Large-scale Aligned Crystalline CH3NH3PbI3 Perovskite Array Films

Yitan Li,Xiao Wang,Shiting Wu,Haina Ci,Henglu Xu,Xuemei Li,Hao Sun,Zeyao Zhang,Anyuan Cao,Xuefeng Guo,Yan Li

DOI: https://doi.org/10.1039/c5ta04936a

2015-01-01

Journal of Materials Chemistry

Abstract:Owing to the lattice match, large-scale aligned crystalline CH3NH3PbI3 perovskite array films were fabricated on ST cut quartz.

What problem does this paper attempt to address?

Epitaxial Growth of Horizontally Aligned Single-Crystal Arrays of Perovskite

Yitan Li,Yuguang Chen,Lu Han,Xuemei Li,Jian Sheng,Hao Sun,Yan Li

DOI: https://doi.org/10.1007/s40843-018-9304-7

2018-01-01

Science China Materials

Abstract:Well-aligned single-crystal nanowire arrays of CH3NH3PbI3 have shown potentials in laser sources and photovoltaic applications. Here we developed a solution based epitaxial method to grow CH3NH3PbI3 nanowire arrays. By confining the precursor solution between a silicon wafer and ST-cut quartz, the evaporation rate of the solvent was slowed down which brings a more stable and controllable solution environment. Relying on the lattice match between CH3NH3PbI3 and ST-cut quartz, arrays of single-crystal nanowires of CH3NH3PbI3 have been grown epitaxially. The densities and lengths of CH3NH3PbI3 nanowires can be tuned. The lengths of the resultant crystals range from several microns to over one millimeter. Such CH3NH3PbI3 arrays with good alignment and crystallinity were then applied to fabricate photovoltaic devices with good performances.
Thermally Induced Crystallization of High Quality CH3 NH3 PbI3 Film with Large Grains for Highly Efficient Perovskite Solar Cells.

Yu Hou,Shuang Yang,Xiao Chen,Chunzhong Li,Huijun Zhao,Hua Gui Yang

DOI: https://doi.org/10.1002/chem.201605693

2017-01-01

Chemistry - A European Journal

Abstract:Recently, fully covered and smooth perovskite films could be fabricated by optimized coating methods; however, it is still hard to prepare perovskite films with large grain sizes and high crystallinity. Given the fact that thermal energy can promote crystallization, we combine high-temperature crystallization with the application of a solvent featuring a high boiling point, in order to produce high quality perovskite films with micrometer-sized grains. We further investigated the temperature dependence of the thermally induced synthetic strategy, whereby the grains become larger as the temperature is elevated. After solar cell device fabrication, the efficiency of the best cell can attain a high value of 15.53 % with reduced hysteresis behavior.
Pseudohalide-Induced Recrystallization Engineering for CH3NH3PbI3 Film and Its Application in Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

Hua Dong,Zhaoxin Wu,Jun Xi,Xiaobao Xu,Lijian Zuo,Ting Lei,Xingang Zhao,Lijun Zhang,Xun Hou,Alex K. -Y. Jen

DOI: https://doi.org/10.1002/adfm.201704836

IF: 19

2017-01-01

Advanced Functional Materials

Abstract:High crystallinity and compactness of the active layer is essential for metal-halide perovskite solar cells. Here, a simple pseudohalide-induced film retreatment technology is developed as the passivation for preformed perovskite film. It is found that the retreatment process yields a controllable decomposition-to-recrystallization evolution of the perovskite film. Corresponding, it remarkably enlarges the grain size of the film in all directions, as well as improving the crystallinity and hindering the trap density. Meanwhile, owing to an intermediate catalytic effect of the pseudohalide compound (NH4SCN), no crystal orientation changing and no impurity introduction in the modified film. By integrating the modified perovskite film into the planar heterojunction solar cells, a champion power conversion efficiency of 19.44% with a stabilized output efficiency of 19.02% under 1 sun illumination is obtained, exhibiting a negligible current density-voltage hysteresis. Moreover, such a facile and low-temperature film retreatment approach guarantees the application in flexible devices, showing a best power conversion efficiency of 17.04%.
Reproducible One-Step Fabrication of Compact MAPbl(3-x)Cl(x) Thin Films Derived from Mixed-Lead-Halide Precursors

