Abstract:Based on the preparation of nickel-plated zinc oxide (Ni-ZnO) by pyrolysis-reduction method, low silver Sn1.0Ag0.5Cu lead-free composite solders reinforced with Ni-ZnO were prepared by the powder metallurgy method, and the microstructure and properties of the soldering joints were investigated accordingly. The results showed that the particle size of ZnO was reduced after ball milling. The Ni-ZnO reinforcement phase was successfully prepared by pyrolysis-reduction method, in which Ni particles with an average particle size of 9.7 nm were uniformly and densely deposited on the surface of ZnO particles, and the interface between ZnO (002) and Ni (111) showed a semi-coherent relationship with a mismatch of 0.203. The moderate addition of Ni-ZnO had little effect on the electrical conductivity of the Sn1.0Ag0.5Cu composite solders reinforced with Ni-ZnO. But it refined the primary β-Sn grains in the composite solders and improved the wettability and tensile strength of the composite solders. At an addition of 1.0 wt.% Ni-ZnO reinforcement phase, the tensile strength and shear strength of the composite solder and its soldering joint reached a maximum value of 41.8 MPa and 28.9 MPa, with an increase of 39.3% and 41.7% respectively compared to the base solder material. The fracture position of composite solder/Cu soldering joint occurred in the transition zone of the soldering seam and IMC (Intermetallic Compound) layers. With the increase of Ni-ZnO reinforcement phase addition, the shear fracture location of the soldering joint moved from the near copper substrate side to the near soldering seam side in the transition zone, and the fracture mode gradually changed from a mixed ductile-brittle fracture to a typical ductile fracture dominated by parabolic toughness dimples.

A Study Of Sn-Pb-Re Solder

Study of SN-PR-RE solder

A study on plastic deformation resistance of Sn-Pb-RE solder

Mechanical Properties and Evolution Behaviors of Different Sn63Pb37 Solders Under Reliability Test

Properties and Reliability of Sn-Pb and Lead-Free Mixed Soldering

Study of New Types Lead-Free Solder Alloys of Sn-Ag-Cu-Al-Ni and Sn-Zn-Bi-In-P

Processing Treatment of a Lead-Free Sn–Ag–Cu–Bi Solder by Rapid Laser-Beam Reflowing and the Creep Property of Its Soldered Connection

Progress of study on the lead-free of high temperature Pb-rich solder

Investigation on properties of Pb-Sb-Re alloy

Study on Mechanical Property and Solder ability of SnAgCu System Lead-free Solder Alloy

Processing performance and microstructure of Sn-Zn based solders modified by Bi and mixed rare earth elements

INVESTIGATION ON PROPERTY OF Pb-Ca-Sn-Re ALLOY

Study on properties of low-Ag content Sn-Ag-Zn lead-free solders

Effect of Refl owing Atmosphere on Mechanical Properties of Sn-3.0Ag-0.5Cu Pb-free Solder Joints

Creep and Fatigue Behaviors of the Lead-Free Sn–Ag–Cu–Bi and Sn60Pb40 Solder Interconnections at Elevated Temperatures

Study on the properties of low silver Sn1.0Ag0.5Cu composite solder reinforced with nickel-plated zinc oxide and its soldering joint

Research Overview on the Electromigration Reliability of SnBi Solder Alloy

Effect of Sb Content on the Microstructure and Mechanical Properties of Eutectic SnPb Solder

Research and Development of Sn-Zn Lead-free Solder

Effect of Rare-Earth (La, Ce, and Y) Additions on the Microstructure and Mechanical Behavior of Sn-3.9Ag-0.7Cu Solder Alloy

Effects Of Solder Volume On Redeposition Of (Au,Ni)Sn-4 Intermetallics In Snagcu Solder Joints