Influences of Optical Feedback on the Operation of an EML Integrated with a Semiconductor Optical Amplifier

Fan Xia,Wei Hong,Junqiu Qi

DOI: https://doi.org/10.1364/acpc.2014.ath3a.5

2014-01-01

Abstract:Influences of optical feedback on the operation of monolithic integrated EML-SOA have been investigated. We found that EML-SOA shows three different operation modes for different feedback levels determined by different facet reflection and bias current.

What problem does this paper attempt to address?

External optical feedback effects on semiconductor injection laser properties

R. Lang,K. Kobayashi

DOI: https://doi.org/10.1109/jqe.1980.1070479

IF: 2.5

1980-03-01

IEEE Journal of Quantum Electronics

Abstract:Influences on the semiconductor laser properties of external optical feedback, i.e., return of a portion of the laser output from a reflector external to the laser cavity, have been examined. Experimental observations with a single mode laser is presented with analysis based on a compound cavity laser model, which has been found to explain essential features of the experimental results. In particular, it has been demonstrated that a laser with external feedback can be multistable and show hysteresis phenomena, analogous to those of non-linear Fabry-Perot resonator. It has also been shown that the dynamic properties of injection lasers are significantly affected by external feedback, depending on interference conditions between returned light and the field inside the laser diode.

engineering, electrical & electronic,optics,physics, applied,quantum science & technology
Clarifying the impact of dual optical feedback on semiconductor lasers through analysis of the effective feedback phase

Robbe de Mey,Spencer W. Jolly,Martin Virte

DOI: https://doi.org/10.1063/5.0160861

2024-04-01

Abstract:Time-delayed optical feedback is known to trigger a wide variety of complex dynamical behavior in semiconductor lasers. Adding a second optical feedback loop is naturally expected to further increase the complexity of the system and its dynamics, but due to interference between the two feedback arms, it was also quickly identified as a way to improve the laser stability. While these two aspects have already been investigated, the influence of the feedback phases, i.e., sub-wavelength changes in the mirror positions, on the laser behavior still remains to be thoroughly studied, despite indications that this parameter could have a significant impact. Here, we analyze the effect of the feedback phase on the laser stability in a dual-feedback configuration. We show an increased sensitivity of the laser system to feedback phase changes when two-feedback loops are present and clarify the interplay between the frequency shift induced by the feedback and the interferometric effect between the two feedback arms.

mathematics, applied,physics, mathematical
Influence of External Cavity Feedback on the Oscillating Characteristics of A Semiconductor Laser

Liu Chong,Ge Jian-Hong,Chen Jun

DOI: https://doi.org/10.7498/aps.55.5211

IF: 0.906

2006-01-01

Acta Physica Sinica

Abstract:Through the introduction of effective reflectivity, the influence of external optical feedback on the oscillating characteristics of a semiconductor laser is discussed, such as the threshold gain, laser frequency and output power, according to the self-consistency condition and the photon and carrier density ratio equation. In the experiment, the threshold current of a laser diode decreased from 420mA to 370mA with external cavity feedback and the slope efficiency increased. The output power obtained by theoretical simulation agrees well with the experiment results.
Electro-optic Modulator Feedback Control in Phase-Sensitive Optical Time-Domain Reflectometer Distributed Sensor.

Xiaonan Hui,Shilie Zheng,Jinhai Zhou,Chen Xu,Hao Chi,Xiaofeng Jin,Xianmin Zhang

DOI: https://doi.org/10.1364/ao.52.008581

IF: 1.9

2013-01-01

Applied Optics

Abstract:We propose a novel method to control the electro-optic modulator (EOM) applied in the phase-sensitive optical time-domain reflectometer (ϕ-OTDR) distributed sensor system, which uses the data of the OTDR curves rather than applying an independent control module. We explain the relationship between the accumulation value of the OTDR curve and the EOM's extinction ratio, and utilize this relationship to feedback control the EOM. The experimental results show that it can compensate the drift of the EOM, and make the modulator run with a high extinction ratio for a long time. And this method can also ratify a small jump of the EOM's bias point.
Influence of Residual Facet Reflection on the Eye-Diagram Performance of High-Speed Electroabsorption Modulated Lasers

Changzheng Sun,Bing Xiong,Jian Wang,Pengfei Cai,Jianming Xu,Qiwei Zhou,Yi Luo

DOI: https://doi.org/10.1109/jlt.2008.2007654

IF: 4.7

2009-01-01

Journal of Lightwave Technology

Abstract:The influence of residual facet reflection on the small-signal modulation response and the large-signal eye-diagram performance of 40 Gb/s electroabsorption modulated lasers (EMLs) is studied. Measurement and simulation show that the eye-diagram performance is not only limited by the modulation bandwidth of the device, but also significantly degraded by the low frequency resonances in the frequency response due to residual facet reflection. Clear eye-opening has been demonstrated by optimizing the anti-reflection (AR) coating of the EA modulator facet.
Theoretical Study on All-Optical Boolean Calculation Based on Nonlinear of Semiconductor Optical Amplifier

