Abstract:In recent decades, geoelectrical methods have played a very important role in near-surface investigation. The most widely used of these methods is electrical resistivity tomography (ERT). Regardless of the forward and inversion algorithms used, the original data collected from a survey is the most important factor for quality of the resulted model. However, 3D electrical resistivity survey design continues to be based on data sets recorded using one or more of the standard electrode arrays. There is a recognized need for the 3D survey design to get better resolution using fewer data. Choosing suitable data from the comprehensive data set is a great approach. By reasonable selecting, better resolution can be obtained with fewer electrodes and measurements than conventional arrays. Previous research has demonstrated that the optimized survey design using the 'Compare R' method can give a nice performance.This paper adds target-oriented selection and modified the original 'Compare R' method. The survey design should be focused on specific target areas, which need a priori information about the subsurface properties. We select electrodes and configurations as the target set by the comprehensive set firstly which meets the requirements of the target area. The number of measurements and electrodes is much less than the comprehensive set and the model resolution matrix takes less time to calculate. At the next step for rank, we calculate the sensitivity matrix of the target set only once and then calculate the contribution degree of each measurement separately from it. The time of iterative calculation of the resolution matrix when measurements set changing is less than the original method.The traditional method of evaluating RMS is not appropriate for comparing the quality of collected data by different survey designs. SSIM (structural similarity index) gives more reliable measures of image similarity better than the RMS. The curves of SSIM values in three dimensions and the average SSIM are given as quantitative comparisons. Besides, the frequency of electrodes utilized given to guides on selecting the highest used electrodes. Finally, the curves of the average relative resolution S and the number of electrodes as the number of measurements increase are given, which proves the method works effectively.The results show the significance of using target-oriented optimized survey design, as it selects fewer electrodes and arrays than the original CR method. Also, it produces better resolution than conventional arrays and takes less calculation time. 3D SSIM, frequency of electrodes used, the relationship between average relative resolution, number of electrodes and number of measurements, these quantitative comparison methods can effectively evaluate the data collected in various survey designs.

Archaeological Survey under Complex Surface Conditions by Electrical Resistivity Tomography

The Study of 3-D Electrical Resistivity Tomography at an Archaeological Site

Analysis Of Integrating Ert Data Of Different Array Types: Simulation Study And Observations On An Archaeological Site

Application of Three-Dimensional Electrical Resistivity Tomography in Urban Zones by Arbitrary Electrode Distribution Survey Design

The Application of Capacitively-coupled Resistivity Method to Archaeological Exploration of Urban Site

Application of Combined Electrical Resistivity Tomography (ERT) and Seismic Refraction Tomography (SRT) Methods to Investigate Xiaoshan District Landslide Site: Hangzhou, China

Integrated Geophysical Survey for Palaeo-Drainage System at Liangzhu Sites

Strategy for Optimization of Arbitrary Electrode Distribution for 3D Electrical Resistivity Tomography in Urban Zones

Integration of 2D/3D ground penetrating radar and electrical resistivity tomography surveys as enhanced imaging of archaeological ruins: A case study in San El‐Hager (Tanis) site, northeastern Nile Delta, Egypt

Improved High-Resolution Gpr Imaging and Characterization of Prehistoric Archaeological Features by Means of Attribute Analysis

Target-oriented Optimized Survey Design and Quantitative Comparison for 3D Electrical Resistivity Tomography

Application of 3d Gpr Attribute Technology in Archaeological Investigations

High-Resolution Ground-Penetrating Radar Imaging Of Buried Culture Heritage

3D Characterization of Archaeological Remains Buried under Obstacles Using Annular Array Electric Resistivity Tomography

Integrated characterization of ancient burial mounds using ERT and limited drillings at the Hepu Han Tombs, in coastal area of Southern China

Magnetic Gradient And Ground Penetrating Radar Prospecting Of Buried Earthen Archaeological Remains At The Qocho City Site In Turpan, China

GPR Imaging and Characterization of Ancient Roman Ruins in the Aquileia Archaeological Park, NE Italy

Advances in GPR Data Acquisition and Analysis for Archaeology

3D Electrical Resistivity Tomography Using a Radial Array and Detailed Topography for Tumuli Prospection

Electrical resistivity tomography through reinforced concrete floor

Detection of shallow underground targets using electrical resistivity tomography and the implications in civil/environmental engineering