Carbon Quantum Dot Coated Mn3o4 with Enhanced Performances for Lithium-Ion Batteries

Mingjun Jing,Jufeng Wang,Hongshuai Hou,Yingchang Yang,Yan Zhang,Chengchi Pan,Jun Chen,Yirong Zhu,Xiaobo Ji

DOI: https://doi.org/10.1039/c5ta03610k

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:A C quantum dot coated Mn3O4 composite (Mn3O4/Cdots) has been obtained for the first time by a green alternating voltage electrochemical approach.

What problem does this paper attempt to address?

MnO Quantum Dots Embedded in Carbon Nanotubes As Excellent Anode for Lithium-Ion Batteries

Lijun Zhang,Guanglin Xia,Yuqin Huang,Chenyun Wei,Yiwei Yu,Dalin Sun,Xuebin Yu

DOI: https://doi.org/10.1016/j.ensm.2017.01.007

IF: 20.4

2017-01-01

Energy Storage Materials

Abstract:MnO quantum dots homogenously embedded in carbon nanotubes (denoted as MnO QDs@CNTs) were prepared via a scalable electrospinning technique with LiN3 serving as poregen agent. The strong N-2 evolution resulting from the explosive decomposition of the porogen LiN3 and oxidation diffusion of MnCl2 during the heat treatment are found to be responsible for the formation of the hierarchy structure. As binder-free anodes, the composite networks displayed extraordinary LIBs performance with good reversible capacity (as high as similar to 1100 mAh g(-1) at 100 mA g(-1)), high coulombic efficiency, outstanding rate capability and superior cyclic performance (nearly no capacity fading after 200 cycles at a high current density of 3000 mA g(-1)), owing to the unique combination of ultra-small MnO QDs and stable CNTs with excellent transport properties. This shows MnO QDs@CNTs composites are almost the most efficient MnO-based anode materials for LIBs so far.
N-Doped Graphene Quantum Dots Supported by Carbon Nanotubes Grown on Carbon Clothes for Lithium Storage

Weiwei Yao,Jing Ren,Jian Mao,Liang Wang,Zhiwen Chen,Dengyu Pan,Minghong Wu,Zhen Li

DOI: https://doi.org/10.1149/1945-7111/ab8404

IF: 3.9

2020-01-01

Journal of The Electrochemical Society

Abstract:Graphite has been widely used as an anode material for commercial lithium-ion battery applications because of its excellent stability and low cost. However, graphite-based anodes need to improve the energy storage capacities to meet the increasing power demands of next-generation technologies. Here, we have developed a class of novel and flexible electrode materials that consist of N-doped graphene quantum dots supported by carbon nanotubes grown on carbon cloth (denoted as CC/CNT@N-GQD). Such architecture synergistically combines the advantages of three dimensions/one dimension substrates and zero dimension N-GQDs. It greatly improves the electron/ion transport kinetics of N-GQDs, resulting in attractive electrochemical performance in terms of high reversible capacity and excellent rate capability. Moreover, the annealing temperature plays an important role in the control of N-doping types of CC/CNT@N-GQD. CC/CNT@N-GQD anodes annealed at 500 degrees C have a high content of pyridinic N, exhibiting a very excellent rate capability and cycling stability, as exemplified by a capacity of 2.88 mAh cm(-2) at 4 mA cm(-2) and a reversible capacity of 3.63 mAh cm(-2) after 150 cycles at 0.19 mA cm(-2). (C) 2020 The Electrochemical Society ("ECS"). Published on behalf of ECS by IOP Publishing Limited.
Sprinkling MnFe2O4 Quantum Dots on Nitrogen-Doped Graphene Sheets: the Formation Mechanism and Application for High-Performance Supercapacitor Electrodes

