Abstract:Based on the preparation of nickel-plated zinc oxide (Ni-ZnO) by pyrolysis-reduction method, low silver Sn1.0Ag0.5Cu lead-free composite solders reinforced with Ni-ZnO were prepared by the powder metallurgy method, and the microstructure and properties of the soldering joints were investigated accordingly. The results showed that the particle size of ZnO was reduced after ball milling. The Ni-ZnO reinforcement phase was successfully prepared by pyrolysis-reduction method, in which Ni particles with an average particle size of 9.7 nm were uniformly and densely deposited on the surface of ZnO particles, and the interface between ZnO (002) and Ni (111) showed a semi-coherent relationship with a mismatch of 0.203. The moderate addition of Ni-ZnO had little effect on the electrical conductivity of the Sn1.0Ag0.5Cu composite solders reinforced with Ni-ZnO. But it refined the primary β-Sn grains in the composite solders and improved the wettability and tensile strength of the composite solders. At an addition of 1.0 wt.% Ni-ZnO reinforcement phase, the tensile strength and shear strength of the composite solder and its soldering joint reached a maximum value of 41.8 MPa and 28.9 MPa, with an increase of 39.3% and 41.7% respectively compared to the base solder material. The fracture position of composite solder/Cu soldering joint occurred in the transition zone of the soldering seam and IMC (Intermetallic Compound) layers. With the increase of Ni-ZnO reinforcement phase addition, the shear fracture location of the soldering joint moved from the near copper substrate side to the near soldering seam side in the transition zone, and the fracture mode gradually changed from a mixed ductile-brittle fracture to a typical ductile fracture dominated by parabolic toughness dimples.

Study of SN-PR-RE solder

Mechanical Properties and Evolution Behaviors of Different Sn63Pb37 Solders Under Reliability Test

Study of New Types Lead-Free Solder Alloys of Sn-Ag-Cu-Al-Ni and Sn-Zn-Bi-In-P

Effect of Rare-Earth (La, Ce, and Y) Additions on the Microstructure and Mechanical Behavior of Sn-3.9Ag-0.7Cu Solder Alloy

INVESTIGATION ON PROPERTY OF Pb-Ca-Sn-Re ALLOY

Study on properties of low-Ag content Sn-Ag-Zn lead-free solders

Progress of study on the lead-free of high temperature Pb-rich solder

Investigation on properties of Pb-Sb-Re alloy

Research and Development of Sn-Zn Lead-free Solder

Study on the properties of low silver Sn1.0Ag0.5Cu composite solder reinforced with nickel-plated zinc oxide and its soldering joint

Research Overview on the Electromigration Reliability of SnBi Solder Alloy

Effect of Er on Microstructure and Mechanical Properties of Sn58bi Based Lead-Free Solder

Study on Shear Strength for Sn-3Ag-3Bi Solder Joint

Reliability study of industry Sn3.0Ag0.5Cu/Cu lead-free soldered joints in electronic packaging

Interfacial reaction and mechanical properties of Sn–Bi Cu core solder joints

The effect of chemical species in the lead frame materials on the interface microstructure between copper alloys and SnPb solder

Effect of Nano-Al2o3 Reinforcement on the Microstructure and Reliability of Sn–3.0Ag–0.5Cu Solder Joints

Effects of Nitrogen on Wettability and Reliability of Lead-Free Solder in Reflow Soldering

Study on the Properties of Sn–9Zn–xCr Lead-Free Solder

Effect Of Cr Content On The Microstructure And Properties Of Sn-9zn Base Lead-Free Solder

Intermetallic and tensile study of the newly developed Sn-2.0Ag-0.7Cu solder with addition of 0.5 wt.% zinc