An Adaptive Alarm Method for Tool Condition Monitoring Based on Probability Density Functions Estimated with the Parzen Window

Xiaoguang Chen,Guanghua Xu,Fei Liu,Xiang Wan,Qing Zhang,Sicong Zhang

DOI: https://doi.org/10.1007/978-3-319-09507-3_1

2015-01-01

Abstract:Tool condition monitoring plays an important role in modern automatic processing for ensuring the processing quality and the machine life [1].

What problem does this paper attempt to address?

A Self-Adaptive Alarm Method for Tool Condition Monitoring Based on Parzen Window Estimation

Xiaoguang Chen,Guanghua Xu

2013-01-01

Journal of Vibroengineering

Abstract:Tool condition monitoring (TCM) takes an important position in CNC manufacturing processes, especially in damages avoiding of working parts and CNC itself. This paper presents a self-adaptive alarm method using probability density functions estimated with the Parzen window based on current signals, which gives an adaptively and rapidly corresponding alarm when the cutting tool fracture occurs. A CNC with cutting tools was obtained by Guangzhou CNC Company for test purpose, and the relative experiments were done in the state key laboratory. Current signals of the spindle motor and the main feed motor were acquired during the tool life. A probability model estimated with the Parzen window is established for current data fusion to alarm adaptively. At the meantime, the acoustic emission (AE) signals were acquired for comparison purpose. Experimental results show that this technique is flexible and fast enough to be implemented in real time for online tool condition monitoring.
Comprehensive alarm method for equipment conditions based on parzen window estimation

Han LIU,Qing ZHANG,Li-hua MENG,Kai YANG,Guang-hua XU

DOI: https://doi.org/10.3969/j.issn.1000-3835.2013.03.022

2013-01-01

Abstract:To improve the adaptability of traditional monitoring and alarming methods and fuse multiple monitoring parameters, a comprehensive alarm method for condition monitoring based on Parzen window estimation was proposed. The joint probability density function of multiple monitoring parameters was estimated to describe the distribution of monitoring data. The alarm boundary was set with Parzen window function of monitoring data located in the marginal distribution area. Along with accumulation of monitoring data, the alarm boundary was continuously adjusted to accommodate new operation performance. The proposed method was evaluated with monitoring data measured on rotor test rig and heating furnace fan. Results showed that faults under different running conditions are well identified.
On-line tool condition monitoring based on intelligent-alarm

Guanghua Xu,Lihua Meng,Kuosheng Jiang,Sicong Zhang,Ailing Luo

2013-01-01

Abstract:In order to improve the ability of tool wear monitoring in the machining process, the spindle current and feed current are selected as the main information. The multi-feature extraction of current signal is based on the wavelet decomposition and soft-sensing model. The information of tool wear and break can be reflected from the processing of feed and spindle driving. On the basis of above all, the data fusion of the multi-feature information and the construction of intelligent alarm model can be implemented based on Parzen windows. The alarm boundary is determined based on PaTa criterion, so the intelligent alarm of tool condition can be achieved. When applying this technology to tool machining, it is shown from the experiment results that this technology can monitor tool condition in real-time and alarm in time.
Adaptive Alarm Technology of Tool Breakage Based on Wavelet Packet and Probabilistic Neural Network

Jiang Kuosheng,Xu Guanghua,Tao Tangfei,Meng Lihua,Wei Fugui

2011-01-01

Abstract:The current methods for condition monitoring of cutting tool was based on static alarm. To solve the current problem, the paper proposed a method of determining the dynamic alarm line for cutting tool condition monitoring. This method used the wavelet packet analysis to extract the eigenvectors of cutting tool wear condition, and used the probabilistic neural network to build the model of cutting tool running condition.The alarm value was determined and the alarm line was settled on the foundation of history data, thus the alarm line of tool wear monitoring can be adaptively adjusted to the actual operation of machine. The result shows that the method established the relevance between tool life and the actual running of machine and provids a new way to monitor the cutting tool wear. The method is of important theoretical significance and good application value.
Monitoring of Dynamic Process Using Hierarchical Probability Density Decomposition

