Effect of Cesium Chloride Modification on the Film Morphology and UV-induced Stability of Planar Perovskite Solar Cells

Wenzhe Li,Jiangwei Li,Guangda Niu,Liduo Wang

DOI: https://doi.org/10.1039/c5ta09165a

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:The interface modification of perovskite thin films has shown great potential to boost the performance of perovskite solar cells during the last few years.

What problem does this paper attempt to address?

Interface Modification with Inorganic Metal Salt for High Efficiency Perovskite Solar Cells

Yihui Zou,Liang Han,Changhong Lin,Haihua Hu,Peng Wang,Ping Lin,Lingbo Xu,Xiaoping Wu,Can Cui

DOI: https://doi.org/10.1021/acsaem.3c02723

IF: 6.4

2024-01-01

ACS Applied Energy Materials

Abstract:Interface modification has emerged as a highly effective strategy for achieving the synergistic optimization of surface defects of SnO2, film quality of perovskite, and their interfacial energy level matching, thereby contributing to the photovoltaic performance and long-term stability of perovskite solar cells (PSCs). Herein, we introduced SbCl3 into the SnO2/MAPbI(3) interface. This approach capitalizes on the difference in electronegativity and the similarity in ionic radii between Sn and Sb, inducing an interaction between Sn and O atoms on the SnO2 surface with Sb from SbCl3. The interaction results in an excellent SnO2/MAPbI(3) interface with fewer defects and better energy level alignment. Moreover, high-quality perovskite films with fewer bulk defects were achieved due to the beneficial effects of Cl- anions that passivate uncoordinated Pb2+ defects and promote MAPbI(3) crystallization. As a result, MAPbI(3) PSCs with SbCl3 modification prepared in a full open-air environment demonstrated a PCE of 20.69% along with enhanced stability. This research highlights the substantial potential of incorporating SbCl3 into the SnO2/perovskite interface as a promising approach for enhancing both the efficiency and stability of planar PSCs.
Enhanced UV-light stability of planar heterojunction perovskite solar cells with caesium bromide interface modification

wenzhe li,wei zhang,stephan van reenen,r sutton,jiandong fan,a a haghighirad,michael b johnston,liduo wang,henry j snaith

DOI: https://doi.org/10.1039/c5ee03522h

IF: 32.5

2016-01-01

Energy & Environmental Science

Abstract:Interfacial engineering has been shown to play a vital role in boosting the performance of perovskite solar cells in the past few years. Here we demonstrate that caesium bromide (CsBr), as an interfacial modifier between the electron collection layer and the CH3NH3PbI3-xClx absorber layer, can effectively enhance the stability of planar heterojunction devices under ultra violet (UV) light soaking. Additionally, the device performance is improved due to the alleviated defects at the perovskite-titania heterojunction and enhanced electron extraction.
In Situ Cesium Modification at Interface Enhances the Stability of Perovskite Solar Cells

Yao Zhao,Yicheng Zhao,Wenke Zhou,Qi Li,Rui Fu,Dapeng Yu,Qing Zhao

DOI: https://doi.org/10.1021/acsami.8b10616

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:A consensus has been reached that organic transport layer (e.g., Spiro-OMeTAD) in perovskite solar cell (PSC) is prone to be impact by mobile ions in perovskite film during long-term operation. Here, we incorporate cesium acetate as a buffer layer into perovskite solar cells to mitigate this detrimental behavior, in which cesium acetate is sandwiched between perovskite and organic transport layer. The mobile ions that migrate toward the organic transport layer (e.g., MA+) are gradually consumed by cesium acetate, resulting in cesium-rich perovskite at the interface. This in situ reaction and the subsequent Cs incorporation greatly enhance the operational stability of PSC without efficiency loss. The optimized PSC presents a power conversion efficiency of 20.9% with an open-circuit voltage of 1.18 V, maintaining ∼80% of its initial efficiency after 4500 min continuous operation at maximum power point. This new strategy opens up a new opportunity for fabricating stable perovskite solar cells.
Polymer-modified halide perovskite films for efficient and stable planar heterojunction solar cells.