Jian‐Jun He

2007-01-01

Abstract:The semiconductor optical amplifier(SOA) is a kind of photon device which has the excellent nonlinear characteristics and has important applications for the all-optical switching,wavelength conversion,and optical logic calculations.Based on the carrier rate equation and the optical power propagation equation,numerical simulation was made on the non-linear characteristics of the SOA gain after theory analysis.Detailed study was made on the cross-gain modulation(XGM) effect——an important nonlinear characteristics of SOA under two conditions,input with a continuous and a pulse optical wave simultaneously and input with two pulse optical wave simultaneously.Theoretical study and numerical simulation show that the nonlinear characteristics based on SOA can be used to realize various all optical logic operations.
Experimental study of the influence of variable external optical feedback on visible laser diode speckle

Christopher Evered,Kang Li,Yuanlong Fan

DOI: https://doi.org/10.1364/ol.525686

IF: 3.6

2024-06-15

Optics Letters

Abstract:Christopher Evered, Kang Li, Yuanlong Fan This study employs an experimental setup with a variable feedback fraction (f_ext), external cavity length (ECL), and pump current (J) to ... [Opt. Lett. 49, 3524-3527 (2024)]

optics
Effect of external optical feedback on strongly coupled external cavity semiconductor lasers

Yanjie Chai,Hanyi Zhang,Shizhong Xie,Bingkun Zhou

1995-01-01

Tien Tzu Hsueh Pao/Acta Electronica Sinica

Abstract:Effect of external optical feedback on strongly coupled external cavity semiconductor laser is theoretically analyzed for both coherent and incoherent external optical feedback. The results show that the critical tolerable level of external optical feedback can be greatly increased by about 20dB for strongly coupled external cavity semiconductor laser compared to solitary laser diode. It is also obtained that long external cavity length and strong external cavity coupling are beneficial to resist feedback for external cavity semiconductor lasers.
Enhancement of Optical-Feedback Tolerance of SOA-Integrated EML (AXEL) by Introducing DBR-Type Laser

Mingchen Chen,Takahiko Shindo,Shigeru Kanazawa,Masahiro Nada,Yasuhiko Nakanishi,Hirotaka Nakamura

DOI: https://doi.org/10.1109/lpt.2022.3165319

IF: 2.6

2022-05-01

IEEE Photonics Technology Letters

Abstract:A DBR-laser-based SOA-assisted extended-reach EML (AXEL) was investigated in order to improve the optical feedback tolerance. The performance was tested in relative intensity noise measurement and fiber transmission experiment. A superior optical feedback tolerance was obtained in comparison with a conventional AXEL. The excess RIN induced by optical feedback is suppressed at 3-dB higher feedback power for the DBR-AXEL. 40 km fiber transmission of 10-Gbit/s signal with a feedback factor of −15 dB was achieved. The power budget was 41.3 dB. The feedback-induced power penalty was 0.52 dB.

engineering, electrical & electronic,optics,physics, applied
Simultaneous All‐optical Amplification, Inversion and Format Conversion Based on Self‐induced Nonlinear Effects in a Semiconductor Optical Amplifier

Yanqiao Xie,Ying Gao,Shiming Gao,Chester Shu

DOI: https://doi.org/10.1002/mop.26009

IF: 1.311

2011-01-01

Microwave and Optical Technology Letters

Abstract:We propose and experimentally demonstrate simultaneous all‐optical amplification, inversion and format conversion based on self‐induced nonlinear effects in a single semicondctor optcial amplifier. All these functions are verified for injected amplitude‐shift keying signals with variable extinction ratios from 5 to 12 dB. © 2011 Wiley Periodicals, Inc. Microwave Opt Technol Lett 53:1320–1323, 2011; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.26009
Feedback Effects of Mirror Loss in /spl Lambda//8 Phase-Shifted DFB-LDs

Huang, Y.,Okuda, T.,Sato, K.,Muroya, Y.