Anni Ying,Shihua Luo,Jiusun Zeng,Lei Xie,Uwe Kruger

DOI: https://doi.org/10.1109/cac.2017.8243627

2017-01-01

Abstract:Monitoring of dynamic industrial process has been increasingly important due to more and more strict safety and reliability requirements. Popular methods like time lagged arrangement-based and subspace-based approaches exhibit good performance in fault detection, however, they suffer from difficulty in accurately isolating faulty variables and diagnosing fault types. To alleviate this difficulty, this article considers a state space model whose joint probability is decomposed hierarchically into the multiplication of several conditional densities and a low dimensional density. Two nonparametric kernel density estimation methods are used to estimate these decomposed densities. By analyzing which density exceeds the confidence limit, information on faulty variables and fault types can be obtained. Application study to simulation examples show that the proposed method is more efficient in isolating and diagnosing process fault than competitive methods.
A flexible principle component analysis method for process monitoring

Mao Zhenhua,Zhao Yuhong,Zhou Lifang

DOI: https://doi.org/10.1109/ICNC.2008.750

2008-01-01

Abstract:A flexible principle component analysis method for adaptive process monitoring based on moving window principle component analysis is presented to make a compromise between the sensitivity to fault detection and the robustness to process changes. A flexibility factor is introduced in the new method to put more emphasis on more recent data in the moving window. The feasibility and advantages of the proposed method is illustrated by application on data from Tennessee Eastman process simulation anda real industrial process respectively. © 2008 IEEE.
Process monitoring based on factor analysis: Probabilistic analysis of monitoring statistics in presence of both complete and incomplete measurements

Zhonggai Zhao,Qinghua Li,Biao Huang,Fei Liu,Zhiqiang Ge

DOI: https://doi.org/10.1016/j.chemolab.2014.12.010

IF: 4.175

2015-01-01

Chemometrics and Intelligent Laboratory Systems

Abstract:In generic process monitoring approaches based on probabilistic latent variable models, such as probabilistic principal component analysis (PPCA) or factor analysis (FA) model, the online score and residual are characterized by probability distributions. However, only their expectations are involved in the calculations of monitoring statistics, square prediction error (SPE) and Hotelling T2, which ignore the information of their variances and may result in missed fault alarms. Based on the FA model, this paper investigates the probabilistic uncertainties of monitoring statistics arising from both inherent nature and missing measurements of the process data. The proposed method derives the distributions of both the online factor and residual at each sampling instant, and then transforms generic monitoring statistics into general quadratic forms. As a result, novel monitoring statistics are developed based on the probabilistic uncertainties of the generic statistics. In addition, the proposed monitoring statistics are extended to the case of incomplete measurements, in which the conditional distributions of the online measurement, factor and residual are computed and used to construct the statistics for process monitoring. Simulation examples illustrate the feasibility of the proposed method and demonstrate its effectiveness.
On-line tool wear monitoring under variable milling conditions based on a condition-adaptive hidden semi-Markov model (CAHSMM)

Shichao Yan,Liang Sui,Siqi Wang,Yuwen Sun

DOI: https://doi.org/10.1016/j.ymssp.2023.110644

IF: 8.4

2023-10-01

Mechanical Systems and Signal Processing

Abstract:Since tool wear during machining process imposes a significant limitation on production quality as well as efficiency, on-line tool wear monitoring (TWM) is one of considerably crucial issues for intelligent manufacturing system. However, there is still a lack of universal on-line TWM techniques appropriate for the practical production process with variable machining parameters. Therefore, this study proposes a highly condition-adaptive method for tool wear state monitoring and remaining useful life (RUL) estimation under time-varying operation conditions. Multi-domain features are first extracted from vibration, acoustic emission and sound signals, and subsequently fused by the kernel principal component analysis (KPCA) to highlight discriminative information correlated to tool wear. A condition-adaptive hidden semi-Markov model (CAHSMM) is established to describe the evolution of tool wear, in which the accelerated failure time model (AFTM) embedded with Taylor tool life equation is utilized to determine the state transition probabilities that are strongly dependent on cutting parameters and duration time. Moreover, to extrapolate the Gaussian mixture models (GMMs) used to represent the observation probability beyond the range where they were trained, a Moment matching based on-line unsupervised transfer learning (OUTL) method is developed. After obtaining the state transition and observation probabilities, a modified forward algorithm is eventually implemented so as to assess tool wear online. Both the dataset from milling experiments of Ti6Al4V and PHM 2010 are employed for verifying the effectiveness of the proposed method. The results show that the presented method enables to reliably evaluate wear state and RUL of the cutter even under time-switching operation parameters, which demonstrates its promising potential for industrial applications.

engineering, mechanical
A condition monitoring approach for machining process based on control chart pattern recognition with dynamically-sized observation windows