Lijun Su,Shulai Lei,Li Liu,Lingyang Liu,Yuefei Zhang,Siqi Shi,Xingbin Yan

DOI: https://doi.org/10.1039/c8ta02982b

IF: 11.9

2018-01-01

Journal of Materials Chemistry A

Abstract:Quantum dots (QDs)/graphene composites are interesting as promising electrode materials for high-performance supercapacitors because they can well integrate the complementary features of QDs and graphene. Herein, we demonstrate a MnFe2O4 QDs/nitrogen-doped graphene (NG) material prepared by a controllable solvothermal synthesis, in which ultra-small MnFe2O4 QDs are uniformly anchored on NG surfaces. First-principles calculations elucidate that the oxygen-containing groups of graphene oxide play a crucial role in generating such a structure, and a ferrite octahedral skeleton is firstly formed followed by Mn atom insertion. Powdery MnFe2O4 QDs/NG exhibits a high specific capacitance of 517 F g(-2) within a negative potential window (-1 approximate to 0 V) in KOH electrolyte. When the lower cut off voltage is extended to -1.2 V, the specific capacitance can be increased to 905 F g(-1). And the condensed MnFe2O4 QDs@NG electrode (forming a similar structure to pitaya slices) with an astonishing loading mass of 18 mg cm(-2) can achieve high areal and volumetric capacitances (5.3 F cm(-2) and 277.6 F cm(-3)). Moreover, carbon encapsulation is favorable for the improvement of rate and cycling performance, allowing a satisfactory capacitance of 150 F g(-1) even at 200 A g(-1) as well as a superior lifetime up to 65000 cycles. These results make such materials competitive with supercapacitor electrodes and may speed up the development of QD-based electrodes for energy storage applications.
Low-cost and Environmentally Friendly Synthesis of an Al3+and Mn4+co-doped Li4Ti5O12composite with Carbon Quantum Dots As an Anode for Lithium-Ion Batteries

Gang Wang

DOI: https://doi.org/10.1039/c9ra03897c

IF: 4.036

2019-01-01

RSC Advances

Abstract:To increase the specific capacity and conductivity of lithium titanate, low-cost and environmentally friendly carbon quantum dots (CQDs) were used to composite with Al3+and Mn4+co-doped Li4Ti5O12(LTO-Al/Mn) to improve its electrical properties.
Hierarchical MOF-derived Layered Fe3O4 QDs@C Imbedded on Graphene Sheets As a High-Performance Anode for Lithium-ion Storage

Chengxin Wang,Sadaf Mutahir,Liang Wang,Wu Lei,Xifeng Xia,Xinyan Jiao,QingLi Hao

DOI: https://doi.org/10.1016/j.apsusc.2019.144882

IF: 6.7

2020-01-01

Applied Surface Science

Abstract:Herein, a double-buffering strategy is presented to boost the lithium storage potential of Fe3O4. Firstly, the skeleton of MIL-100 (Fe) MOF is grown on graphene oxide, as a self-assembled template via in-situ solvothermal approach, which transform into ultrafine, well-dispersed and mesoporous carbon coated Fe3O4 QDs (4 nm) imbedded on reduced graphene oxide (Fe3O4 QDs@C/rG0), by pyrolysis. Each component in such a well-designed porous hierarchical structure significantly contributes to the remarkable enhancement of lithium ion storage performance, leading to high reversible capability with excellent prolonged cyclic stability after 2000 cycles (505 mAh g(-1) at 2.0 A g(-1)). Both, Graphene sheets and mesoporous carbon act as conductive support for anchoring uniform Fe3O4 QDs with confined double buffering for cyclic volume flux. Multi-channels with uniform mesopores in the self-assembled array and 4 nm QDs of Fe3O4 confined in conductive carbon shells were favorable to enhance the interfacial electron/ion transfer, leading to the excellent rate and cycling performance with released volume changes upon Li+ insertion/extraction. The present research work provides a promising outset design and synthesis strategies for metal oxide QDs based nanocomposites, which may also be extended to the other electrode material system.
Low-cost and environmentally friendly synthesis of an Al3+ and Mn4+ co-doped Li4Ti5O12 composite with carbon quantum dots as an anode for lithium-ion batteries