Lijian Zuo,Hexia Guo,Dane W deQuilettes,Sarthak Jariwala,Nicholas De Marco,Shiqi Dong,Ryan DeBlock,David S Ginger,Bruce Dunn,Mingkui Wang,Yang Yang

DOI: https://doi.org/10.1126/sciadv.1700106

IF: 13.6

2017-01-01

Science Advances

Abstract:The solution processing of polycrystalline perovskite films introduces trap states that can adversely affect their optoelectronic properties. Motivated by the use of small-molecule surfactants to improve the optoelectronic performance of perovskites, we demonstrate the use of polymers with coordinating groups to improve the performance of solution-processed semiconductor films. The use of these polymer modifiers results in a marked change in the electronic properties of the films, as measured by both carrier dynamics and overall device performance. The devices grown with the polymer poly(4-vinylpyridine) (PVP) show significantly enhanced power conversion efficiency from 16.9 ± 0.7% to 18.8 ± 0.8% (champion efficiency, 20.2%) from a reverse scan and stabilized champion efficiency from 17.5 to 19.1% [under a bias of 0.94 V and AM (air mass) 1.5-G, 1-sun illumination over 30 min] compared to controls without any passivation. Treating the perovskite film with PVP enables a VOC of up to 1.16 V, which is among the best reported for a CH3NH3PbI3 perovskite solar cell and one of the lowest voltage deficits reported for any perovskite to date. In addition, perovskite solar cells treated with PVP show a long shelf lifetime of up to 90 days (retaining 85% of the initial efficiency) and increased by a factor of more than 20 compared to those without any polymer (degrading to 85% after ~4 days). Our work opens up a new class of chemical additives for improving perovskite performance and should pave the way toward improving perovskite solar cells for high efficiency and stability.
Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Pengyang Wang,Qi Jiang,Yang Zhao,Yong Chen,Zema Chu,Xingwang Zhang,Yuqin Zhou,Jingbi You

DOI: https://doi.org/10.1016/j.scib.2018.05.003

IF: 18.9

2018-01-01

Science Bulletin

Abstract:Perovskite crystal film quality is critical for obtaining efficient perovskite solar cells. Anti-solvent processing was used for fast crystallization of perovskite precursor film, which can form dense perovskite film. However, the crystals from this method are usually small due to the fast crystal growth process, which could lead to grain boundary recombination. Here, element chloride is introduced to enhance the perovskite layer crystallinity via slowing down the perovskite crystallization process by simultaneous introduction of methylammounium chloride (MACl) and cesium chloride (CsCl) into precursor solution. As a result, we achieve high quality of pin-hole free perovskite film with large crystal size. A power conversion efficiency of 21.55% with free of hysteresis of the device is obtained, which is among the highest efficiency of planar structure perovskite solar cells.
Applications of Cesium in the Perovskite Solar Cells

Fengjun Ye,Wenqiang Yang,Deying Luo,Rui Zhu,Qihuang Gong

DOI: https://doi.org/10.1088/1674-4926/38/1/011003

2017-01-01

Journal of Semiconductors

Abstract:Perovskite solar cells have experienced an unprecedented rapid development in the power conversion efficiency(PCE)during the past 7 years,and the record PCE has been already comparable to the traditional polycrystalline silicon solar cells.Presently,it is more urgent to address the challenge on device stability for the future commercial application.Recently,the inorganic cesium lead halide perovskite has been intensively studied as one of the alternative candidates to improve device stability through controlling the phase transition.The cesium(Cs)-doped perovskites show more superior stability comparing with organic methylammonium(MA)lead halide perovskite or formamidinium(FA)lead halide perovskite.Here,recent progress of the inorganic cesium application in organic-inorganic perovskite solar cells(PSCs)is highlighted from the viewpoints of the device efficiency and the device stability.
Enhancing perovskite solar cells efficiency through cesium fluoride mediated surface lead iodide modulation

Junming Chen,Kun Xu,Weicheng Xie,Lishuang Zheng,Yulu Tian,Jue Zhang,Jiahui Chen,Tianyuan Liu,Hanzhong Xu,Kun Cheng,Ruoming Ma,Chen Chen,Jusheng Bao,Xuchun Wang,You Liu