Zhiyuan Lu,Meiqing Wang,Wei Dai

DOI: https://doi.org/10.1016/j.cie.2020.106360

2020-04-01

Abstract:<p>In the manufacturing of metallic parts, the machining process is a critical factor for ensuring product quality. Machining condition monitoring is essential for the intelligent process. Existing machining condition monitoring approaches usually detect abnormal conditions for a fixed machining procedure, which is unrealistic and impractical for real practical applications. In this paper, a novel generalized machining condition monitoring approach based on control chart pattern recognition (CCPR) with dynamically-sized observation windows for online data is proposed. More precisely, two critical issues are addressed. First, the development of a CCPR model that handles patterns with stochastic sample size. Second, a procedure for selecting the window size for detecting abnormal machining conditions. An information fusion framework is implemented to assist the machining conditions monitoring by combining data from multiple sensors and multiple sized observation windows. Experiments are conducted to validate the feasibility of the proposed approach for two machining processes with the different cutting parameters. The results demonstrate the applicability of the proposed approach for conducting condition monitoring for machining process under different machining environments as needed in practice.</p>

computer science, interdisciplinary applications,engineering, industrial
On-line Monitoring for Cutting Tool Wear Reliability Analysis

Feng Ding,Lijuan Zhang,Zhengjia He

DOI: https://doi.org/10.1109/wcica.2011.5970535

2011-01-01

Abstract:Aiming at operational reliability analysis and assessment based on condition monitoring information in this paper, a methodology of reliability modeling and assessment based on cutting tool vibration signal feature extraction using proportional hazards model is proposed. Root Mean Square and Peak of time domain index from vibration signals, which are closely related to tool wear degradation states, are selected as covariates introduced to proportional hazards model for the tool wear reliability analysis. The proposed approach shows a considerable advantage of establishing significant association relationship between the tool condition monitoring information and the life distribution of tool wear. It is appropriate to provide individual cutting tool operational reliability assessment effectively. The experimental study on the CNC lathe turning process is given to validate the effectiveness of the proposed method. The results have shown that the approach are promising and give good estimation ability of reliability for tool wear degradation states.
A Hybrid-Driven Probabilistic State Space Model for Tool Wear Monitoring

Zhipeng Ma,Ming Zhao,Xuebin Dai,Yang Chen

DOI: https://doi.org/10.1016/j.ymssp.2023.110599

IF: 8.4

2023-01-01

Mechanical Systems and Signal Processing

Abstract:Tool wear monitoring (TWM) is essential to improve product quality and maintain machining safety. Within recent years, numerous techniques have been developed for TWM, including data-driven methods and physics-based models. However, traditional data-driven methods are highly dependent on measured data. The physics-based models are difficult to model complex machining processes. To solve these problems, a hybrid-driven probabilistic state space model is proposed to improve the accuracy and robustness of TWM. In this work, a sensitive feature extraction scheme is first constructed to eliminate interferences and redundancies for improving monitoring efficiency. Subsequently, the Gaussian process is innovatively developed to integrate the data mining and physical model from a probabilistic perspective. On this basis, the particle filter is then utilized to estimate the model parameters and estimate tool wear conditions. Finally, an adaptive wear state recognition method is further established for the predictive maintenance of cutting tools. The practical data obtained from milling experiments are used to validate the effectiveness of the proposed methodology. The results show that the proposed hybrid-driven method effectively improves tool wear prediction accuracy to over 97.7%, while the constructed probabilistic model successfully evaluates the prediction results with over 95% confidence. Therefore, the developed methodology may provide a promising way for tool health management to improve economic efficiency and maintain machining safety.
In-situ tool wear condition monitoring during the end milling process based on dynamic mode and abnormal evaluation

Min Chen,Jianwei Mao,Yu Fu,Xin Liu,Yuqing Zhou,Weifang Sun

DOI: https://doi.org/10.1038/s41598-024-63865-4

IF: 4.6

2024-06-07

Scientific Reports

Abstract:Rapid tool wear conditions during the manufacturing process are crucial for the enhancement of product quality. As an extension of our recent works, in this research, a generic in-situ tool wear condition monitoring during the end milling process based on dynamic mode and abnormal evaluation is proposed. With the engagement of dynamic mode decomposition, the real-time response of the sensing physical quantity during the end milling process can be predicted. Besides, by constructing the graph structure of the time series and calculating the difference between the predicted signal and the real-time signal, the anomaly can be acquired. Meanwhile, the tool wear state during the end milling process can be successfully evaluated. The proposed method is validated in milling tool wear experiments and received positive results (the mean relative error is recorded as 0.0507). The research, therefore, paves a new way to realize the in-situ tool wear condition monitoring.

