Abstract:Modern civilization and cutting-edge technologies and tools are highly dependent on energy storage devices and demand efficient and long-lasting high-energy-density storage devices. Lithium metal batteries have surpassed their competitors concerning energy density due to their inherent high specific capacity (3860 mAh/g) and the lowest electrochemical potential (-3.04 V vs. standard hydrogen electrode), proving to be one of the most favorable energy storage devices for smart and mobile gadgets, electric automobiles, grid storage, etc. However, safety-threatening and performance-decay challenges associated with lithium metal anodes, such as lithium dendrite formation, uncontrolled parasitic reactions between Li-metal and electrolyte, low coulombic efficiency, dead Li-formation, etc., restrict its employment in practical batteries. The root cause of the dendrite formation is poor Li-ion conductivity of bulk lithium metal, which results in an uneven electric field distribution, leading to non-uniform Li deposition/stripping upon repeated charge/discharge. Herein, a facile chemical reduction process is being opted to fabricate a highly Li-ion diffusive Li-Sn-based artificial SEI layer on the lithium metal surface to prevail over the above-mentioned issues. Therefore, upon careful concentration investigation of reactants, 25 mM precursor concentration (SnCl 4 in EC: DMC in 1:1 volume ration) demonstrated the best electrochemical performance, revealing a cumulative capacity of over 700 mAh/cm 2 at a current density of 1 mA/cm 2 for 1 h in a symmetric cell. Physical characterizations (XRD and SEM-EDS) showed a thin layer containing Li-Sn alloys along with LiCl formed at the lithium metal surface. Possessing high Li-ion diffusivity, Li-Sn alloyed hybrid anode illustrated a gradual decrease in the charge transfer resistance on increasing the concentration, thus, lower overpotential in symmetric cells, in contrast to pristine Li-metal. However, an increase in the electrical resistance has been observed on increasing the precursor concentration due to the presence of the insulating LiCl phase in the protective layer. Moreover, in-situ optical microscopy demonstrated more uniform and on-surface Li-deposition for the hybrid electrode, whereas mossy and dendritic growth on bare Li-metal. Full cells prepared with Li-Sn alloyed anode against NMC532 cathode illustrated stable cycling up to 150 cycles; contrastingly, the cell with pristine Li-metal showed a drastic capacity fade just after 100 cycles, demonstrating the inclination towards safer lithium metal batteries.

Intermetallic FeSn5 Phase: A New Anode Improves Lithium Ion Battery Performance

Nanospheres of a New Intermetallic FeSn5 Phase: Synthesis, Magnetic Properties and Anode Performance in Li-ion Batteries

ChemInform Abstract: Nanospheres of a New Intermetallic FeSn5 Phase: Synthesis, Magnetic Properties and Anode Performance in Li‐Ion Batteries.

A lithiation/delithiation mechanism of monodispersed MSn5 (M = Fe, Co and FeCo) nanospheres

FeSn5@Graphene Anodes for Li-Ion and Na-Ion Batteries

CoSn5 Phase: Crystal Structure Resolving and Stable High Capacity As Anodes for Li Ion Batteries.

Enhanced Electrochemical Performance of Fe0.74Sn5@Reduced Graphene Oxide Nanocomposite Anodes for Both Li-Ion and Na-Ion Batteries.

Realizing Ultrathin LiSn Alloy Anode by Tuning the Wettability of Molten Li for High-Energy-Density Batteries

Preparation of high capacity Sn2S3/Sn3S4/FeS/Fe7S8 heterostructure composite lithium-ion battery anodes from reducing agents Fe and tin-based sulfides

A New Intermetallic NiSn 5 Phase: Induced Synthesis, Crystal Structure Resolution, and Investigation of Its Mechanism.

Facile Synthesis of Fesn2 Alloy Nanoparticles As Anode Materials for Lithium-Ion Batteries

Li-Sn Alloyed Layer Containing Artificial SEI on Li-Metal Anode for Superior Lithium Metal Batteries: Development and Understanding of Anode/Electrolyte Interfacial Phenomena

Preparation and Electrochemical Performances of Nanoscale FeSn2 As Anode Material for Lithium Ion Batteries

Single-Crystal Intermetallic M-Sn (M = Fe, Cu, Co, Ni) Nanospheres As Negative Electrodes for Lithium-Ion Batteries

A Conductive Binder for High-Performance Sn Electrodes in Lithium-Ion Batteries.

Three-Dimensional Lithiophilic Li22Sn5 Alloy Skeleton for Dendrite-Free and Ultrahigh-Capacity Li Metal Anode

Anti-pulverization Intermetallic Fe–Sn Anchored on N-doped Carbon Anode Boosted Superior Power and Stable Lithium Storage

Sn-SnO2 Hybrid Nanoclusters Embedded in Carbon Nanotubes with Enhanced Electrochemical Performance for Advanced Lithium Ion Batteries

Erdite NaFeS 2 as a New Anode Material for Lithium-Ion Batteries

Sn Anodes Protected by Intermetallic FeSn2 Layers for Long‐lifespan Sodium‐ion Batteries with High Initial Coulombic Efficiency of 93.8 %

Hierarchical Sulfur-Doped Graphene Foam Embedded with Sn Nanoparticles for Superior Lithium Storage in LiFSI-Based Electrolyte