Competitive Adsorption of Water Vapor with VOCs Dichloroethane, Ethyl Acetate and Benzene on MIL-101(Cr) in Humid Atmosphere

Shikai Xian,Ying Yu,Jing Xiao,Zhijuan Zhang,Qibin Xia,Haihui Wang,Zhong Li

DOI: https://doi.org/10.1039/c4ra10463c

IF: 4.036

2015-01-01

RSC Advances

Abstract:The existence of water vapor in the feed stream led to a sharp decrease in the VOCs working capacity due to its strong competitive adsorption on the surfaces of MIL-101.

What problem does this paper attempt to address?

Highly enhanced and weakened adsorption properties of two MOFs by water vapor for separation of CO2/CH4 and CO2/N2 binary mixtures

Shikai Xian,Junjie Peng,Zhijuan Zhang,Qibin Xia,Haihui Wang,Zhong Li

DOI: https://doi.org/10.1016/j.cej.2015.02.041

IF: 15.1

2015-01-01

Chemical Engineering Journal

Abstract:•Positive and negative effects of H2O vapor on CO2 adsorption of MOFs were reported.•Water vapor adsorbed on MIL-100(Fe) promoted formation of more CO2 adsorptive sites.•Adsorbed H2O made CO2 capacity and selectivity of MIL-100(Fe) increase by 150% and 200%.•Competitive adsorption of H2O badly weakened CO2 capacity and selectivity of MIL-101.
Functionalized Activated Carbon for Competing Adsorption of Volatile Organic Compounds and Water

Xuecheng Guo,Xinyong Li,Guoqiang Gan,Liang Wang,Shiying Fan,Penglei Wang,Shaomin Liu,Moses O Tadé

DOI: https://doi.org/10.1021/acsami.1c18507

2021-11-17

Abstract:The interfacial interaction of activated carbon with volatile organic compounds (VOCs) is seriously affected by water vapor. Therefore, it is vital to enhance the hydrophobic performance of activated carbon for expanding its application in industrial and environmental fields. Herein, a series of hydrophobic activated carbon was fabricated by tailored mixed siloxane and applied in dynamic competitive adsorption at 0, 50, and 90% humidity. Simultaneously, the diffusion molecular models and multicomponent adsorption experiments were used to study the adsorption and diffusion mechanisms. The hydrophobicity of activated carbon was significantly improved by loading of mixed siloxane, in which the equilibrium water absorption decreased from 21.9 to 7.2% and the contact angles increased by 70.10°. Meanwhile, dynamic competitive adsorption at different humidities indicated that the siloxane-functionalized activated carbons (SACs) showed much better competitive adsorption performances for VOCs than original activated carbon, which was further confirmed by the theoretical calculations of adsorption energy. In addition, a remarkable adsorption selectivity and reusability could be demonstrated to VOCs with different polarities on SACs. This study not only provides a new strategy for the hydrophobic modification of activated carbon materials but also offers theoretical guidance for the treatment of gas streams with significant water contents.

materials science, multidisciplinary,nanoscience & nanotechnology
Investigation of the competitive adsorption mechanism between typical volatile organic compounds (VOCs) and water vapor in waste gas emissions from the fermentation industry

Xiaolong Yao,Xinyue Liang,Yue Shi,Jingya Zhou,Wenwen Gong,Qingwei Bu

DOI: https://doi.org/10.1080/01496395.2024.2434541

IF: 2.799

2024-11-30

Separation Science and Technology

Abstract:The fermentation waste gas, characterized by high humidity and diverse volatile organic compounds (VOCs), poses challenges for adsorption in activated carbon devices. In this study, starch-based activated carbon was used as an adsorbent, targeting typical VOCs from fermentation industries-methyl mercaptan, toluene, and n -hexane. The adsorption behavior of water vapor and VOCs on the carbon interface was analyzed through adsorption experiments, structure characterization, and molecular simulations. Results showed that at 70% RH, the adsorption capacities of toluene and n -hexane experienced a reduction of 42.15% and 59.24% respectively compared to their respective capacities without water vapor at the breakthrough moment, while methyl mercaptan's capacity increased by 32.29% due to dissolution in condensed water within micropores. Water displaced all three VOCs during multicomponent adsorption. Reducing surface carboxyl groups, pyrrolic-N, and pyridinic-N enhances selective adsorption of VOCs. Among the VOCs, toluene shows the strongest interaction with activated carbon, followed by n -hexane and then methyl mercaptan. However, a water film under high humidity hinders the adsorption of n -hexane and toluene, reducing selectivity. These research findings will contribute to a comprehensive understanding of the mechanisms underlying the absorption of VOCs in high humidity environments by activated carbon.