multidisciplinary sciences
Real-time Tool Breakage Monitoring Based on Dimensionless Indicators under Time-Varying Cutting Conditions

Lele Bai,Hongguang Liu,Jun Zhang,Wanhua Zhao

DOI: https://doi.org/10.1016/j.rcim.2022.102502

IF: 10.103

2022-01-01

Robotics and Computer-Integrated Manufacturing

Abstract:Tool breakage occurs randomly during machining operations, which induces more severe impacts on the quality of components compared to progressive tool wear. It is widely acknowledged that the unpredictable changes in cutting conditions will cause fluctuations in the signal amplitude and thus generate false alarms. This study introduced a novel method for tool breakage monitoring based on dimensionless indicators under time-varying cutting conditions. The amplitude ratio (AR) and the energy ratio (ER) were proposed according to the power spectrum of the spindle vibration signal, which represents the change of amplitude and the energy distribution, respectively. The AR and ER are normalized and integrated into a unified indicator for real-time breakage monitoring. The floating monitoring threshold is designed based on the Gaussian distribution. Moreover, the material removal rate (MRR) is selected as a secondary indicator to accurately identify tool breakage based on determining the amplitude fluctuation caused by cutting conditions or teeth breakage. The effectiveness of the proposed method for tool breakage monitoring has been verified under the constant, time-varying, and entry/ exit cutting conditions. The results show that the proposed indicators have higher sensitivity than the traditional root mean square (RMS) features and eliminate false alarms during condition change transients. This research provides a potential solution for tool breakage monitoring under complex cutting conditions.
Dynamic probabilistic predictable feature analysis for multivariate temporal process monitoring

Wei Fan,Qinqin Zhu,Shaojun Ren,Liang Zhang,Fengqi Si

DOI: https://doi.org/10.48550/arXiv.2109.14666

2022-11-09

Abstract:Dynamic statistical process monitoring methods have been widely studied and applied in modern industrial processes. These methods aim to extract the most predictable temporal information and develop the corresponding dynamic monitoring schemes. However, measurement noise is widespread in real-world industrial processes, and ignoring its effect will lead to sub-optimal modeling and monitoring performance. In this article, a probabilistic predictable feature analysis (PPFA) is proposed for multivariate time series modeling, and a multi-step dynamic predictive monitoring scheme is developed. The model parameters are estimated with an efficient expectation-maximum algorithm, where the genetic algorithm and Kalman filter are designed and incorporated. Further, a novel dynamic statistical monitoring index, Dynamic Index, is proposed as an important supplement of $\text{T}^2$ and $\text{SPE}$ to detect dynamic anomalies. The effectiveness of the proposed algorithm is demonstrated via its application on the three-phase flow facility and a medium speed coal mill.

Methodology,Signal Processing
Tool Condition Monitoring with Sparse Decomposition

Kunpeng Zhu

DOI: https://doi.org/10.1007/978-3-030-87878-8_7

2021-01-01

Abstract:In modern CNC machining, an effective tool condition monitoring (TCM) system can improve productivity, ensure workpiece quality and enhance the manufacturing intelligence (Dornfeld and Lee in Precision manufacturing. Springer, 2007; Teti et al., CIRP Annals-Manuf Tech 59:717–739, 2010). Due to its importance, tool condition monitoring (TCM) has been extensively studied (Teti et al., in CIRP Annals-Manuf Tech 59:717–739, 2010). The earlier study on TCM is mainly carried out with time series analysis, such as (Altintas in Int J Mach Tool Manuf 28:157–172, 1987) and (Kumar et al. in Int J Prod Res 35:739–751, 1997). With these methods, a threshold was set for binary state detection. However, the threshold value varies with cutting conditions and is difficult to determine.
Real-Time Estimation for Cutting Tool Wear Based on Modal Analysis of Monitored Signals