Dong Wang,Zhihong Liu,Zhongmin Zhou,Huimin Zhu,Yuanyuan Zhou,Changshui Huang,Zaiwei Wang,Hongxia Xu,Yizheng Jin,Bin Fan,Shuping Pang,Guanglei Cui

DOI: https://doi.org/10.1021/cm5037869

IF: 10.508

2014-01-01

Chemistry of Materials

Abstract:Methylammonium lead trihalide perovskites are attracting intensive interest due to its high photovoltaic performance, low cost and one-step solution processability. Since the morphology of the perovskite thin films play the central role on the cell performance, a plethora of methods have been developed to fabricate uniform perovskite film. Herein, we demonstrate that an innovative approach by applying mixed lead salts (PbI2 + PbCl2) to facilitate reproducible fabrication of compact perovskite thin film. It is proposed that rapid reaction kinetics of PbI2 with MAI enables preformation of perovskite within the intermidiate film matrix, working as homogeneously located domains for squential growth of the PbCl2-derived perovskite. The as-prepared perovskite film exhibited a overall textured crystal morphology and superior compactness, which enables excellent light absorption and long-time preservation of photogenerated charge carriers and therefore exhibits 11% efficiency in planar-structured solar cells. The annealing testing shows the film also possesses very stable morphology upon long-time heating, indicative of the insensitivity of our new protocol to the preparation condition and also the promising thermal stability of its based solar cells. The simplicity of the one-step solution-processing and the high morphology stability of the as-prepared perovskite film endow this mixing lead salts method with feasibility of the large-scale fabrication.
Large-Area Synthesis and Patterning of All-Inorganic Lead Halide Perovskite Thin Films and Heterostructures

Yiliu Wang,Chuancheng Jia,Zheng Fan,Zhaoyang Lin,Sung-Joon Lee,Timothy L. Atallah,Justin R. Caram,Yu Huang,Xiangfeng Duan

DOI: https://doi.org/10.1021/acs.nanolett.0c04594

IF: 10.8

2021-01-19

Nano Letters

Abstract:All-inorganic lead halide perovskites have attracted tremendous interest for their excellent stability when compared with hybrid perovskites. Here we report a large-area growth of monocrystalline all-inorganic perovskite thin films and further patterning them into heterostructure arrays. We show that highly oriented CsPbBr3 microcrystal domains can be readily grown on muscovite mica substrates with a well-defined epitaxial relationship, which can further expand and eventually merge into large-area monocrystalline CsPbBr3 thin films with an excellent optical quality. Taking a step further, we show the large-area CsPbBr3 thin film can be further patterned and selectively transformed into CsPbI3 using a selective anion-exchange process to produce CsPbBr3–CsPbI3 lateral heterostructure arrays with spatially modulated photoluminescence emission and an apparent current rectification behavior. The capability to grow large-area CsPbBr3 monocrystalline thin films and heterostructure arrays defines a robust material platform for both the fundamental investigations and potential applications in optoelectronics.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.nanolett.0c04594?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.nanolett.0c04594</a>.Additional figures describing the film vertical growth rate, domain flattening process, substrate guided growth of CsPbBr3 on muscovite mica and schematic energy band diagram of the heterostructure (<a class="ext-link" href="/doi/suppl/10.1021/acs.nanolett.0c04594/suppl_file/nl0c04594_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Highly Uniform Large-Area (100 cm2) Perovskite CH3NH3PbI3 Thin-Films Prepared by Single-Source Thermal Evaporation

Guangxing Liang,Huabin Lan,Ping Fan,Chunfeng Lan,Zhuanghao Zheng,Huanxin Peng,Jingting Luo

DOI: https://doi.org/10.3390/coatings8080256

IF: 3.236

2018-07-24

Coatings

Abstract:In this work, we report the reproducible preparation method of highly uniform large-area perovskite CH3NH3PbI3 thin films by scalable single-source thermal evaporation with the area of 100 cm2. The microstructural and optical properties of large-area CH3NH3PbI3 thin films were investigated. The dense, uniform, smooth, high crystallinity of large-area perovskite thin film was obtained. The element ratio of Pb/I was close to the ideal stoichiometric ratio of CH3NH3PbI3 thin film. These films show a favorable bandgap of 1.58 eV, long and balanced carrier-diffusion lengths. The CH3NH3PbI3 thin film perovskite solar cell shows a stable efficiency of 7.73% with almost no hysteresis, indicating a single-source thermal evaporation that is suitable for a large area perovskite solar cell.

