Abstract:An onset condition of gas entrainment (GE) due to free surface vortex has been studied to establish a design of fast breeder reactor with higher coolant velocity than conventional designs, because the GE might cause the reactor operation instability and therefore should be avoided. The onset condition of the GE has been investigated experimentally and theoretically, however, dependency of the vortex type GE on local geometry configuration of each experimental system and local velocity distribution has prevented researchers from formulating the universal onset condition of the vortex type GE. A real scale test is considered as an accurate method to evaluate the occurrence of the vortex type GE, but the real scale test is generally expensive and not useful in the design study of large and complicated FBR systems, because frequent displacement of inner equipments accompanied by the design change is difficult in the real scale test. Numerical simulation seems to be promising method as an alternative to the real scale test. In this research, to evaluate the applicability of the numerical simulation to the design work, numerical simulations were conducted on the basic experimental system of the vortex type GE. This basic experiment consisted of rectangular flow channel and two important equipments for vortex type GE in the channel, i.e. vortex generation and suction equipments. Generated vortex grew rapidly interacting with the suction flow and the grown vortex formed a free surface dent (gas core). When the tip of the gas core or the bubbles detached from the tip of the gas core reached the suction mouth, the gas was entrained to the suction tube. The results of numerical simulation under the experimental conditions were compared to the experiment in terms of velocity distributions and free surface shape. As a result, the numerical simulation showed qualitatively good agreement with experimental data. The numerical simulation results were similar to the experimental results in terms of the shape of free surface dent and the velocity distribution around the vortex, although the GE itself was not completely reproduced due to a lack of enough mesh partition. After confirming the applicability of the numerical simulation to the GE evaluation, several parameters, such as suction velocity and a configuration around suction mouth, were numerically examined to evaluate their influence on the GE. The tendencies of the GE occurrence enhanced by larger suction velocity or suction mouth on bottom surface enhance occurrence of the GE were obtained from the simulation results. These simulation results implied that the numerical simulation has enough potential to be used for the design work.

Real-Scale Numerical Simulation of Gas Entrainment Phenomena in Fast Reactor

Two-Phase Flow Simulation of Gas Entrainment Phenomena in Large-Scale Experimental Model of Sodium-Cooled Fast Reactor

S0803-1-3 Study on Evaluation of Gas Entrainment in Nuclear Reactor Vessel Using Numerical Simulation Method

Formulations and Validations of a High-Precision Volume-of-Fluid Algorithm on Nonorthogonal Meshes for Numerical Simulations of Gas Entrainment Phenomena

- 1-development and validation of high-precision cfd method with volume-tracking algorithm for gas-liquid two-phase flow simulation on unstructured mesh i 1

Formulation of High-Precision Volume-of-Fluid Method Establishing Appropriate Balance Between Pressure and Surface Tension and Its Application to Gas Entrainment Phenomena in Fast Breeder Reactors(Fast Reactor,<Special Issue>Power and Energy System Symposium)

F211 Formulation of high-precision volume-of-fluid method establishing appropriate balance between pressure and surface tension and its application to gas entrainment phenomena in fast breeder reactors

Unstructured Adaptive Mesh Technique for Gas-Liquid Two-Phase Flows

Experimental and Numerical Simulation on Sequential Three Phase Jet-Loop Reactor

Study on Applicability of Numerical Simulation to Evaluation of Gas Entrainment Due to Free Surface Vortex

Appropriate Formulations for Velocity and Pressure Calculations at Gas-liquid Interface with Collocated Variable Arrangement

High-Precision Reconstruction Of Gas-Liquid Interface In Plic-Vof Framework On Unstructured Mesh

Verification of interface-tracking method with manufactured solution

Examination of Appropriate Formulations for Velocity and Pressure Calculation Methods at Interfacial Region on Collocated Physical Variables' Distribution

Development And Verification Of Unstructured Adaptive Mesh Technique With Edge Compatibility

High-Precision Calculation of Interface Normal on Non-Orthogonal Mesh

Numerical Simulation of Cavitation by Sub-Surface Vortex (1st Report, High-Precision Numerical Simulation Scheme for Vortical Flow)

Study on Bubbly Flow Behavior in Natural Circulation Reactor by Thermal-Hydraulic Simulation Tests with SF6-Gas and Ethanol Liquid

A High‐precision Unstructured Adaptive Mesh Technique for Gas–liquid Two‐phase Flows

Numerical simulation of gas volume motion during the gas injection into liquid metal coolant

AN IMPROVED PRESSURE CALCULATION METHOD FOR SIMULATIONS OF GAS–LIQUID TWO-PHASE FLOWS ON UNSTRUCTURED MESHES