engineering, chemical,chemistry, multidisciplinary
Adsorption characteristics of water vapor on the hypercrosslinked polymeric adsorbent

Chao Long,Ying Li,Weihua Yu,Aimin Li

DOI: https://doi.org/10.1016/j.cej.2011.11.019

IF: 15.1

2012-01-01

Chemical Engineering Journal

Abstract:Hypercrosslinked polymeric adsorbent is finding increased application as sorbents for removing the VOCs from gas steam. Due to the competitive adsorption between the water and VOCs, hence, it is important to understand the adsorption characteristics of water vapor on hypercrosslinked polymeric adsorbent. In this paper, the adsorption of water vapor on hypercrosslinked polymeric adsorbent with poly (styrene-divinylbenzene) matrix (HY-1) was investigated and compared with a commercial activated carbon (m-GAC) and activated carbon fiber (ACF). The results showed that HY-1 had minimal uptake of water until P/P 0 was raised to 0.6, which is an indication of an extremely hydrophobic surface. Moreover, increasing the temperature induced the decrease of the water uptake and a rightward shift in the isotherm heel. The adsorption isotherms of water vapor on three adsorbents were fitted by the Cluster Formation Induced Micropore Filling model (CIMF model). The results indicated that the experimental data can be well-fitted by CIMF model. Based on this semiempirical modeling, the adsorptive contributions of primary sites and micropores were estimated qualitatively. In addition, the effect of water vapor on the adsorption of benzene onto three adsorbents was investigated. The breakthrough time of benzene on HY-1 decreased by 10.4% even if the relative humidity was 80%, while that of m-GAC and ACF decreased by17.2% and 38.9%, respectively. Therefore, HY-1 would be a particularly efficient and competitive adsorbent for VOCs recovery from the humid gas streams. © 2011 Elsevier B.V.
Adsorption/desorption of Toluene on a Hypercrosslinked Polymeric Resin in a Highly Humid Gas Stream

Bing Zhou,Bin Sun,Wenjuan Qiu,Ying Zhou,Junqian He,Xiao'ai Lu,Hanfeng Lu

DOI: https://doi.org/10.1016/j.cjche.2018.09.027

IF: 3.8

2018-01-01

Chinese Journal of Chemical Engineering

Abstract:In many sources of volatile organic compounds (VOCs), large amounts of water vapor come from the air and the reactors. The relative humidity (RH) of exhaust gas is normally >60% and is supersaturated. Maintaining the property of adsorbent on VOCs in a highly humid gas stream is a serious industrial problem. In this study, the adsorption/desorption behavior of toluene in a micro-mesoporous polymeric resin was investigated in a highly humid environment to explore the influence of abound water vapor on resin adsorption and regeneration. This resin could selectively adsorb toluene at an RH of 80%, and its adsorption property was unaffected by the presence of water vapor. In the case of humidity saturation, the resin displayed a high adsorption capacity at a moisture content of <30%. Therefore, the polymer resin is an excellent water-resistant adsorbent of VOCs. In the regenerative experiment, the resin maintained its original adsorption capability after four adsorption/desorption cycles of toluene purging with nitrogen gas at 120 degrees C. The resin exhibited excellent regeneration performance at high humidity. (C) 2018 The Chemical Industry and Engineering Society of China, and Chemical Industry Press Co., Ltd. All rights reserved.
Experimental investigation on water vapor adsorption performance of solvent-free synthesized MIL-100(Fe) and its composite adsorbent

