Abstract:Towards the development of a novel polishing technique for the high-precision surface finishing of miniature V-grooves, the feasibility of finishing linear V-grooves generated on an oxygen-free copper substrate using a magnetic compound fluid (MCF) slurry was experimentally investigated, and the fundamental finishing characteristics were elucidated. First, a polishing apparatus was constructed by installing an MCF unit for generating a rotary magnetic field and rotating an MCF carrier onto a polisher, along with a wave maker used for vibrating the workpiece. Then, polishing experiments were performed to clarify the fundamental polishing characteristics, including the effects of the polishing time on the material removal, the form accuracy (i.e. the form retention rate and symmetry error), and the surface roughness at different polishing locations/positions in the polishing zone. Thereafter, the fundamental characteristics were examined by investigating the distribution of abrasive particles in the polishing zone, the relative velocity of abrasive particles compared to the V-groove, and the impact angle of abrasive particles against the V-groove side surface. Finally, the effect of the MCF carrier rotation speed n(c) on the characteristics was elucidated, and an appropriate value of n(c) was proposed. The main results can be summarized as follows. (1) At the majority of locations in the polishing zone, the surface quality Ra at higher positions on the V-grooves was better than that at lower ones. At locations where abrasive particles moved from the right/left side to left/right side of the grooves, the surface quality Ra on the right/left side was better than that at the left/right side. The final surface roughness after 150 min of polishing was in the range of 15-50 nm Ra, indicating that a mirror-like surface could be successfully achieved for a miniature V-groove using the proposed technique. (2) The V-groove form accuracy, i.e. form retention rate eta and symmetry error epsilon, deteriorated during polishing, and the final form accuracy differed with the location. Nevertheless, the nand 8 values at the location where the form accuracy was the lowest were greater than 99.47% and less than 0.17, respectively. (3) Increasing the MCF carrier rotational speed n(c) deteriorated the form accuracy but improved the surface quality Ra. Taking into account the balance between the form accuracy and surface quality Ra, nc should be set at 10 rpm under the experimental conditions in the current work. (C) 2016 Elsevier Inc. All rights reserved.

Experimental Study on Lapping of Micro Groove with Controlled Force

Study on Mechanism for Material Removal and Surface Generation by Molecular Dynamics Simulation in Abrasive Processes

Design of A Micro Lapping System Based on Double-Feedback Control Algorithm for Manufacturing Optical Micro Components

A Novel Desktop Device for Lapping Milled Micro Thin-Walled Structures

A Novel Desktop Device for Lapping Thin-Walled Micro Groove

Kinematics and Trajectory Analysis of the Fixed Abrasive Lapping Process in Machining of Interdigitated Micro-Channels on Bipolar Plates

Investigation on surface evolution and subsurface damage in abrasive lapping of hard and brittle materials using a novel fixed lapping tool

Structure and Properties of Particles/rubber Composites Applied on Functionally Graded Lapping and Polishing Plate

A Study on the Material Removal Characteristics and Damage Mechanism of Lapping for Pressureless Sintered Silicon Carbide (SSiC) Microlens Cavity

Grinding and lapping induced surface integrity of silicon wafers and its effect on chemical mechanical polishing

Theoretical and experimental investigation on surface generation and subsurface damage in fixed abrasive lapping of optical glass

Theoretical and experimental investigations on conformal polishing of microstructured surfaces

Feasibility Study on Surface Finishing of Miniature V-grooves with Magnetic Compound Fluid Slurry

Experimental Study on Grinding the Micro Wall of Flexible Joints with Controllable Force

Modeling and simulation for material removal in abrasive jet precision finishing with wheel as restraint

Analysis and optimization of microchannel array precision grinding processes with micro-structured micro-grinding tool

Experimental Investigation of the Effect of Process Parameters on Material Removal Rate and Surface Finish

Bonnet Polishing of Microstructured Surface

Simulation and Experimental Study of Laser Processing NdFeB Microarray Structure

Novel functionally graded and composite-structured lapping and polishing plate for better uniformity of material removal