materials science, multidisciplinary,physics, applied, coatings & films
Achieving Ordered and Stable Binary Metal Perovskite Via Strain Engineering

Xuxia Shai,Jinsong Wang,Pengyu Sun,Wenchao Huang,Peizhe Liao,Feng Cheng,Bowen Zhu,Sheng-Yung Chang,En-Ping Yao,Yan Shen,Ling Miao,Yang,Mingkui Wang

DOI: https://doi.org/10.1016/j.nanoen.2018.03.047

IF: 17.6

2018-01-01

Nano Energy

Abstract:Strain effects on vacancies, electronic states and stability have been disclosed for perovskite structured materials (ABX(3)) including metal oxides and organic-inorganic hybrids critical for energy storage and generation. Ion substitution has been pursued as an attractive solution to alter the crystallization or induced electronic of organic-inorganic hybrid halide lead perovskite. However, the disorganized structure of perovskite result from inappropriate substitution may cause unwanted phase transition and photo-stability. Herein, we introduce crystallization of restriction ABX(3) composition with moderate zinc (Zn) substitution to obtain the ordered and stable CH3NH3(Zn: Pb)I3-xClx crystal, which is achieved via releasing lattice strain during an appropriate lattice constriction within BX6 octahedron. We obtained an unprecedented efficiency of 20.06% under simulated sunlight with facilitating binary metal perovskite of CH3NH3(1Zn: 100Pb)I3-xClx. Our results are important to realize scale up and practical applications of efficient planar perovskite solar cells.
Growth of Compact CH3NH3PbI3 Thin Films Governed by the Crystallization in PbI2 Matrix for Efficient Planar Perovskite Solar Cells.

Junwei Chen,Zhiyang Wan,Jiandang Liu,Sheng-Quan Fu,Fapei Zhang,Shangfeng Yang,Shanwen Tao,Mingtai Wang,Chong Chen

DOI: https://doi.org/10.1021/acsami.7b18667

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:As a convenient preparation technique, a two-step method, which is normally done by spin-coating CH3NH3I onto PbI2 film followed by a thermal annealing, is generally used to prepare solution-processed CH3NH3PbI3 films for planar perovskite solar cells. Here, we prepare the compact CH3NH3PbI3 thin films by the two-step method at a low temperature (<80 °C) and investigate the effects of PbI2 crystallization on the structure-property correlation in the CH3NH3PbI3 films. It is found that the importance of the crystallization in PbI2 matrix lies in governing the transition from the (001) plane of trigonal PbI2 to the (002) plane of tetragonal CH3NH3PbI3 in the rapid reaction process for atoms to coordinate into perovskite during spin-coating, which actually determines the morphology and the type of vacancy defects in resulting perovskite; a better crystallized PbI2 film has a much stronger ability to react with CH3NH3I solution and produces larger CH3NH3PbI3 grains with a higher crystallinity. The CH3NH3PbI3/TiO2 planar solar cell derived from a better crystallized PbI2 film exhibits significantly improved performance and stability as the result of the higher crystallinity inside the perovskite film. Moreover, it is demonstrated that the crystalline PbI2 film matrix subjected to the annealing after a slow heating process prior to contacting CH3NH3I solution is more effective for CH3NH3PbI3 formation than that with a direct annealing history. The results in this paper provide a guide for preparing high-quality CH3NH3PbI3 thin films for efficient perovskite solar cells and CH3NH3PbI3 interfacial films over the layers susceptible to temperature.
Controlled Crystallization of CH3NH3PbI3 Films for Perovskite Solar Cells by Various PbI2(X) Complexes

Weifei Fu,Jielin Yan,Zhongqiang Zhang,Tao Ye,Yujing Liu,Jiake Wu,Jizhong Yao,Chang-Zhi Li,Hanying Li,Hongzheng Chen