Huizhong Zhao,Qingge Wang,Zhihao Xi,Chengfeng Liu,Chunbo Miao

DOI: https://doi.org/10.1016/j.jssc.2023.124135

IF: 3.3

2023-05-01

Journal of Solid State Chemistry

Abstract:With high hydrothermal stability and hydrophilicity, MIL-100(Fe) has potential applications in sorption-based atmospheric water harvesting (SAWH). This paper reports the water vapor adsorption properties of MIL-100(Fe) prepared by solvent and solvent-free methods. Performance tests show that the MIL-100(Fe) prepared by solvent-free method has more advantages. To further improve the performance of the adsorbent, the composite adsorbent MgCl2@MIL-100(Fe) was obtained by impregnating MIL-100(Fe) with MgCl2 solution. The results showed that the composite adsorbent had good adsorption performance, desorption properties, and fast adsorption rate. The equilibrium adsorption capacities of the composite adsorbent with 35% salt content were 0.533 g/g and 1.062 g/g at 25 °C with the relative humidity (RH) of 35% and 80%, respectively, which were 1.51 times and 1.74 times of the adsorption capacity of MIL-100(Fe) under the same working conditions. This showed that the solvent-free synthesized MIL-100(Fe) and its composite adsorbent have the potential for application in SAWH.

chemistry, physical, inorganic & nuclear
Experimental Study on Activated Carbon-MIL-101(Cr) Composites for Ethanol Vapor Adsorption

Zhongbao Liu,Jiayang Gao,Xin Qi,Zhi Zhao,Han Sun

DOI: https://doi.org/10.3390/ma14143811

IF: 3.4

2021-07-08

Materials

Abstract:In this study, the hydrothermal method was used to synthesize MIL-101(Cr), and activated carbon (AC) with different content was incorporated in to MIL-101(Cr), thereby obtaining AC-MIL-101(Cr) composite material with a huge specific surface area. The physical properties of MIL-101(Cr) and AC-MIL-101(Cr) were characterized by powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), nitrogen adsorption and desorption and specific surface area testing, and ethanol vapor adsorption performance testing. The results show that with the increase of activated carbon content, the thermal stability of AC-MIL-101(Cr) is improved. Compared with the pure sample, the BET specific surface area and pore volume of AC-MIL-101(Cr) have increased. In the relative pressure range of 0–0.4, the saturated adsorption capacity of AC-MIL-101(Cr) to ethanol vapor decreases slightly. It is lower than MIL-101(Cr), but its adsorption rate is improved. Therefore, AC-MIL-101(Cr)/ethanol vapor has a good application prospect in adsorption refrigeration systems. The exploration of AC-MIL-101(Cr) composite materials in this paper provides a reference for the future application of carbon-based/MOFS composite adsorbent/ethanol vapor working fluid in adsorption refrigeration.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Performance of MIL-101(Cr)/Water Working Pair Adsorption Refrigeration System Based on a New Type of Adsorbent Filling Method

Zhongbao Liu,Banghua Zhao,Longqian Zhu,Fengfei Lou,Jiawen Yan

DOI: https://doi.org/10.3390/ma13010195

IF: 3.4

2020-01-02

Materials

Abstract:MIL-101(Cr) and water were applied to adsorption refrigeration technology. MIL-101(Cr) was prepared by hydrothermal synthesis method and characterized by X-ray diffraction patterns (XRD), Fourier transform infrared spectroscopy (FTIR), N2 adsorption–desorption measurement at 77 K, thermal gravimetric analysis (TGA) and scanning electron microscope (SEM). The adsorption isotherms of water vapor on MIL-101(Cr) were investigated by using a gravimetric water sorption analyzer. This study established the basic adsorption cycle mathematical model and used MATLAB/Simulink for the simulation. The control variable method was used to simulate the effect on the cooling capacity and coefficient of performance (COP) when the desorption temperature changed. When the adsorption temperature was 35 °C, the evaporation temperatures were 15 °C and 20 °C, and the amount of water vapor equilibrium adsorption on MIL-101 (Cr), Cooling power per unit adsorbent mass (SCP), and COP were measured by using the adsorption performance test rig on the basis of a new type of powder adsorbent filling method.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Understanding the Adsorption Kinetics of Acetone in Humid Activated Carbons: Perspectives from Adsorption-Breakthrough Experiments and Molecular Simulations