Hui Nan,Yiming Zhang,Haomin Wei,Huiyuan Chen,Caihong Xue,Guijun Yang,Shuai Zou,Gang Wang,Hong Lin

DOI: https://doi.org/10.1039/c9ra03897c

IF: 4.036

2019-01-01

RSC Advances

Abstract:To increase the specific capacity and conductivity of lithium titanate, low-cost and environmentally friendly carbon quantum dots (CQDs) were used to composite with Al3+ and Mn4+ co-doped Li4Ti5O12 (LTO-Al/Mn) to improve its electrical properties.
Nanoporous Composites of CoO x Quantum Dots and ZIF-Derived Carbon as High-Performance Anodes for Lithium-Ion Batteries

Dujiang Lu,Chao Yuan,Mengchun Yu,Yinghui Yang,Chao Wang,Rongzhang Guan,Xiufang Bian

DOI: https://doi.org/10.1021/acsomega.0c02037

IF: 4.1

2020-08-19

ACS Omega

Abstract:Transition-metal oxides are attracting considerable attention as anodes for lithium-ion batteries because of their high reversible capacities. However, the drastic volume change and inferior electrical conductivity greatly retard their widespread applications in lithium-ion batteries. Herein, three-dimensional nanoporous composites of CoOx (CoO and Co3O4) quantum dots and zeolitic imidazolate framework-67-derived carbon are fabricated by a precipitation method. The carbon prepared by carbonization of zeolitic imidazolate framework-67 can greatly enhance the electrical conductivity of the composite anodes. CoOx quantum dots anchored firmly on zeolitic imidazolate framework-67-derived carbon can effectively inhibit the aggregation and volume change of CoOx quantum dots during lithiation/delithiation processes. The nanoporous structure can shorten the ion diffusion paths and maintain the structural integrity upon cycling. Meanwhile, kinetics analysis reveals that a capacitance mechanism dominates the lithium storage capacity, which can greatly enhance the electrochemical performance. The composite anodes show a high discharge capacity of 1873 mAh g–1 after 200 cycles at 200 mA g–1, ultralong cycle life (1246 mAh g–1 after 900 cycles at 1000 mA g–1), and improved rate performance. This work may provide guidelines for preparing cobalt oxide-based anodes for LIBs.This article has not yet been cited by other publications.

chemistry, multidisciplinary
Na2MnPO4F/Ti3C2-CQDs Composite Cathode Material with Enhanced Electrochemical Properties for Lithium/sodium Hybrid Ion Battery

Dan Sun,Rongting Guo,Yiju Lv,Wei Li,Mingjun Lu,Qiumei Wei,Zheng Liu,Guo-Cheng Han

DOI: https://doi.org/10.1016/j.diamond.2022.109216

IF: 3.806

2022-01-01

Diamond and Related Materials

Abstract:Na2MnPO4F and Ti3C2-carbon quantum dots (CQDs) nanocomposites were prepared by wet mixing method combined with spray drying method, and the two materials were further compounded by heat treatment to get different ratios of Na2MnPO4F/Ti3C2-CQDs cathode material (NTC), the effects of Ti3C2-CQDs on the structure and electrochemical performance of the composite of Na2MnPO4F as a lithium-ion battery cathode material were investigated. The results showed that Na2MnPO4F was uniformly attached to the surface and between layers of Ti3C2-CQDs. The initial specific discharge capacity of NTC-2 at 0.1C was 67.8 mAh.g(-1), and the reversible capacity after 100 cycles was 60.7 mAh.g(-1), the capacity retention rate was as high as 90%, which all showed that Ti3C2-CQDs can enhance the cycle performance, rate performance and capacity retention rate of Na2MnPO4F. It also showed good rate performance under high current density. After the high current test, the current returned to 0.1C, and the capacity can be restored to the original value, which showed that the material has good structural stability. Therefore, Ti3C2-CQDs doped Na2MnPO4F is an important way to improve the electrochemical performance of polyanionic compounds.
Quasi-spherical N-doped Carbon aggregates embedded with massive MnO quantum dots as High-performance Anodes for Li ion batteries