DOI: https://doi.org/10.1016/j.jcis.2023.08.158

2023-12-15

Abstract:The presence of an excessive amount of lead iodide on the surface of perovskite solar cells (PSCs) is a significant contributing factor that adversely affects the stability of these devices when exposed to continuous light. To address this issue, we developed an effective strategy involving polishing PbI2 on a perovskite surface using CsF. In this study, we investigated the effects of CsF post-treatment on perovskite films and their photovoltaic properties. The results of the time-resolved photoluminescence and ultraviolet photoelectron spectroscopy tests reveal the significant positive impact of our passivation method based on CsF, which reduces the valence band offset between the perovskite and hole transport layers while simultaneously enhancing the carrier interface transport. PSCs treated with CsF exhibited a photoelectric conversion efficiency (PCE) of 24.25% and an increased fill factor (FF) of 81.72%, which surpassed those of the original PSCs (PCE = 22.12% and FF = 77.40%). Furthermore, after aging for over 2500 h at room temperature and in 30 ± 10% humidity, the PCE of the unpacked PSCs reduced to only 42% of the initial value. Furthermore, the devices treated with CsF maintained their impressive performance, with the PCE maintaining optimal levels at 91% of the initial efficiency.
Interfacial Modification by Multifunctional Octocrylene for High Efficiency and Stable Planar Perovskite Solar Cells.

Yinyi Huang,Shina Li,Chaorong Wu,Shuo Wang,Chengyan Wang,RuiXin Ma

DOI: https://doi.org/10.1039/c9cc09075d

IF: 4.9

2020-01-01

Chemical Communications

Abstract:Interfacial modification of the perovskite surface with octocrylene (2-ethylhexyl-2-cyano-3,3-diphenyl-2-propenoate, OCT) is capable of enhancing humidity stability and passivating the defects of perovskite films. In this study, octocrylene can be attached to the surface of the perovskite, and the carbonyl group (C[double bond, length as m-dash]O) in octocrylene achieved excellent passivation through the Lewis base electron passivation of Pb2+ ions. By increasing the concentration of the octocrylene/IPA solution, the modified device exhibited an optimal PCE of 20.54% and a steady state output PCE of 19.75%. This study shows that the introduction of octocrylene in the preparation of perovskite could effectively enhance the performance of perovskite solar cells.
Enhanced Moisture Stability of Cesium‐Containing Compositional Perovskites by a Feasible Interfacial Engineering

Nan Li,Zonglong Zhu,Qingshun Dong,Jiangwei Li,Zhanlue Yang,Chu-Chen Chueh,Alex K. -Y. Jen,Liduo Wang

DOI: https://doi.org/10.1002/admi.201700598

IF: 5.4

2017-01-01

Advanced Materials Interfaces

Abstract:The compositional perovskites have attracted broad attention due to the improved photovoltaic performance and enhanced stability compared with the single cation perovskite, such as methylammonium lead iodide and formamidinium lead iodide. In this study, the moisture stability of the widely used cesium and bromide-containing mixed perovskites is carefully studied by characterizing the morphology, crystallization, and device performance before and after the exposure to moisture. Though the mixed perovskites possess strong resistance to moisture in the ambient air, a rapid degradation is observed when the perovskites are exposed to a high relative humidity (RH) up to 70%. The degradation is evidenced by the obvious appearance of CsPbI3 phase along with needle-like morphology after several hours' storage in 70% RH. Moreover, to suppress the erosion of perovskites by the high-level moisture, an interfacial engineering is introduced with phenylethylammonium iodide (PEAI). The PEAI passivation not only shows a retarded degradation but also delivers an enhanced photovoltaic performance from 13% to > 17% with much improved stability under high-level moisture. The results imply the efficacy of interfacial engineering in fabricating high-efficiency and stable perovskite solar cells.
Cesium-Containing Methylammonium Lead Iodide Light Absorber for Planar Perovskite Solar Cells.

Xiao-Chong Zhao,Dong-Xue Wu,Li-Jun Yang,Jun Tang,Guo-Zong Yue,Pan Yang

DOI: https://doi.org/10.1166/jnn.2020.16896

2020-01-01

Journal of Nanoscience and Nanotechnology

Abstract:Institute of Materials, Chinese Academy of Engineering Physics, Jiangyou 621908, P. R. China To improve the stability of organic-inorganic hybrid perovskite, cesium-containing methylammonium lead iodide perovskite have been synthesized by one-step solution deposition. With the increasing of Cs+ doping concentration, direct optical band gap of perovskite was increases, while defects and roughness of perovskite thin films were gradually augmented. A certain amount of Cs+ incorporated in perovskite absorb layer could improve power conversion efficiency through the enhancing of open circuit voltage and fill factor. However, excessive Cs+ doping concentration results in the reduced of short-circuit current and fill factor, which reduced power conversion efficiency. The optimized ratio 10% Cs+ doping achieved the highest power conversion efficiency (16.84%).
Interface Modification by a Multifunctional Ammonium Salt for High Performance and Stable Planar Perovskite Solar Cells