DOI: https://doi.org/10.1016/j.solmat.2016.06.037

IF: 6.9

2016-01-01

Solar Energy Materials and Solar Cells

Abstract:Lead halide complexes are efficient precursors to obtain high quality perovskite films and high performance solar cells. However, how the lead halide complex affects the crystallization kinetics and thus the film quality of perovskite has not been systematically studied. Herein, two PbI2(X) complexes with different coordination strength of ligand X in complexation with PbI2 (PbI2(DMF) and PbI2(DMSO)) are synthesized. The correlation between the morphology, evolution of the perovskite formation, defects state, carrier lifetime and the subsequent photovoltaic performance are investigated in details via a two-step coating method with various PbI2(X) complexes. We find that PbI2(DMSO) derived perovskite film shows larger grains and vertically oriented grain boundaries as well as enhanced photoluminescence intensity and longer carrier lifetime. As a result, highly efficient inverted planar perovskite solar cells with a power conversion efficiency up to 17.0% are achieved from PbI2(DMSO) complex under 1 sun illumination. This research could open up a new pathway to further improve the performance of perovskite solar cells through the control of perovskite crystallization kinetics by choosing proper PbI2(X) complex precursors.
Preparation of CsPbBr 3 Films with Tens of Micrometer-Scale Grains and Preferential Orientation for Perovskite Solar Cells

Yukai Zhang,Fang Sheng,Hui Zhang,Xiaobing Ding,Lili Zhi,Yanqing Li,Xiaobing Cao,Xian Cui,Jinquan Wei

DOI: https://doi.org/10.1021/acsaem.3c01133

IF: 6.4

2023-12-05

ACS Applied Energy Materials

Abstract:High quality perovskite films with large grains, a preferential orientation, and a low defect density are desired for efficient perovskite solar cells. Here, we fabricate all-inorganic CsPbBr3 perovskite films from thermal vapor deposition followed by upside-down high temperature annealing. After high temperature annealing, the perovskite films with randomly oriented nanocrystals convert to continuous films with large columnar grains, (001) preferential crystal orientation, and no evident change in thickness. The average grain size reaches ∼7 μm after annealing at 375 °C for 30 min, which is almost 50 times larger than that of the primitive sample. Some large columnar grains in tens of micrometers are frequently observed under an optical microscope. The photoluminescence intensity is about 2 orders of magnitude stronger than that before annealing, showing a high-quality film with a low defect density and low nonradiative recombination. The perovskite solar cells based on the large grain films exhibit a high power conversion efficiency of 7.96%.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Investigation on Crystallization of CH3NH3PbI3 Perovskite and Its Intermediate Phase from Polar Aprotic Solvents

Yahui Li,Lili Zhi,Guixian Ge,Zhenhao Zhao,Xiaobing Cao,Feifei Chen,Feng Lin,Lijie Ci,Jialin Sun,Daming Zhuang,Jinquan Wei

DOI: https://doi.org/10.1021/acs.cgd.8b01516

IF: 4.01

2018-01-01

Crystal Growth & Design

Abstract:Perovskite films are usually fabricated by a solution-processed method due to its low cost and ease of fabrication. The organic solvent plays multiple roles in the growth of perovskites. Here, we investigate the growth of methylammonium lead iodide perovskite and its intermediate phase from microdroplets containing various solvents. The perovskite intermediate phase inclines to grow in the direction of its (020) plane from polar aprotic solvents at low temperature. At high temperature, the growth of perovskites depends on the structure of solvent molecules. The intermediate phase still grows from the solvents with a short chain structure. It tends to form smooth films containing radial domains with dimensions in tens of microns, which consist of nanocrystals due to annealing effects. However, perovskite grains grow directly from the solvents with a ring structure. It tends to form smooth thin films by joining the large hexagonal perovskite crystals together. It provides a guidance to prepare high quality perovskite films for high performance optoelectronic devices.
Preparation of CsPbBr3 Films with Tens of Micrometer-Scale Grains and Preferential Orientation for Perovskite Solar Cells

Yukai Zhang,Fang Sheng,Hui Zhang,Xiaobing Ding,Lili Zhi,Yanqing Li,Xiaobing Cao,Xian Cui,Jinquan Wei