DOI: https://doi.org/10.1109/apcc.1999.820545

1999-01-01

Abstract:Feedback effects of mirror loss (FEML) in DFB-LDs were demonstrated for the first time. By changing the phase-shift in DFB-LDs, we controlled successfully the lasing wavelength deviation from the Bragg wavelength. The Bragg deviation dependence of the FEML was clarified theoretically and experimentally. The reduced relative intensity noise in /spl lambda//8 phase-shifted DFB-LDs under external optical feedback proved that negative FEML could make the DFB-LDs more stable and insensitive to external fluctuations.
Optical Feedback Characteristics in a Helium Neon Laser with a Birefringent Internal Cavity

Mao Wei,Zhang Shu-Lian,Xu Ting,Wan Xin-Jun,Liu Gang

DOI: https://doi.org/10.1088/1009-1963/16/11/045

2007-01-01

Chinese Physics

Abstract:The output characteristics of optical feedback in a helium-neon laser with a birefringent internal cavity are studied systematically in five different regions of the gain curve for the two orthogonally polarized modes. When the laser operates in the two end regions of the laser gain curve, one of the two orthogonally polarized modes will be a leading one in optical feedback. Strong mode competition can be observed. However, when the laser operates in the middle region of the laser gain curve, the two modes can oscillate equally with optical feedback. Besides the intensity of the two polarized lights, the total light intensity is also studied at the same time. M-shaped optical feedback curves are found. Particularly, when the average intensities of the two lights are comparable, the intensity modulation curve of the total light is doubled, which can be used to improve the resolution of an optical feedback system.
Influence of Facet Reflection on High-Frequency Response of Integrated Light Source and its Suppression

Peng-fei CAI,Bing XIONG,Jian WANG,Jian-bai TIAN,Chang-zheng SUN,Yi LUO

DOI: https://doi.org/10.3321/j.issn:1005-0086.2005.10.010

2005-01-01

Abstract:The influence of residual facet reflection on the high-frequency response of distributed feedback semiconductor laser(DFB-LD)/electroabsorption(EA) modulator integrated light sources and its suppression are studied.To explain the peaks observed in the low frequency range of the modulation response of the integrated light sources,we measured the relative intensity noise spectra of the DFB LD and the modulation response of the EA modulator at different reverse biases.It is found that the key factor influencing the modulation response of integrated light sources comes from the residual reflection at the EA facet rather than the microwave signal crosstalk.In order to suppress the facet reflection,improved anti-reflection coating was applied to EA modulator facet,and efficient improvement in high-frequency performance has been demonstrated.
Feedback-induced Nonlinearity and Superconducting On-Chip Quantum Optics

Zhong-Peng Liu,Hui Wang,Jing Zhang,Yu-xi Liu,Re-Bing Wu,Chun-Wen Li,Franco Nori

DOI: https://doi.org/10.1103/physreva.88.063851

IF: 2.971

2013-01-01

Physical Review A

Abstract:Quantum coherent feedback has been proven to be an efficient way to tune the dynamics of quantum optical systems and, recently, those of solid-state quantum circuits. Here, inspired by the recent progress of quantum feedback experiments, especially those in mesoscopic circuits, we prove that superconducting circuit QED systems, shunted with a coherent feedback loop, can change the dynamics of a superconducting transmission line resonator, i.e., a linear quantum cavity, and lead to strong on-chip nonlinear optical phenomena. We find that bistability can occur under the semiclassical approximation and photon antibunching can be shown in the quantum regime. Our study presents alternate perspectives for engineering nonlinear quantum dynamics on a chip.
Optical feedback signals involving the misalignment information

Gang Liu,Shulian Zhang,Ting Xu,Jun Zhu,Yan Li

DOI: https://doi.org/10.1016/j.optlaseng.2005.06.006

IF: 5.666

2006-01-01

Optics and Lasers in Engineering

Abstract:The optical feedback characteristics of the laser intensities at both emission directions are studied in a single-mode HeNe laser under low optical feedback strength. The sign inversion phenomenon can be observed when the photodetector at the main emission direction only receives the main light spot. There is no sign inversion phenomenon but intensity branch phenomena or fringe frequency-doubled phenomenon when the photodetector at the main emission direction receives both the light spots. When the optical feedback signal has intensity branch, it involves the misalignment information of the external cavity which can be used to detect the angular pitching of the reflector. The fringe frequency-doubled phenomenon can be used to double the resolution of an optical feedback system.
Research on Optical Feedback Characteristics of Frequency Modulated Microchip Nd : Yag Lasers

Yi-Dong Tan,Shu-Lian Zhang

DOI: https://doi.org/10.7498/aps.56.6408

IF: 0.906

2007-01-01

Acta Physica Sinica

Abstract:Optical feedback characteristics of frequency modulated microchip Nd: YAG lasers are investigated. Without optical feedback,the output intensity changes by one fringe with the laser frequency changing by one longitudinal mode spacing. With optical feedback, the modulation frequency of output intensity is proportional to the ratio of external cavity length to internal cavity length. The theoretical analysis based on three-cavity-mirror equivalent model is in good agreement with experimental results. The potential applications of this phenomenon in precision measurement are also discussed.
Effective Multi-section Model for Semiconductor Optical Amplifier and Applications in Optical Signal Processing