Shanshan Wang,Jianggen Hu,Licheng Li,Songlin Zuo

DOI: https://doi.org/10.1021/acsomega.4c02262

IF: 4.1

2024-10-07

ACS Omega

Abstract:The presence of water vapor influences the adsorption equilibrium and kinetics of volatile organic compounds (VOCs) in porous materials. By combination of breakthrough experiments and molecular simulations, the competitive adsorption mechanisms of water vapor and acetone on activated carbon with different textures and surface chemical properties at different humidity levels were investigated. Adsorption capacity decreases with increasing relative humidity owing to the formation of preferential...

chemistry, multidisciplinary
Behavior of VOCs competitive adsorption with water vapor in a slit-shaped phosphoric acid mesoporous activated carbon model

Tangying Cheng,Jinjin Li,Xiuwei Ma,Lei Zhou,Hao Wu,Linjun Yang

DOI: https://doi.org/10.1016/j.seppur.2023.124776

IF: 8.6

2023-08-26

Separation and Purification Technology

Abstract:Pistachio shells were activated with H 3 PO 4 , and mesoporous activated carbon (AC) was pyrolyzed and prepared at high temperature. The impacts of phosphoric acid concentrations on the structure, physicochemical properties, and VOC adsorption performance of ACs were investigated. The results indicated that the specific surface area, average pore size, and surface P content of 20% phosphoric acid AC reached 1031.8 m 2 ·g −1 , 4.16 nm, and 3.87%, respectively. With increasing phosphoric acid concentration, the microporosity and graphitization of the ACs decreased, and the average pore size and P content of the ACs increased. The adsorption performance of PSAC-1P and PSAC-2P for VOCs in high-humidity exhaust gas was the most favorable. grand canonical Monte Carlo (GCMC) calculations revealed that at a relative humidity of 80%, water molecules and VOCs were adsorbed on the graphite-structured carbon surface in turn. The larger the pore size, the easier it was for water molecules to aggregate, and the adsorption sites were occupied by water molecules. P-functional groups effectively inhibited water molecular clusters from forming water clusters, benefitting from the mesopore adsorption of VOCs in competition with water vapor. The findings provide significant support for the effective adsorption treatment of VOCs in high-humidity exhaust gas.

engineering, chemical
Superior pore size for enhancing the competitive adsorption of VOCs under high humid conditions: An experiment and molecular simulation study

Jinjin Li,Yin Yin,Tangying Cheng,Heng Chen,Linjun Yang,Hao Wu

DOI: https://doi.org/10.1016/j.jece.2023.111091

IF: 7.7

2023-09-29

Journal of Environmental Chemical Engineering

Abstract:Water vapor greatly decreases the adsorption capacity of activated carbons (AC) for low-concentration volatile organic compounds (VOCs) under high humid conditions. However, the design and synthesis of AC with high adsorption selectivity for VOCs/water vapor still remains a challenge. In this paper, a hydrophobic hierarchical porous AC was synthesized by using g-C 3 N 4 as the pore-forming agent and the roles of pore sizes on the competitive adsorption were studied by experiments and simulation calculations. The results showed that pore size of 0.59–1.50 nm had a stronger correlation with toluene dynamic adsorption capacity. The largest adsorption capacity of single toluene and water vapor occurred in the 1.0 nm and 0.7 nm slit pore, respectively. During the toluene adsorption at 70 RH%, the superior pore size was 0.7–1.30 nm, and the maximum value appeared in the 1.0 nm pore without pore condensation of water clusters. Furthermore, a quantitative relationship that the superior pore size of VOCs at 70 RH% was 0.86–1.52 S (S is the longest distance of VOCs molecule) was summarized. In addition, a lower surface oxidation degree would broaden superior pore size range. This study provides a theoretical preference for designing AC for target VOCs removal from high humid conditions.

engineering, chemical, environmental
Engineering surface functional groups on mesoporous silica: towards a humidity-resistant hydrophobic adsorbent