Shouji Huang,Guobao Xu,Xiaolin Wei,Liwen Yang

DOI: https://doi.org/10.1016/j.scriptamat.2023.115958

IF: 6.302

2024-01-04

Scripta Materialia

Abstract:We develop a facile strategy to construct massive MnO quantum dots of average size 3 nm embedded in quasi-spherical N-doped carbon aggregates as anodes for Li ion batteries (LIBs). The unique nanostructure supplies an elastic conductive carbon frame to alleviate volume expansion, ensures almost the entire surface of each MnO particle participate in electrochemical reactions, shortens ion diffusion length, and enhances electronic conductivity. Moreover, ex-situ TEM and HRTEM findings prove excellent reversibility and stability. Therefore, nanocomposite anode shows outstanding characteristics, including a high reversible capacity with 1052 mAh g −1 at 0.3 A g −1 after 160 cycles, excellent rate capability with 407 mAh g −1 at 5 A g − 1 , and a prolonged cycling lifespan of 677 mAh g −1 at 2.0 A g −1 after 550 cycles with capacity retention of 113 %. In addition, Li full cell also show outstanding electrochemical performances by using LiFePO 4 as cathode, and employing a nanocomposite as the anode.

materials science, multidisciplinary,nanoscience & nanotechnology,metallurgy & metallurgical engineering
Enhancing the Performance of MnO by Double Carbon Modification for Advanced Lithium-Ion Battery Anodes

Xiaojian Jiang,Wei Yu,Hui Wang,Huayun Xu,Xizheng Liu,Yi Ding

DOI: https://doi.org/10.1039/c5ta06095h

IF: 11.9

2016-01-01

Journal of Materials Chemistry A

Abstract:Unique porous MnO with micro/nano-architectures has been in situ decorated with carbon layers on the surface and by carbon nanotube doping. The composites exhibit stable electrochemical performance as anodes for Li ion batteries.
Electrochemically Alternating Voltage Induced Mn3O4/Graphite Powder Composite with Enhanced Electrochemical Performances for Lithium-ion Batteries

Mingjun Jing,Hongshuai Hou,Yingchang Yang,Yan Zhang,Xuming Yang,Qiyuan Chen,Xiaobo Ji

DOI: https://doi.org/10.1016/j.electacta.2014.12.170

IF: 6.6

2015-01-01

Electrochimica Acta

Abstract:Mn3O4/graphite powder (Mn3O4/GhP) composite was successfully obtained utilizing an alternating voltage induced electrochemical method. It was found that Mn3O4 particles (∼20nm) resulted from Mn electrodes were well dispersed on the surface of GhP. The electrochemical performances of Mn3O4/GhP material as anode for lithium-ion batteries were investigated, demonstrating high specific capacity and excellent cycling stability with a high charge-discharge capacity of 1007.4 mAh g−1 after 50 cycles at a current density of 100mAg−1.
Carbon-coated manganese dioxide nanoparticles and their enhanced electrochemical properties for zinc-ion battery applications

Saiful Islam,Muhammad Hilmy Alfaruqi,Jinju Song,Sungjin Kim,Duong Tung Pham,Jeonggeun Jo,Seokhun Kim,Vinod Mathew,Joseph Paul Baboo,Zhiliang Xiu,Jaekook Kim