DOI: https://doi.org/10.1021/acsaem.3c01133

IF: 6.4

2023-01-01

ACS Applied Energy Materials

Abstract:High quality perovskite films with large grains, a preferential orientation, and a low defect density are desired for efficient perovskite solar cells. Here, we fabricate all-inorganic CsPbBr3 perovskite films from thermal vapor deposition followed by upside-down high temperature annealing. After high temperature annealing, the perovskite films with randomly oriented nanocrystals convert to continuous films with large columnar grains, (001) preferential crystal orientation, and no evident change in thickness. The average grain size reaches similar to 7 mu m after annealing at 375 degrees C for 30 min, which is almost 50 times larger than that of the primitive sample. Some large columnar grains in tens of micrometers are frequently observed under an optical microscope. The photoluminescence intensity is about 2 orders of magnitude stronger than that before annealing, showing a high-quality film with a low defect density and low nonradiative recombination. The perovskite solar cells based on the large grain films exhibit a high power conversion efficiency of 7.96%
Large-Area Perovskite Nanowire Arrays Fabricated By Large-Scale Roll-To-Roll Micro-Gravure Printing And Doctor Blading

Qiao Hu,Han Wu,Jia Sun,Donghang Yan,Yongli Gao,Junliang Yang

DOI: https://doi.org/10.1039/c5nr08277c

IF: 6.7

2016-01-01

Nanoscale

Abstract:Organic-inorganic hybrid halide perovskite nanowires (PNWs) show great potential applications in electronic and optoelectronic devices such as solar cells, field-effect transistors and photodetectors. It is very meaningful to fabricate ordered, large-area PNW arrays and greatly accelerate their applications and commercialization in electronic and optoelectronic devices. Herein, highly oriented and ultra-long methylammonium lead iodide (CH3NH3PbI3) PNW array thin films were fabricated by large-scale roll-to-roll (R2R) micro-gravure printing and doctor blading in ambient environments (humility similar to 45%, temperature similar to 28 degrees C), which produced PNW lengths as long as 15 mm. Furthermore, photodetectors based on these PNWs were successfully fabricated on both silicon oxide (SiO2) and flexible polyethylene terephthalate (PET) substrates and showed moderate performance. This study provides low-cost, large-scale techniques to fabricate large-area PNW arrays with great potential applications in flexible electronic and optoelectronic devices.
An Up-Scalable Approach to CH3NH3PbI3 Compact Films for High-Performance Perovskite Solar Cells

Zhou Yang,Bing Cai,Bin Zhou,Tingting Yao,Wei Yu,Shengzhong Liu,Wen‐Hua Zhang,Can Li

DOI: https://doi.org/10.1016/j.nanoen.2015.05.027

IF: 17.6

2015-01-01

Nano Energy

Abstract:In this work, we describe an up-scalable, two step approach to prepare CH3NH3PbI3 perovskite films with high quality and exceptional uniformity at centimeter-scale (5.0 cm×5.0 cm). The resulting solar cells achieve efficiency up to 16% with an average efficiency of 14.3% for small-area devices. Remarkably, devices with size of 1.0 cm×1.0 cm made on the 5.0 cm×5.0 cm perovskite films display a very impressive efficiency up to 12.6% with an average efficiency of 10.9% (for 48 devices), which is significantly superior to previous reports (<9.0% efficiency) with centimeter-sized devices. The present approach combines the advantages of the short reaction time, facile fabrication, exceptional uniformity, good reproducibility, high device performance and up-scalability, enabling it the potential ability in large-scale photovoltaic applications.
Nanostructures: A Smooth CH3NH3PbI3 Film Via a New Approach for Forming the PbI2 Nanostructure Together with Strategically High CH3NH3I Concentration for High Efficient Planar‐Heterojunction Solar Cells (adv. Energy Mater. 23/2015)

Hong Zhang,Jian Mao,Hexiang He,Di Zhang,Hugh L. Zhu,Fengxian Xie,Kam Sing Wong,Michael Grätzel,Wallace C. H. Choy

DOI: https://doi.org/10.1002/aenm.201570124

IF: 27.8

2015-01-01

Advanced Energy Materials

Abstract:In article number 1501354, Wallace C. H. Choy and co-workers develop a new approach for forming PbI2 nanostructures together with strategically high CH3NH3I concentrations to rapidly form high quality (smooth and PbI2 residue-free) CH3NH3PbI3 perovskite films at room temperature. By employing this approach, high efficiency and stable planar-heterojunction perovskite solar cells can be fabricated.
In Situ Low-Temperature Growth and Superior Luminescent Property of Well-Aligned, High-Quality Cubic CsPbBr3 Micrometer-Scale Single Crystal Arrays on Transparent Conductive Substrates.