Shuai Liu,Yue Peng,Jianjun Chen,Wenbo Shi,Tao Yan,Bing Li,Yani Zhang,Junhua Li

DOI: https://doi.org/10.1039/c8ta04082f

IF: 11.9

2018-01-01

Journal of Materials Chemistry A

Abstract:Practical volatile organic compound (VOC) adsorption requires the functional materials to work in humid conditions, whereas most proposed materials fail to overcome this challenge. We report a facile thermal treatment approach to create an organic functional group-enriched and hydroxyl group-limited mesoporous silica, that exhibits dramatically improved humidity resistance and toluene adsorption capacity. Fundamental adsorption behaviors of the materials were investigated both statically and dynamically to distill the functional mechanisms of the performance enhancement. In particular, the results of adsorption heat demonstrated their hydrophobicity and strong affinity to toluene, and dynamic adsorption tests illustrated a higher adsorption selectivity for toluene (with 1.39-1.84 times the hydrophobicity values of Q(wet)/Q(dry) (76.4-71.5%) compared with pristine silica) and reusability, which were both attributed to the durable and stable surface hydrophobicity.
Adsorption of volatile organic compounds over MIL-125-NH2

Bomi Kim,Yu-Ri Lee,Hee-Young Kim,Wha-Seung Ahn

DOI: https://doi.org/10.1016/j.poly.2018.08.010

IF: 2.975

2018-11-01

Polyhedron

Abstract:Volatile organic compounds (VOCs) cause environmental and health problems by forming photochemistry smog, and development of an effective adsorbent for their removal is important. In this work, adsorption of a series of selected VOCs over an amine-functionalized metal organic framework, MIL-125-NH2, was investigated by measuring their adsorption isotherms at three different temperatures. Significant amounts of the VOCs were adsorbed, and their adsorption capacities increased with the increasing order of polarity (p-xylene < toluene < benzene < acetone < isopropanol). In addition, formaldehyde breakthrough capacities were measured and MIL-125-NH2, exhibited a clearly superior performance to other MOFs, probably because of the synergistic effects provided by the amine groups that strongly interacting with the formaldehyde and the small micropores in MIL-125-NH2.

chemistry, inorganic & nuclear,crystallography
Effect analysis of temperature and initial water content on the adsorption and separation of VOCs by ZIF‐8 based on molecular simulation

Xiaotong Li,Yongyin Zheng,Weiqiu Huang,Xufei Li,Xinya Wang,Lin Liu,Jing Zhong,Fangrui Feng

DOI: https://doi.org/10.1002/app.55854

IF: 3

2024-06-10

Journal of Applied Polymer Science

Abstract:This study investigated the effects of changes in two environmental conditions, temperature and initial water content, on the gas adsorption performance of ZIF‐8. The effects of changes in environmental conditions on the adsorption performance were measured through parameters such as adsorption capacity, adsorption heat, threshold pressure and single molecule interaction energy. Volatile organic compounds (VOCs) have seriously polluted the atmospheric environment and caused harmful effects on human beings, so it is imperative to control oil vapor emissions. Metal organic framework materials, as one of the porous materials, have a good application prospect in the field of gas adsorption separation. In this paper, the effects of temperature and initial water content (IWC) on the adsorption properties of methane (CH4), ethane (C2H6), ethylene (C2H4), propane (C3H8), and propylene (C3H6) by ZIF‐8 were studied by combining the large gauge Monte Carlo (GCMC) and ideal adsorption solution theory. The results show that the higher the temperature is, the lower the adsorption capacity is, the higher the threshold pressure is, and the single molecule interaction energy changes little with temperature. But pore volume is still the main influencing factor. The IWC also reduces the saturated adsorption capacity. Preloaded water molecules can enhance the electrostatic interaction at low pressure, thus affecting the adsorption heat and interaction energy of single molecules. Overall, these findings provide valuable mechanistic insights into the effects of temperature and IWC on the adsorption properties of ZIF‐8 for VOCs.

polymer science
Adsorption of Multicomponent VOCs on Various Biomass-Derived Hierarchical Porous Carbon: A Study on Adsorption Mechanism and Competitive Effect.