DOI: https://doi.org/10.1016/j.jechem.2017.04.002

IF: 13.1

2017-07-01

Journal of Energy Chemistry

Abstract:In this study, we report the cost-effective and simple synthesis of carbon-coated α-MnO2 nanoparticles (α-MnO2@C) for use as cathodes of aqueous zinc-ion batteries (ZIBs) for the first time. α-MnO2@C was prepared via a gel formation, using maleic acid (C4H4O4) as the carbon source, followed by annealing at low temperature of 270°C. A uniform carbon network among the α-MnO2 nanoparticles was observed by transmission electron microscopy. When tested in a zinc cell, the α-MnO2@C exhibited a high initial discharge capacity of 272mAh/g under 66mA/g current density compared to 213mAh/g, at the same current density, displayed by the pristine sample. Further, α-MnO2@C demonstrated superior cycleability compared to the pristine samples. This study may pave the way for the utilizing carbon-coated MnO2 electrodes for aqueous ZIB applications and thereby contribute to realizing high performance eco-friendly batteries.

chemistry, physical,engineering, chemical, applied,energy & fuels
Carbon Quantum Dot-Anchored Bismuth Oxide Composites as Potential Electrode for Lithium-Ion Battery and Supercapacitor Applications

Arul Prasath,Mattath Athika,Ezhumalai Duraisamy,Arumugam Selva Sharma,Vaithiyanathan Sankar Devi,Perumal Elumalai

DOI: https://doi.org/10.1021/acsomega.8b03490

IF: 4.1

2019-03-06

ACS Omega

Abstract:The present investigation elucidates a simple hydrothermal method for preparing nanostructured bismuth oxide (Bi2O3) and carbon quantum dot (CQD) composite using spoiled (denatured) milk-derived CQDs. The formation of the CQD-Bi2O3 composite was confirmed by UV-vis absorption, steady-state emission, and time-resolved fluorescence spectroscopy studies. The crystal structure and chemical composition of the composite were examined by X-ray diffraction, Fourier transform infrared spectroscopy, Raman spectroscopy, and thermogravimetric analysis. The surface morphology and the particle size distribution of the CQD-Bi2O3 were examined using field emission scanning electron microscope and high-resolution transmission electron microscope observations. As an anode material in lithium-ion battery, the CQD-Bi2O3 composite exhibited good electrochemical activity and delivered a discharge capacity as high as 1500 mA h g-1 at 0.2C rate. The supercapacitor properties of the CQD-Bi2O3 composite electrode revealed good reversibility and a high specific capacity of 343 C g-1 at 0.5 A g-1 in 3 M KOH. The asymmetric device constructed using the CQD-Bi2O3 and reduced graphene oxide delivered a maximum energy density of 88 Wh kg-1 at a power density of 2799 W kg-1, while the power density reached a highest value of 8400 W kg-1 at the energy density of 32 Wh kg-1. The practical viability of the fabricated device is demonstrated by glowing light-emitting diodes. It is inferred that the presence of conductive carbon network has significantly increased the conductivity of the oxide matrix, thereby reducing the interfacial resistance that resulted in excellent electrochemical performances.
Facile Ultrasonic Synthesis of CoO Quantum Dot/Graphene Nanosheet Composites with High Lithium Storage Capacity

Chengxin Peng,Bingdi Chen,Yao Qin,Shihe Yang,Chunzhong Li,Yuanhui Zuo,Siyang Liu,Jinhu Yang