Sijia Li,Yongzhi She,Huaiyi Ding,Jinlong Yang,Jing Peng,Min Wu,Xiangdong Kong,Dengbao Han,Nan Pan,Xiaoping Wang

DOI: https://doi.org/10.1021/acs.jpclett.1c03984

2022-01-01

Abstract:Direct assembly of high-quality single-crystal perovskite microarrays on transparent conductive substrates and carrier injection layers is vital to realize high-performance optoelectronic devices. Although cubic-phase CsPbBr3 is considered to have a higher structural and optical quality than the orthorhombic one, obtaining a well-aligned assembly directly on the aforementioned substrates is still challenging. Here we developed a solvent-assisted crystallization strategy with the assistance of surface modifiers, through which the in situ low-temperature growth of well-aligned cubic single-crystal CsPbBr3 microarray with a preferential out-of-plane [100] orientation is achieved for the first time on commercial transparent conductive substrates. As compared with the control orthorhombic samples, the cubic CsPbBr3 single crystals possess superior properties including a higher photoluminescence internal quantum efficiency, fewer defect states, a weaker scattering by phonons, and an appearance of lasing. The results presented here can pave the way for future design and applications of optoelectronic devices based on perovskite microarrays.
Wafer-scale growth of large arrays of perovskite microplate crystals for functional electronics and optoelectronics

Gongming Wang,Dehui Li,Hung-Chieh Cheng,Yongjia Li,Chih-Yen Chen,Anxiang Yin,Zipeng Zhao,Zhaoyang Lin,Hao Wu,Qiyuan He,Mengning Ding,Yuan Liu,Yu Huang,Xiangfeng Duan

DOI: https://doi.org/10.48550/arXiv.1510.05060

2015-10-17

Materials Science

Abstract:Methylammonium lead iodide perovskite has attracted intensive interest for its diverse optoelectronic applications. However, most studies to date have been limited to bulk thin films that are difficult to implement for integrated device arrays because of their incompatibility with typical lithography processes. We report the first patterned growth of regular arrays of perovskite microplate crystals for functional electronics and optoelectronics. We show that large arrays of lead iodide microplates can be grown from an aqueous solution through a seeded growth process and can be further intercalated with methylammonium iodide to produce perovskite crystals. Structural and optical characterizations demonstrate that the resulting materials display excellent crystalline quality and optical properties. We further show that perovskite crystals can be selectively grown on prepatterned electrode arrays to create independently addressable photodetector arrays and functional field effect transistors. The ability to grow perovskite microplates and to precisely place them at specific locations offers a new material platform for the fundamental investigation of the electronic and optical properties of perovskite materials and opens a pathway for integrated electronic and optoelectronic systems.
Heteroepitaxy of Large-Area, Monocrystalline Lead Halide Perovskite Films on Gallium Arsenide

Deying Kong,Yu Zhang,Dali Cheng,Enze Wang,Kaiyuan Zhang,Huachun Wang,Kai Liu,Lan Yin,Xing Sheng

DOI: https://doi.org/10.1021/acsami.2c15243

2022-11-10

Abstract:Lead halide perovskite materials have been emerging as promising candidates for high-performance optoelectronic devices. Significant efforts have sought to realize monocrystalline perovskite films on a large scale. Here, we epitaxially grow monocrystalline methylammonium lead tribromide (MAPbBr(3)) films on lattice-matched gallium arsenide (GaAs) substrates on a centimeter scale. In particular, a solution-processed lead(II) sulfide (PbS) layer provides a lattice-matched and chemical protective...

materials science, multidisciplinary,nanoscience & nanotechnology
Enhanced Photovoltaic Performance and Thermal Stability of CH3NH3PbI3 Perovskite Through Lattice Symmetrization.