Xinlei Huang,Minghui Tang,Hongxian Li,Ling Wang,Shengyong Lu

DOI: https://doi.org/10.1016/j.chemosphere.2022.137513

IF: 8.8

2022-01-01

Chemosphere

Abstract:Biomass-derived porous carbon materials are potential adsorbents for VOCs. In this work, biomass-derived nitrogen-doped hierarchical porous carbons (NHPCs) were synthesized by a one-step pyrolysis activation combined with nitrogen doping method from several biomass wastes (corn straw, wheat stalk, bamboo, pine, and corncob). NHPCs have a hierarchical porous structure with micro-meso-macropores distribution, nitrogen doping, large specific surface area, and pore volume. The corncob derived carbon (NHPC-CC) has the best activation result as analyses showed that a lower ash content and higher total cellulose composition content of the biomass result in a better pore activation effect. Single and multi-component dynamic adsorption tests of typical VOCs (benzene, toluene, and chlorobenzene) were conducted on NHPCs in laboratory conditions (∼500 ppm). Promising VOC adsorption capacity and great adsorption kinetics with low mass transfer resistance were found on NHPCs. Correlation analysis showed that the high VOC adsorption capacity and great adsorption kinetics can be attributed to the large surface area of micro-mesopores and the mass transfer channels provided by meso-macropores respectively. The competitive dynamic adsorption tests revealed that the VOC with lower saturated vapor pressure has more adsorption sites on the surface of micro-mesopores and stronger adsorption force, which results in the higher adsorption capacity and desorption caused by substitution reaction in VOCs competitive adsorption process. In detail, the process of toluene and chlorobenzene competitive adsorption was described. Besides, well recyclability of NHPC-CC was revealed as the VOCs adsorption capacity reductions were less than 10% after four adsorption-desorption cycles. All studies showed that the NHPC-CC could be potential adsorbent for VOCs in industrial process.
The Design of Core–shell ZSM-5@NiAl-LDH Composites for Efficient Adsorption of VOCs under High Humidity

Wei Zhao,Yinan Xu,Yuehui Qiao,Rui Sun,Jie Qian,Yixue Wang,Quan Liu,Zhekun Shi,Fandong Meng,Xiaoli Zhan,Qinghua Zhang

DOI: https://doi.org/10.1016/j.seppur.2024.129729

IF: 8.6

2025-01-01

Separation and Purification Technology

Abstract:Zeolites have been widely utilized in the adsorption of volatile organic compounds (VOCs) due to their high specific surface area and robust stability. However, the adsorption capacity of zeolites for VOCs is considerably reduced under humid conditions due to the competitive adsorption between water and VOCs, thereby limiting their industrial applicability. Herein, we report a core-shell ZSM-5@NiAl-LDH (Z-L) composites designed specifically for efficient adsorption of VOCs under high humidity conditions. The core-shell architecture is achieved by introducing active sites onto the ZSM-5 framework pretreated with high-alkalinity agents, followed by the growth of NiAl-LDH on its surface, creating a regular, vertically staggered structure. Compared with ZSM-5 zeolite, Z-L composites show a larger specific surface area, wider pore size, and larger mesopore volume, allowing a high adsorption capacity of the VOCs. Contact angle and static adsorption tests of water molecules reveal that the LDH shell effectively increases the hydrophobicity of Z-L composites. The dynamic adsorption behavior for m-xylene demonstrates that Z-L composites exhibit significantly enhanced adsorption capacity, 3.79 times that of ZSM-5 zeolite. Furthermore, Z-L composites exhibit a higher selectivity for m-xylene at 60 % relative humidity, achieving a Q(wet )/Q(dry) ratio of 86.7 %, outperforming most porous adsorption materials. Kinetic model analysis reveals that the augmentation of mesopores in Z-L composites enhances the effective diffusion space for synthesized samples, resulting in exceptional adsorption performance. This novel synthetic material is anticipated to be a promising candidate for VOCs pollution control in high-humidity environments.
Practical strategies to address the moisture barriers in the adsorption of aromatic volatile organic compounds in air