DOI: https://doi.org/10.1021/nn202888d

IF: 17.1

2012-01-01

ACS Nano

Abstract:In this paper, we report a facile ultrasonic method to synthesize well-dispersed CoO quantum dots (3-8 nm) on graphene nanosheets at room temperature by employing Co-4(CO)(12) as cobalt precursor. The prepared CoO/graphene composites displayed high performance as an anode material for lithium-ion battery, such as high reversible lithium storage capacity (1592 mAh g(-1) after 50 cycles), high Coulombic efficiency (over 95%), excellent cycling stability, and high rate capability (1008 mAh g(-1) with a total retention of 77.6% after 50 cycles at a current density of 1000 mA g(-1), dramatically increased from the initial 50 mA g(-1)). The extraordinary performance arises from the structure advantages of the composites: the nanosized CoO quantum dots with high dispersity on conductive graphene substrates supply not only large quantity of accessible active sites for lithium-ion insertion but also good conductivity and short diffusion length for lithium ions, which are beneficial for high capacity and rate capability. Meanwhile, the isolated CoO quantum dots anchored tightly on the graphene nanosheets can effectively circumvent the volume expansion/contraction associated with lithium insertion/extraction during discharge/charge processes, which is good for high capacity as well as cycling stability. Moreover, regarding the anomalous behavior of capacity increase with cycles (activation effect) observed, we proposed a tentative hypothesis stressing the competition between the conductivity increase and the amorphorization of the composite electrodes during cycling in determining the trends of the capacity, in the hope to gain a fuller understanding of the inner working of the novel nanostructured electrode-based lithium-ion batteries.
Ti3C2 MXene-derived Li4Ti5O12 nanoplates with in-situ formed carbon quantum dots for metal-ion battery anodes

Yong Li,Wenhan Zhang,Chunyan Lai,Tianrang Yang,Xiwang Chang,Maohui Zhang,Liangmei Sheng,Zhiyun Yang,Daixin Ye,Kevin Huang,Jingying Xie

DOI: https://doi.org/10.1016/j.jcis.2022.09.040

IF: 9.9

2023-01-01

Journal of Colloid and Interface Science

Abstract:Two-dimensional (2D) material Ti3C2 MXenes have recently been used in electrode composites for lithium-ion batteries (LIBs) for their excellent electrical conductivity and accordion-like nanosheet morphology. However, Ti3C2 has low specific capacity and fast degradation rate upon cycling after inevitably coupling with surface species during synthesis. In this work, Ti3C2 is used as Ti-source for Li4Ti5O12 (LTO) and C-source for carbon quantum dots (CQDs) in a one-step hydrothermal process. The resultant LTO product (M-LTO) inherits the nanosheet morphology of Ti3C2 with uniformly anchored CQDs. The highly electronic conductive CQDs optimize the transmission path of ions which reduces the diffusion barrier of ions, and they further increase the density of states of the material which effectively improving the conductivity of M-LTO. Remarkable electrochemical performances including high initial specific capacity, long lifetime and excellent low temperature capacity are demonstrated for this type of electrode in LIBs, sodium ion batteries (SIBs) and lithium-magnesium ion hybrid batteries (LMIHBs). This paper offers a new strategy to the rapidly expanding research on the application of transition metal MXenes in electrodes for metal-ion batteries.

chemistry, physical
MOF-Derived Hierarchical MnO-Doped Fe3O4@C Composite Nanospheres with Enhanced Lithium Storage.

Zhishun He,Kai Wang,Shasha Zhu,Liang-ai Huang,Miaomiao Chen,Jianfeng Guo,Shien Pei,Haibo Shao,Jianming Wang

DOI: https://doi.org/10.1021/acsami.8b01358

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:Hierarchically nanostructured binary/multiple transition-metal oxides with electrically conductive coatings are very attractive for lithium-ion batteries owing to their excellent electrochemical properties induced by their unique compositions and microstructures. Herein, hierarchical MnO-doped Fe3O4@C composite nanospheres are prepared by a simple one-step annealing in Ar atmosphere, using Mn-doped Fe-based metal-organic frameworks (Mn-doped MIL-53(Fe)) as precursor. The MnO-doped Fe3O4@C composite particles have a uniform nanosphere structure with a diameter of ∼100 nm, and each nanosphere is composed of clustered primary nanoparticles with an amorphous carbon shell, forming a unique hierarchical nanoarchitecture. The as-prepared hierarchical MnO-doped Fe3O4@C composite nanospheres exhibit markedly enhanced lithium-storage performance, with a large capacity of 1297.5 mAh g-1 after 200 cycles at 200 mA g-1. The cycling performance is clarified through analyzing the galvanostatic discharge/charge voltage profiles and electrochemical impedance spectra at different cycles. The unique microstructures and Mn element doping of the hierarchical MnO-doped Fe3O4@C composite nanospheres lead to their enhanced lithium-storage performance.
Carbon Dots Supported Upon N-Doped Tio2 Nanorods Applied into Sodium and Lithium Ion Batteries