Shuo Wang,Yu Zhu,Chengyan Wang,Ruixin Ma

DOI: https://doi.org/10.1039/c9ta02631b

IF: 11.9

2019-01-01

Journal of Materials Chemistry A

Abstract:Interface modification by a multifunctional ammonium salt for high performance and stable planar perovskite solar cells.
Interfacial modification of various alkali metal cations in perovskite solar cells and their influence on photovoltaic performance

Yinyi Huang,Shina Li,Chaorong Wu,Shuo Wang,Chengyan Wang,Ruixin Ma

DOI: https://doi.org/10.1039/c9nj06342k

IF: 3.3

2020-01-01

New Journal of Chemistry

Abstract:The electron transport layer (ETL) between the perovskite material and cathode plays an important role in planar perovskite solar cells. In this study, an alkali metal salt solution was be used to modify the surface of the SnO2 electron transport layer to optimize electron transport. The I-V characteristic measurements and UV-Vis spectroscopy were used to investigate whether introducing the interface modification can increase the electron coupling and effectively extract the energy lever of electrons. The results indicated that the interfacial modification could reduce the trap density of states and increase the mobility of the SnO2 thin films. The efficient defect passivation significantly suppressed the recombination at the SnO2/perovskite interface. This method aims at passivation using simple and low-cost inorganic material poles.
Deciphering the Morphology Change and Performance Enhancement for Perovskite Solar Cells Induced by Surface Modification

Nianci Guan,Yuezhou Zhang,Wei Chen,Zhengyan Jiang,Lei Gu,Ruixue Zhu,Deependra Yadav,Deli Li,Baomin Xu,Leifeng Cao,Xingyu Gao,Yonghua Chen,Lin Song

DOI: https://doi.org/10.1002/advs.202205342

IF: 15.1

2022-12-03

Advanced Science

Abstract:A pure 2D perovskite and a 2D/3D perovskite mixture are formed on the MAPbI3 film after surface treatments. This bilayer structure gives rise to a reduced trap density and an improved energy level alignment between the perovskite and HTL. Via simulation, these two positive effects are verified to be the cause of Voc and fill factor (FF) improvement, respectively. Organic–inorganic perovskite solar cells (PSCs) have achieved great attention due to their expressive power conversion efficiency (PCE) up to 25.7%. To improve the photovoltaic performance of PSCs, interface engineering between the perovskite and hole transport layer (HTL) is a widely used strategy. Following this concept, benzyl trimethyl ammonium chlorides (BTACls) are used to modify the wet chemical processed perovskite film in this work. The BTACl‐induced low dimensional perovskite is found to have a bilayer structure, which efficiently decreases the trap density and improves the energy level alignment at the perovskite/HTL interface. As a result, the BTACl‐modified PSCs show an improved PCE compared to the control devices. From device modeling, the reduced charge carrier recombination and promoted charge carrier transfer at the perovskite/HTL interface are the cause of the open‐circuit (Voc) and fill factor (FF) improvement, respectively. This study gives a deep understanding for surface modification of perovskite films from a perspective of the morphology and the function of enhancing photovoltaic performance.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry
An Interface Co-modification Strategy for Improving the Efficiency and Stability of CsPbI 3 Perovskite Solar Cells

Hui Guan,Yutian Lei,Qiyuan Wu,Xufeng Zhou,Haoxu Wang,Gang Wang,Wenquan Li,Zhiwen Jin,Wei Lan

DOI: https://doi.org/10.1021/acsaem.2c02096

IF: 6.4

2022-10-27

ACS Applied Energy Materials

Abstract:Interface engineering is a simple and effective strategy for improving the photovoltaic performance and stability of perovskite solar cells (PSCs). Herein, an interface co-modification strategy is proposed, using [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) and 2-fluoro-1,4-phenylenediammonium iodide (2FPPD) to modify the electron transport layer (ETL)/perovskite (PVK) and the PVK/hole transport layer (HTL) interfaces, respectively. A series of characterizations demonstrate that the PCBM&2FPPD interface co-modification strategy effectively enhances the extraction and transport efficiency of carriers at the interface, passivates surface defects, inhibits the nonradiative recombination of carriers, and simultaneously inhibits ion migration. Moreover, this strategy improves the crystallinity and surface hydrophobicity of PVK and optimizes the energy level alignment of PSCs. As a result, all photovoltaic parameters are improved after optimization, where the power conversion efficiency (PCE) of PSCs has increased from 17.01% to 18.36%. Meanwhile, the optimized PSCs show excellent environmental stability, which can be stably stored in air (RH = 10–20%) for about 800 h.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Enhanced Efficiency and Environmental Stability of Planar Perovskite Solar Cells by Suppressing Photocatalytic Decomposition