Feng Shao,Peng Qin,Dong Wang,Guoqing Zhang,Bo Wu,Jianqiao He,Wei Peng,Tze Chien Sum,Deliang Wang,Fuqiang Huang

DOI: https://doi.org/10.1021/acsami.8b17068

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:The organic-inorganic lead halide perovskites are attractive materials for photovoltaic application. The most widely studied perovskites based on methyl ammonium organic cation are less likely to form an ideal high-symmetry configuration at room temperature, leading to the appearance of local lattice strain. Herein, this study reports a strategy for the construction of thermally stable cubic perovskites at room temperature through the incorporation of the larger organic cation dimethyl ammonium. Detailed characterization on the single crystals and thin films reveals the formation of cubic phase with the addition of a certain amount of dimethyl ammonium at room temperature. With the presence of dimethyl ammonium, the nonradiative recombination in perovskite is suppressed, showing a longer PL lifetime and hole diffusion length. The more efficient charge extraction leads to an improvement in the photocurrent density, and then the device efficiency from 17.1% to 18.6%, together with an enhanced thermal stability at 85 °C. The influence of incorporating a larger organic cation on the structural configuration, optical properties, charge extraction, as well as the photovoltaic performance is systematically investigated, which offers an alternative way to improve the intrinsic stability of hybrid perovskites.
Laser-assisted Crystallization of CH3NH3PbI3 Films for Efficient Perovskite Solar Cells with a High Open-Circuit Voltage.

Faming Li,Weidong Zhu,Chunxiong Bao,Tao Yu,Yangrunqian Wang,Xiaoxin Zhou,Zhigang Zou

DOI: https://doi.org/10.1039/c6cc00753h

IF: 4.9

2016-01-01

Chemical Communications

Abstract:Laser irradiation as a rapid crystallization approach was successfully introduced to prepare homogeneous, dense-grained CH3NH3PbI3 films. Planar-heterojunction solar cells employing these high-quality films showed the optimal efficiency of 17.8% with a remarkably high open-circuit voltage of 1.146 V.

Large-scale Aligned Crystalline CH3NH3PbI3 Perovskite Array Films

Epitaxial Growth of Horizontally Aligned Single-Crystal Arrays of Perovskite

Thermally Induced Crystallization of High Quality CH3 NH3 PbI3 Film with Large Grains for Highly Efficient Perovskite Solar Cells.

Pseudohalide-Induced Recrystallization Engineering for CH3NH3PbI3 Film and Its Application in Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

Reproducible One-Step Fabrication of Compact MAPbl(3-x)Cl(x) Thin Films Derived from Mixed-Lead-Halide Precursors

Large-Area Synthesis and Patterning of All-Inorganic Lead Halide Perovskite Thin Films and Heterostructures

Highly Uniform Large-Area (100 cm2) Perovskite CH3NH3PbI3 Thin-Films Prepared by Single-Source Thermal Evaporation

Achieving Ordered and Stable Binary Metal Perovskite Via Strain Engineering

Growth of Compact CH3NH3PbI3 Thin Films Governed by the Crystallization in PbI2 Matrix for Efficient Planar Perovskite Solar Cells.

Controlled Crystallization of CH3NH3PbI3 Films for Perovskite Solar Cells by Various PbI2(X) Complexes

Preparation of CsPbBr 3 Films with Tens of Micrometer-Scale Grains and Preferential Orientation for Perovskite Solar Cells

Investigation on Crystallization of CH3NH3PbI3 Perovskite and Its Intermediate Phase from Polar Aprotic Solvents

Preparation of CsPbBr3 Films with Tens of Micrometer-Scale Grains and Preferential Orientation for Perovskite Solar Cells

Large-Area Perovskite Nanowire Arrays Fabricated By Large-Scale Roll-To-Roll Micro-Gravure Printing And Doctor Blading

An Up-Scalable Approach to CH3NH3PbI3 Compact Films for High-Performance Perovskite Solar Cells

Nanostructures: A Smooth CH3NH3PbI3 Film Via a New Approach for Forming the PbI2 Nanostructure Together with Strategically High CH3NH3I Concentration for High Efficient Planar‐Heterojunction Solar Cells (adv. Energy Mater. 23/2015)

In Situ Low-Temperature Growth and Superior Luminescent Property of Well-Aligned, High-Quality Cubic CsPbBr3 Micrometer-Scale Single Crystal Arrays on Transparent Conductive Substrates.

Wafer-scale growth of large arrays of perovskite microplate crystals for functional electronics and optoelectronics

Heteroepitaxy of Large-Area, Monocrystalline Lead Halide Perovskite Films on Gallium Arsenide

Enhanced Photovoltaic Performance and Thermal Stability of CH3NH3PbI3 Perovskite Through Lattice Symmetrization.

Laser-assisted Crystallization of CH3NH3PbI3 Films for Efficient Perovskite Solar Cells with a High Open-Circuit Voltage.