Yingchang Yang,Xiaobo Ji,Mingjun Jing,Hongshuai Hou,Yirong Zhu,Laibing Fang,Xuming Yang,Qiyuan Chen,Craig E. Banks

DOI: https://doi.org/10.1039/c4ta05611f

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:N-doped TiO2 decorated with C-dots shows superior rate capability and extended battery life when utilized in Li-ion and Na-ion batteries.
Ultra-small Co-doped Mn 3 O 4 nanoparticles tiled on multilayer graphene with enhanced performance for lithium ion battery anodes

Jun Wu

DOI: https://doi.org/10.1007/s10800-019-01358-3

IF: 2.925

2019-01-01

Journal of Applied Electrochemistry

Abstract:The synthesis of ultra-small cobalt-doped (Co-doped) Mn 3 O 4 nanoparticles tiled on multilayer graphene (MLG) surface by one-pot hydrothermal method was reported here. MLG was obtained by the ultrasonication of expanded graphite in mixture solution of N , N -Dimethylformamide (DMF) and H 2 O and used without any further treatment. Co-doped Mn 3 O 4 nanoparticles were in situ assembled onto MLG surfaces by van der Waals force between metal complex and MLG. The characterization by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy revealed that the as-prepared Co-doped Mn 3 O 4 nanoparticles were homogeneously tiled on MLG with good crystallization and uniform size. The effects of cobalt doping content on the microstructure and electrochemical performance for the composites were studied. For Co 0.45 Mn 2.55 O 4 /MLG composite, a reversible capacity of 906 mAh g −1 is stably delivered at 100 mA g −1 based on the overall weight and it is maintained to 442 mAh g −1 at a high current density of 2 A g −1 . Graphic abstract Pure and Co-doped Mn 3 O 4 nanoparticles with uniform size were synthesized to be tiled on MLG based on van der Waals force by a one-pot hydrothermal method. The effects of cobalt doping content on the microstructure and electrochemical performance of composite were studied. Co 0.45 Mn 2.55 O 4 /MLG composite exhibits a high reversible capacity, cycling stability and rate capability as anode material for lithium ion battery.
Enhanced Anode Performances Of The Fe3o4-Carbon-Rgo Three Dimensional Composite In Lithium Ion Batteries

Baojun Li,Huaqiang Cao,Jin Shao,Meizhen Qu

DOI: https://doi.org/10.1039/c1cc13462k

IF: 4.9

2011-01-01

Chemical Communications

Abstract:A three dimensional composite was constructed by anchoring Fe3O4 nanoparticles encapsulated within carbon shells onto reduced graphene oxide sheets, which exhibited enhanced anode performances in lithium ion batteries with a specific capacity of 842.7 mAh g(-1) and superior recycle stability after 100 cycles.
Co quantum dots embedded in modified montmorillonite loaded with graphitized carbon as an ultra-stable anode material for sodium-ion battery