Peng Zhang,Jiang Wu,Yafei Wang,Hojjatollah Sarvari,Detao Liu,Zhi David Chen,Shibin Li

DOI: https://doi.org/10.1039/c7ta04014h

IF: 11.9

2017-01-01

Journal of Materials Chemistry A

Abstract:Al-modified compact ZnO film-based planar PSCs exhibit high environmental stability and UV resistance.
Cesium Iodide Interface Modification for High Efficiency, High Stability and Low Hysteresis Perovskite Solar Cells

Fei Han,Junsheng Luo,Bowen Zhao,Zhongquan Wan,Ruilin Wang,Chunyang Jia

DOI: https://doi.org/10.1016/j.electacta.2017.03.139

IF: 6.6

2017-01-01

Electrochimica Acta

Abstract:Each interface is crucial to perovskite solar cells (PSCs), so the interface modification is often used to improve the PV performances. In this manuscript, an environment-friendly cesium iodide (CsI) interface layer between the mesoporous TiO2 (mp-TiO2) and the MAPbI(3) perovskite active layer was introduced to improve the PV performances and stabilities of PSCs and significantly reduce hysteresis of the device. After optimizing, the PSC employing a CsI-modified mp-TiO2 as electron transporting layer (ETL) could obtain a high fill factor (FF) of 0.79 with an increased power conversion efficiency (PCE) of 17.10% and a low hysteresis index (HI) of 0.10 under illumination of AM 1.5G, while FF of 0.75 and PCE of 14.38% for PSC without CsI interface modification. The enhanced PV performances can be attributed to the improved surface morphology of mp-TiO2, the lower work function (WF) of TiO2, the passivation of surface trap states, the improved perovskite crystallization and reduced grain boundaries. Besides, the reduced WF of TiO2 results in the enhanced built-in potential, which promotes the charge separation, transport and collection. (C) 2017 Elsevier Ltd. All rights reserved.
Vertically-aligned quasi-2D cesium lead halide perovskite solar cells

Xuanling Liu,Meiqian Tai,Jingkun Gu,Ziyi Wu,Han Zhong,Xuanyu Wang,Zhiping Wang,Hong Lin

DOI: https://doi.org/10.1039/d2tc01442d

IF: 6.4

2022-01-01

Journal of Materials Chemistry C

Abstract:Quasi-2D cesium lead halide perovskites exhibit better stability than 3D CsPbI3 due to the steric hindrance, decreased surface energy, and improved hydrophobicity brought by long-chain organic spacers, such as phenylethylammonium (PEA) cations. However, crystal-orientation-induced poor charge transport and phase impurities greatly limit their performance. Here, we report effective approaches to tuning the crystal orientation of quasi-2D crystalline films in inorganic cesium lead halide perovskites. By reducing the N,N-dimethylformamide/dimethyl sulfoxide ratio and introducing MACl in the precursor solutions, we are able to achieve vertically-aligned PEA(2)Cs(3)Pb(4)I(13) perovskite films with enhanced film coverage, decreased trap density, and improved phase purity. The optimized solar cell devices show over 70% improvement in photocurrent which results in a 30% enhancement in efficiency. The unencapsulated cesium-based 2D device preserved 70% of its initial efficiency after being exposed to humid air for 30 days.
Manipulating Nucleation and Crystal Growth of Inorganic Perovskite Solar Cells

Xinwen Zhang,Chengbin Fei,Lening Shen,Pramod Baral,Sankaranarayanan Nair Vijayaraghavan,Feng Yan,Xiong Gong,He Wang

DOI: https://doi.org/10.1021/acsami.3c08746

IF: 9.5

2023-08-08

ACS Applied Materials & Interfaces

Abstract:Inorganic metal halide perovskite materials as sunlight absorbers for solar cells exhibit better thermal stability than organic-inorganic hybrid counterparts. Pure cesium lead triiodide (CsPbI(3)), with the most suitable band gap, suffers phase instability under an ambient environment. Nucleation and crystal growth are two crucial steps in fabricating a solution-processed perovskite film. A high-quality perovskite film with good morphology makes a significant impact on the efficiency and...