Xiang TENG,Han-yi ZHANG,Huan JIANG,Jing-sheng YANG

DOI: https://doi.org/10.3969/j.issn.1001-5868.2007.06.002

2007-01-01

Abstract:The theory of multi-section model for semiconductor optical amplifier(SOA) is described.Three multi-section models are presented and applied to the simulation of wavelength conversion based on cross-gain-modulation in SOA.By analyzing the difference between the simulated and experimental results,it is emphasized that the amplified spontaneous emission(ASE) has important effects on the gain compression and pulseshaping during the all-optical signal processing based on SOAs.
Semiconductor optical amplifier multi-wavelength fiber ring laser using frequency shifted feedback

Wang Hua,Yao Minyu,Zhang Hongming

DOI: https://doi.org/10.3969/j.issn.1005-8788.2010.01.015

2010-01-01

Abstract:A Semiconductor Optical Amplifier(SOA)-based multi-wavelength fiber ring laser using frequency shifted feedback technology is reported in this paper,in which an Acousto-Optic Modulator(AOM) is incorporated as a frequency shifter and a Mach-Zehnder(M-Z) fiber interferometer is used as a comb filter.54 50 GHz-spaced stable continuous multi-wavelength optical lasing in a range of 1.5 dB output optical spectrum and 21.7 nm bandwidth are obtained with an extinction ratio of 28 dB.This laser is characteristic of stable operation,wide output optical spectrum and low output power variations.Experimental results indicate that effective gain equalization between different lasing oscillations is achieved and the output optical spectrum bandwidth increased by 21.7% by using this technology.
Performance comparisons between semiconductor and fiber amplifier gain assistance in a recirculating frequency shifter

Xiaoxi Wang,Shayan Mookherjea

DOI: https://doi.org/10.1364/OL.43.001011

2018-03-01

Abstract:Recirculating frequency shifter (RFS) loops can be used for electronically programmable, variable-spacing multiline spectrum generation, which can benefit the development of fully flexible optical communications and other frequency comb applications. Here, we report on and explain the observation of significant performance variations between chip-based gain in semiconductor optical amplifiers (SOA) and fiber-based gain in erbium-doped fiber amplifiers (EDFA) when used as the gain element in the RFS. Previously, SOAs and EDFAs have been demonstrated in different RFS experiments and studied separately from each other; thus, discussion mainly focused on the noise from amplified spontaneous emission. We show that SOA effects, including four wave mixing, can be measured, which impose limits to the wavelength spacing of the combs, and that this effect is mitigated by increasing the RF drive frequency of the RFS and operating SOA in deeper saturation.

Influences of Optical Feedback on the Operation of an EML Integrated with a Semiconductor Optical Amplifier

External optical feedback effects on semiconductor injection laser properties

Clarifying the impact of dual optical feedback on semiconductor lasers through analysis of the effective feedback phase

Influence of External Cavity Feedback on the Oscillating Characteristics of A Semiconductor Laser

Electro-optic Modulator Feedback Control in Phase-Sensitive Optical Time-Domain Reflectometer Distributed Sensor.

Influence of Residual Facet Reflection on the Eye-Diagram Performance of High-Speed Electroabsorption Modulated Lasers

Theoretical Study on All-Optical Boolean Calculation Based on Nonlinear of Semiconductor Optical Amplifier

Experimental study of the influence of variable external optical feedback on visible laser diode speckle

Effect of external optical feedback on strongly coupled external cavity semiconductor lasers

Enhancement of Optical-Feedback Tolerance of SOA-Integrated EML (AXEL) by Introducing DBR-Type Laser

Simultaneous All‐optical Amplification, Inversion and Format Conversion Based on Self‐induced Nonlinear Effects in a Semiconductor Optical Amplifier

Feedback Effects of Mirror Loss in /spl Lambda//8 Phase-Shifted DFB-LDs

Optical Feedback Characteristics in a Helium Neon Laser with a Birefringent Internal Cavity

Influence of Facet Reflection on High-Frequency Response of Integrated Light Source and its Suppression

Feedback-induced Nonlinearity and Superconducting On-Chip Quantum Optics

Optical feedback signals involving the misalignment information

Research on Optical Feedback Characteristics of Frequency Modulated Microchip Nd : Yag Lasers

Effective Multi-section Model for Semiconductor Optical Amplifier and Applications in Optical Signal Processing

Semiconductor optical amplifier multi-wavelength fiber ring laser using frequency shifted feedback

Performance comparisons between semiconductor and fiber amplifier gain assistance in a recirculating frequency shifter