Abstract:Simultaneous excellent proton conductivity and high mechanical properties from ambient temperatures to 200 degrees C are the most pressing challenges to the long-term applications of polybenzimidazole-based proton -ex-change membranes for methanol steam reformer-proton-exchange membrane fuel cell units. Their performance is subject to the loss and plasticizing effects of free phosphoric acid (PA) during their long-term operation. Herein, novel proton carriers, termed halloysite ionogels (IL@HNTs), were prepared by filling the ionic liquid (IL) into the inorganic framework of halloysite nanotubes (HNTs) with the assistance of supercritical CO2 to replace free PA in polybenzimidazole membranes. IL@HNTs-embedded poly(2,5-benzimidazole) (ABPBI) com-posite membranes (ABPBI/IL@HNTs) were obtained by in situ synthesis and then doped with low levels of PA. Experimental characterization results showed that the ILs were confined within the lumen of the HNTs. Benefiting from the introduction of IL@HNTs, the composite membranes showed excellent proton conductivity (>10 mS/cm) from ambient temperature to 180 degrees C and a greatly enhanced mechanical strength (>75 MPa), water uptake, and PA absorbability. The ABPBI/5IL@HNTs composite membrane achieved peak power outputs of 219 and 380 mW/cm2 under anhydrous conditions at 80 and 160 degrees C, respectively, which were respectively 1.9 and 2.1 times greater than those of PA-doped ABPBI membrane. Satisfactory single-cell performance was ob-tained at a low PA doping level and without free PA. The results suggest that this approach of introducing novel ionogels to construct wide-temperature proton-exchange membranes can overcome the limitations of traditional low-temperature and high-temperature membranes, thus broadening the application temperature range of existing PEMFCs.

Protic ionic liquids: an alternative proton-conducting electrolyte for high temperature proton exchange membrane fuel cells

Polybenzimidazole/ionic-liquid-functional Silica Composite Membranes with Improved Proton Conductivity for High Temperature Proton Exchange Membrane Fuel Cells

Novel Cross-Linked Membranes Based on Polybenzimidazole and Polymeric Ionic Liquid with Improved Proton Conductivity for HT-PEMFC Applications

Cross-Linkable Polymeric Ionic Liquid Improve Phosphoric Acid Retention and Long-Term Conductivity Stability in Polybenzimidazole Based PEMs

An Imidazolium Type Ionic Liquid Functionalized Ether-Free Poly(terphenyl piperidinium) Membrane for High Temperature Polymer Electrolyte Membrane Fuel Cell Applications

Poly(fluorenyl Aryl Piperidinium) Membranes and Ionomers for Anion Exchange Membrane Fuel Cells

High conductivity poly( meta -terphenyl alkylene)s proton exchange membranes for high temperature fuel cell

Halloysite Ionogels Enabling Poly(2,5-Benzimidazole)-based Proton-Exchange Membranes for Wide-Temperature-range Applications

A CsH 2 PO 4 -Based Composite Electrolyte Membrane for Intermediate Temperature Fuel Cells

Alkali-free quaternized polybenzimidazole membranes with high phosphoric acid retention ability for high temperature proton exchange membrane fuel cells

An imidazole-philic dispersible ionic liquid provides ample proton transport channels and high proton performances for high temperature proton exchange membranes

Soluble ultra-high molecular weight poly(4,4′-diphenylether-5,5′-bibenzimidazole) based membranes with remarkable mechanical strength and specific proton conductivity for high temperature proton exchange membrane fuel cells

Novel High Temperature Proton Exchange Membranes Based on Functionalized Poly(arylene Dimethylamino Benzene) Polymers

Sulfonated poly(ether ether ketone)-Protic ionic Liquid-Based anhydrous Proton-Conducting composite polymer electrolyte membranes for High-Temperature fuel cell applications

Long side-chain N -heterocyclic cation based ionic liquid grafted poly(terphenyl piperidinium) membranes for anion exchange membrane fuel cell applications

Novel epoxy-based cross-linked polybenzimidazole for high temperature proton exchange membrane fuel cells

Highly Proton-Conductive Thermally Rearranged Polybenzoxazole for Medium-Temperature and Low-Humidity Polymer Electrolyte Fuel Cells

Proton-conductive aromatic membranes reinforced with poly(vinylidene fluoride) nanofibers for high-performance durable fuel cells

Double cross-linked 3D layered PBI proton exchange membranes for stable fuel cell performance above 200 °C

Ionic Liquid As Fuel Cell Electrolyte at Elevated Temperature

Cross-linked Aromatic Cationic Polymer Electrolytes with Enhanced Stability for High Temperature Fuel Cell Applications