Mingshen Yu,Botao Liu,Younes Ahmadi,Ki-Hyun Kim

DOI: https://doi.org/10.1016/j.mattod.2024.08.022

IF: 24.2

2024-09-16

Materials Today

Abstract:Aromatic volatile organic compounds (AVOCs) are well-known pollutants that exist ubiquitously in both indoor and outdoor environments. Adsorption is yet employed most preferably for the mitigation of AVOCs with multiple merits (e.g., facile operation and low cost) among various technological options developed based on recovery or destruction principles. The adsorption of AVOCs is generally suppressed by the presence of other components like water vapor, while their interactions can also have a positive effect (e.g., in terms of reverse polarities such as between (polar) water and (non or weakly polar) AVOCs). It is thus possible to considerably improve the removal potential (e.g., adsorption capability and selectivity) of sorbents against AVOCs even under wet conditions. In this review, the basic aspects of AVOC adsorption in the presence of water vapor are discussed using benzene and toluene as model compounds. In this context, AVOC removal performance of adsorbents is assessed between wet and dry conditions in terms of adsorption capacity (Q), partition coefficient (PC), and capacity retention (Q wet /Q dry ) after being sorted into three groups (i.e., AC-based, MOF-based, and miscellaneous adsorbents). As a result, a number of adsorbents with suitable pore size, high hydrophobicity, or abundant functional groups (e.g., BUT-55 and AC-MA) are identified to perform well under both dry and humid conditions. This study offers forward-looking insights into the establishment of advanced strategies to design high-performance sorbent materials against AVOCs under real-world humid conditions.

materials science, multidisciplinary
Experimental study on salt–metal organic framework composites for water absorption

Zhongbao Liu,Wenqi Gao,Xin Qi,Fengfei Lou,Huiwei Lang

DOI: https://doi.org/10.1016/j.ica.2019.119214

IF: 3.118

2020-01-01

Inorganica Chimica Acta

Abstract:In this article, MIL-101(Cr) powder material was successfully prepared by hydrothermal synthesis and combined with different mass fractions of CaCl2 by immersion method to obtain MIL-101(Cr)/CaCl2 composite materials. The physical properties of the adsorbent were determined by X-ray powder diffraction, N2 adsorption/desorption isotherm, TGA and FTIR. The water vapor adsorption performance of MOFs was tested by a gravimetric instrument to analyze the underlying mechanism. Results indicated that the specific surface area, total pore volume, and pore size distribution of micropores and mesopores of MIL-101(Cr)/CaCl2 composites decreased with increasing CaCl2 content. When P/P0 = 0.9, the water vapor equilibrium adsorption capacities of MIL-101(Cr), MIL-101(Cr)/CaCl2-10%, MIL-101(Cr)/CaCl2-20%, and MIL-101(Cr)/CaCl2-30% were 1.05, 0.88, 1.13, and 1.35 g/g, respectively. MIL-101(Cr)/CaCl2-30% agglomerated after water absorption, so MIL-101(Cr)/CaCl2-20% was selected as the final experimental material. The water vapor adsorption heat of MIL-101(Cr)/CaCl2-20% was 42–58 kJ/mol, which is close to the evaporation enthalpy of water (44 kJ/mol at 25 °C). The analysis of the adsorption kinetics showed the relatively uniform adsorption rate of MIL-101(Cr)/CaCl2-20%. Overall, MIL-101(Cr)/CaCl2-20% exhibited superior water vapor adsorption performance and have great potential for application to adsorption heat pumps.

chemistry, inorganic & nuclear
Trimethylchlorosilane Modified Activated Carbon for the Adsorption of VOCs at High Humidity

