Al20)(50)Cu-50 are increased by 50.1% and 50.4%, respectively, whereas the fracture strain is decreased from 19.55% to 8.31%.

Properties and sintering behaviors of Fe-Cu-Mn-C alloy

Effect of Mn content on the microstructure and mechanical properties of Fe-Cu -C sintered low-alloy steels

Study on the Mechanical Properties and Microstructure of Partially-diffuse Alloyed Fe-Cu-Ni-Mo-C Materials

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Effects of Cooling Rate and Carbon Content on Microstructure and Mechanical Properties of Fe-Cu-Ni-Mo-C Sintered Materials

Effect of Mn Content on Microstructure and Properties of Cu-Mn Alloys

Effect of Fe Content on the Microstructure and Properties of Mo-Cu Alloy

Sinter-hardening properties of partially-diffuse alloyed Fe-Cu-Ni-Mo-C material prepared by die wall lubricated warm compaction

Effect of Mn on microstructure and properties of Cu-12Al powder metallurgy alloy

Effect of small amount of Mo addition on microstructure and mechanical properties of Fe-0.5Mn-0.5C sintered steels

Formation of Fe-rich intermetallic compounds and their effect on the tensile properties of squeeze-cast Al–Cu alloys

Microstructure and mechanical properties of (FeNiMnAl<sub><i>x</i></sub>)<sub>50</sub>Cu<sub>50</sub> medium entropy alloy fabricated by powder metallurgy

STUDY ON THE SINTER-HARDENING PROPERTIES OF Fe-Cu-Ni-Mo-C MATERIALS BY WARM COMPACTION WITH WALL LUBRICATED DIE

Effects of Mn Content on Microstructures and Mechanical Properties of Al-5.0Cu-0.5Fe Alloys Prepared by Squeeze Casting

Microstructure and Mechanical Characteristics of Cu-12.5Ni-5Sn-xFe Sintered Alloys

Study on Mechanical Properties and Microstructure of Cu20Fe80 Alloy Using the Mechanical Alloying

Effece of Cu3P on microstructure and mechanical properties of Fe-2Ni-1Cu-0.6C double pressed/double sintered materials

Study on High Performance Warm Compacted Fe-2Ni-2Cu-1Mo-1C Powder Metallurgy Materials

Effect of Cu content on the microstructure and properties of sintered Fe-0.8C-xCu antifriction materials

Effect of Si content on microstructures and mechanical properties of Al-5.0Cu-0.6Mn-0.7Fe alloy prepared by squeeze casting