materials science, multidisciplinary,nanoscience & nanotechnology
Surface Modulation of Halide Perovskite Films for Efficient and Stable Solar Cells

Qinxuan Dai,Chao Luo,Xianjin Wang,Feng Gao,Xiaole Jiang,Qing Zhao

DOI: https://doi.org/10.1088/1674-1056/ac1fe0

2022-01-01

Abstract:As the main distribution place of deep-level defects and the entrance of water, the interface is critical to determining both the power conversion efficiency (PCE) and the stability of perovskite solar cells (PSCs). Suitable interface design can dramatically passivate interface defects and optimize energy level alignment for suppressing the nonradiative recombination and effectively extracting the photogenerated carriers towards higher PCE. Meanwhile, a proper interface design can also block the interface diffusion of ions for high operational stability. Therefore, interface modification is of great significance to make the PSCs more efficient and stable. Upon optimized material choices, the three-dimensional halide perovskite graded junction layer, low-dimensional halide perovskite interface layer and organic salt passivation layer have been constructed on perovskite films for superior PSCs, yet a systematic review of them is missing. Thus, a guide and summary of recent advances in modulating the perovskite films interface is necessary for the further development of more efficient interface modification.
An Effective Modulation of Bulk Perovskite by V2CTx Nanosheets for Efficient Planar Perovskite Solar Cells

Chen Tian,Yajie Yan,Shanglei Feng,Jiaou Wang,Yingchun Niu,Xiaoxi Li,Huanxin Ju,Quan Xu,Yang Huang,Hua Dong,Ziqi Liang,Bitao Dong,Lina Li,Yingguo Yang

DOI: https://doi.org/10.1039/d2ta05836g

IF: 11.9

2023-01-01

Journal of Materials Chemistry A

Abstract:Crystallization modulation and defect passivation are key for high performance perovskite solar cells (PSCs) through suppressing defects in the surface and/or near the grain boundaries (GBs) of solution-processed perovskite films.

Effect of Cesium Chloride Modification on the Film Morphology and UV-induced Stability of Planar Perovskite Solar Cells

Interface Modification with Inorganic Metal Salt for High Efficiency Perovskite Solar Cells

Enhanced UV-light stability of planar heterojunction perovskite solar cells with caesium bromide interface modification

In Situ Cesium Modification at Interface Enhances the Stability of Perovskite Solar Cells

Polymer-modified halide perovskite films for efficient and stable planar heterojunction solar cells.

Synergistic Improvement of Perovskite Film Quality for Efficient Solar Cells Via Multiple Chloride Salt Additives

Applications of Cesium in the Perovskite Solar Cells

Enhancing perovskite solar cells efficiency through cesium fluoride mediated surface lead iodide modulation

Interfacial Modification by Multifunctional Octocrylene for High Efficiency and Stable Planar Perovskite Solar Cells.

Enhanced Moisture Stability of Cesium‐Containing Compositional Perovskites by a Feasible Interfacial Engineering

Cesium-Containing Methylammonium Lead Iodide Light Absorber for Planar Perovskite Solar Cells.

Interface Modification by a Multifunctional Ammonium Salt for High Performance and Stable Planar Perovskite Solar Cells

Interfacial modification of various alkali metal cations in perovskite solar cells and their influence on photovoltaic performance

Deciphering the Morphology Change and Performance Enhancement for Perovskite Solar Cells Induced by Surface Modification

An Interface Co-modification Strategy for Improving the Efficiency and Stability of CsPbI 3 Perovskite Solar Cells

Enhanced Efficiency and Environmental Stability of Planar Perovskite Solar Cells by Suppressing Photocatalytic Decomposition

Cesium Iodide Interface Modification for High Efficiency, High Stability and Low Hysteresis Perovskite Solar Cells

Vertically-aligned quasi-2D cesium lead halide perovskite solar cells

Manipulating Nucleation and Crystal Growth of Inorganic Perovskite Solar Cells

Surface Modulation of Halide Perovskite Films for Efficient and Stable Solar Cells

An Effective Modulation of Bulk Perovskite by V2CTx Nanosheets for Efficient Planar Perovskite Solar Cells