Zhirui Li,Yuqi Jin,Tong Chen,Feng Tang,Jie Cai,Jiayu Ma

DOI: https://doi.org/10.1016/j.seppur.2021.118659

IF: 8.6

2021-01-01

Separation and Purification Technology

Abstract:Water vapor is inevitable in practical volatile organic compounds (VOCs) exhaust emission, leading to the deterioration of activated carbon adsorption performance. A hydrophobic modification method of activated carbon (AC) using tetraethyl orthosilicate (TEOS) and trimethylchlorosilane (TMCS) was developed to improve the selectivity of VOCs. A series of characterization and toluene dynamic adsorption experiments at the relative humidity (RH) between 0% and 90% were conducted to find the optimal condition of TMCS and evaluate the modification method. The results showed that TEOS constructed -Si-O-Si- structure and introduced Si-OH to react with TMCS. 30%(w/w) TMCS impregnation for 24 h was an appropriate condition, which improved the water contact angle from 111.6 degrees to 143.6 degrees. When the RH increased from 0% to 60% and 90%, the saturated adsorption capacity of Bare-AC decreased by 45% and 64%, respectively. However, for the TMCS modified activated carbon, the decreases could reduce to only 6% and 9%. At high humidity, the improvement in hydrophobicity compensated the damage of microstructure and provided 52% better toluene adsorption capacity at RH 60%, and 91% better at RH 90%.
Experimental investigation of the dehumidification and decarburization performance of metal-organic frameworks in solid adsorption air conditioning

Liu Chen,Famei Yang

DOI: https://doi.org/10.1039/d2ra07209b

2023-01-03

Abstract:Solid adsorption air conditioning systems use solid adsorption materials to co-adsorb water vapor and carbon dioxide, allowing the humidity and carbon dioxide concentration in the air-conditioned room to be controlled. Exploring the co-adsorption mechanism of H2O and CO2 is essential for the screening of adsorbent materials, system design, and system optimization in solid adsorption air conditioning systems. A fixed-bed adsorption-desorption device was built, and the dynamic adsorption properties of three MIL adsorbent materials MIL-101(Cr), MIL-101(Fe), and MIL-100(Fe) for co-adsorption of H2O and CO2 were studied. The results showed that all three MIL adsorbent materials are capable of performing co-adsorption of H2O and CO2 and meet the requirements of solid adsorption air conditioning systems. MIL-101(Cr) is recommended for solid adsorption air conditioners where dehumidification is the main focus, while MIL-100(Fe) is recommended for solid adsorption air conditioners where carbon removal is the main focus.

Competitive Adsorption of Water Vapor with VOCs Dichloroethane, Ethyl Acetate and Benzene on MIL-101(Cr) in Humid Atmosphere

Highly enhanced and weakened adsorption properties of two MOFs by water vapor for separation of CO2/CH4 and CO2/N2 binary mixtures

Functionalized Activated Carbon for Competing Adsorption of Volatile Organic Compounds and Water

Investigation of the competitive adsorption mechanism between typical volatile organic compounds (VOCs) and water vapor in waste gas emissions from the fermentation industry

Adsorption characteristics of water vapor on the hypercrosslinked polymeric adsorbent

Adsorption/desorption of Toluene on a Hypercrosslinked Polymeric Resin in a Highly Humid Gas Stream

Experimental investigation on water vapor adsorption performance of solvent-free synthesized MIL-100(Fe) and its composite adsorbent

Experimental Study on Activated Carbon-MIL-101(Cr) Composites for Ethanol Vapor Adsorption

Performance of MIL-101(Cr)/Water Working Pair Adsorption Refrigeration System Based on a New Type of Adsorbent Filling Method

Understanding the Adsorption Kinetics of Acetone in Humid Activated Carbons: Perspectives from Adsorption-Breakthrough Experiments and Molecular Simulations

Behavior of VOCs competitive adsorption with water vapor in a slit-shaped phosphoric acid mesoporous activated carbon model

Superior pore size for enhancing the competitive adsorption of VOCs under high humid conditions: An experiment and molecular simulation study

Engineering surface functional groups on mesoporous silica: towards a humidity-resistant hydrophobic adsorbent

Adsorption of volatile organic compounds over MIL-125-NH2

Effect analysis of temperature and initial water content on the adsorption and separation of VOCs by ZIF‐8 based on molecular simulation

Adsorption of Multicomponent VOCs on Various Biomass-Derived Hierarchical Porous Carbon: A Study on Adsorption Mechanism and Competitive Effect.

The Design of Core–shell ZSM-5@NiAl-LDH Composites for Efficient Adsorption of VOCs under High Humidity

Practical strategies to address the moisture barriers in the adsorption of aromatic volatile organic compounds in air

Experimental study on salt–metal organic framework composites for water absorption

Trimethylchlorosilane Modified Activated Carbon for the Adsorption of VOCs at High Humidity

Experimental investigation of the dehumidification and decarburization performance of metal-organic frameworks in solid adsorption air conditioning