Shiyue Cao,Xiaoting Xu,Qiming Liu,Hongyi Chen,Huijuan Zhu,Ye Lin

DOI: https://doi.org/10.1016/j.jcis.2023.07.064

IF: 9.9

2023-07-17

Journal of Colloid and Interface Science

Abstract:Carbonaceous materials are competitive anodes in sodium-ion batteries (SIBs) due to their advantages, such as low cost, abundant active sites, and porosity. However, this type of material still suffers from slow rate capability and low capacity, which greatly hinders its application. In this work, the biomass-derived carbon is optimized based on a layered montmorillonite (Mt) skeleton and the cobalt quantum dots (Co QDs). A three-dimensional (3D) combination, specifically a 3D flower-like structure, of 0D material (Co QDs) and a two-dimensional (2D) material (Mt) has been achieved. The optimization and local limited effects of the Co QDs on the electronic properties have been demonstrated by density functional theory (DFT). The metallic Co QDs and carbon could form a Mott-Schottky junction, enhancing the conductivity and Na + adsorption. Due to the synergetic improvement of structure and conductivity, the stripped Mt embedded with Co QDs loaded with nitrogen doped carbon () shows ultra-stable cycle stability (99.12% retention after 10,000 cycles at 10 A/g). This is the first time that Mt has been employed in high performance SIBs, which incubates a grand blueprint for effectively utilizing similar inactive energy-storage materials, through a simple and reliable approach.

chemistry, physical

Carbon Quantum Dot Coated Mn3o4 with Enhanced Performances for Lithium-Ion Batteries

MnO Quantum Dots Embedded in Carbon Nanotubes As Excellent Anode for Lithium-Ion Batteries

N-Doped Graphene Quantum Dots Supported by Carbon Nanotubes Grown on Carbon Clothes for Lithium Storage

Sprinkling MnFe2O4 Quantum Dots on Nitrogen-Doped Graphene Sheets: the Formation Mechanism and Application for High-Performance Supercapacitor Electrodes

Low-cost and Environmentally Friendly Synthesis of an Al3+and Mn4+co-doped Li4Ti5O12composite with Carbon Quantum Dots As an Anode for Lithium-Ion Batteries

Hierarchical MOF-derived Layered Fe3O4 QDs@C Imbedded on Graphene Sheets As a High-Performance Anode for Lithium-ion Storage

Low-cost and environmentally friendly synthesis of an Al<sup>3+</sup> and Mn<sup>4+</sup> co-doped Li<sub>4</sub>Ti<sub>5</sub>O<sub>12</sub> composite with carbon quantum dots as an anode for lithium-ion batteries

Nanoporous Composites of CoO x Quantum Dots and ZIF-Derived Carbon as High-Performance Anodes for Lithium-Ion Batteries

Na2MnPO4F/Ti3C2-CQDs Composite Cathode Material with Enhanced Electrochemical Properties for Lithium/sodium Hybrid Ion Battery

Quasi-spherical N-doped Carbon aggregates embedded with massive MnO quantum dots as High-performance Anodes for Li ion batteries

Enhancing the Performance of MnO by Double Carbon Modification for Advanced Lithium-Ion Battery Anodes

Electrochemically Alternating Voltage Induced Mn3O4/Graphite Powder Composite with Enhanced Electrochemical Performances for Lithium-ion Batteries

Carbon-coated manganese dioxide nanoparticles and their enhanced electrochemical properties for zinc-ion battery applications

Carbon Quantum Dot-Anchored Bismuth Oxide Composites as Potential Electrode for Lithium-Ion Battery and Supercapacitor Applications

Facile Ultrasonic Synthesis of CoO Quantum Dot/Graphene Nanosheet Composites with High Lithium Storage Capacity

Ti3C2 MXene-derived Li4Ti5O12 nanoplates with in-situ formed carbon quantum dots for metal-ion battery anodes

MOF-Derived Hierarchical MnO-Doped Fe3O4@C Composite Nanospheres with Enhanced Lithium Storage.

Carbon Dots Supported Upon N-Doped Tio2 Nanorods Applied into Sodium and Lithium Ion Batteries

Ultra-small Co-doped Mn 3 O 4 nanoparticles tiled on multilayer graphene with enhanced performance for lithium ion battery anodes

Enhanced Anode Performances Of The Fe3o4-Carbon-Rgo Three Dimensional Composite In Lithium Ion Batteries

Co quantum dots embedded in modified montmorillonite loaded with graphitized carbon as an ultra-stable anode material for sodium-ion battery