Yongjiao Chi,Wei Dai,Zhiyuan Lu,Meiqing Wang,Yu Zhao

DOI: https://doi.org/10.3390/app8050708

2018-05-03

Applied Sciences

Abstract:There is a growing body of literature that recognizes the importance of product safety and the quality problems during processing. The working status of cutting tools may lead to project delay and cost overrun if broken down accidentally, and tool wear is crucial to processing precision in mechanical manufacturing, therefore, this study contributes to this growing area of research by monitoring condition and estimating wear. In this research, an effective method for tool wear estimation was constructed, in which, the signal features of machining process were extracted by ensemble empirical mode decomposition (EEMD) and were used to estimate the tool wear. Based on signal analysis, vibration signals that had better linear relationship with tool wearing process were decomposed, then the intrinsic mode functions (IMFs), frequency spectrums of IMFs and the features relating to amplitude changes of frequency spectrum were obtained. The trend that tool wear changes with the features was fitted by Gaussian fitting function to estimate the tool wear. Experimental investigation was used to verify the effectiveness of this method and the results illustrated the correlation between tool wear and the modal features of monitored signals.
A Tool Wear Prediction and Monitoring Method Based on Machining Power Signals

Qi Wang,Xi Chen,Qinglong An,Ming Chen,Hun Guo,Yafeng He

DOI: https://doi.org/10.1007/s00170-023-12656-8

IF: 3.563

2023-01-01

The International Journal of Advanced Manufacturing Technology

Abstract:In the actual mechanical processing of difficult-to-process materials, normal or abnormal tool wear can lead to processing pauses or terminations, which seriously affects the processing accuracy and efficiency of workpieces, leading to workpiece scrapping. Therefore, predicting and monitoring tool wear during the actual machining process plays a crucial role in controlling tool costs and avoiding workpiece losses caused by tool wear. This paper proposed a tool wear prediction model based on power signals, which predicts tool wear by establishing a mapping between power signals and tool wear. Through drilling experiments for model calibration and validation, we verified that the proposed model can effectively predict tool wear under different parameters. In addition, based on the established prediction model, a real-time monitoring method for tool wear using power signals was proposed and implemented. Through experiments, it has been proven that the proposed method is suitable for monitoring normal and abnormal tool wear in actual machining.
Online Milling Tool Condition Monitoring with A Single Continuous Hidden Markov Models Approach

Lu Chen,Li Tieying,Liu Hongmei

2014-01-01

Journal of Vibroengineering

Abstract:The health status evolving from normal to broken condition of a milling tool is needed as an object of assessment in condition-based maintenance. This paper proposes continuous hidden Markov models (CHMM) to assess the status of the tool online based on the normal dataset in the same case. A wavelet-packet decomposition technology is used to feature extraction and the CHMM is trained by Baum-Welch algorithm. Finally, we compute the log-likelihood based on the trained CHMM for abnormal detection and health assessment in real time during the milling process. A case study on tool state estimation demonstrates the effectiveness and potential of this methodology.
An Embedded Tool Condition Monitoring System for Intelligent Machining

H. Z. Li,X. Q. Chen,H. Zeng

2004-01-01

Abstract:In precision machining processes, major problems can be related to the condition of the cutting tool. Online tool condition monitor- ing is hence of great industrial interest. To em- power the machining system with adaptivity and intelligence required, an embedded tool condi- tion monitoring system (eTCM) has been devel- oped for online detection of machining process abnormities such as tool breaking, chatter, etc. It employs multiple sensors including accelerome- ter, acoustic emission (AE) sensor and dyna- mometer to monitor an end milling process. The monitoring strategy, hardware architecture, monitoring algorithms and results are introduced and discussed in this paper.
Real-time tool condition monitoring method based on in situ temperature measurement and artificial neural network in turning

Kaiwei Cao,Jinghui Han,Long Xu,Tielin Shi,Guanglan Liao,Zhiyong Liu

DOI: https://doi.org/10.1007/s11465-021-0661-3

IF: 4.063

2022-03-01

Frontiers of Mechanical Engineering

Abstract:Tool failures in machining processes often cause severe damages of workpieces and lead to large quantities of loss, making tool condition monitoring an important, urgent issue. However, problems such as practicability still remain in actual machining. Here, a real-time tool condition monitoring method integrated in an in situ fiber optic temperature measuring apparatus is proposed. A thermal simulation is conducted to investigate how the fluctuating cutting heats affect the measuring temperatures, and an intermittent cutting experiment is carried out, verifying that the apparatus can capture the rapid but slight temperature undulations. Fourier transform is carried out. The spectrum features are then selected and input into the artificial neural network for classification, and a caution is given if the tool is worn. A learning rate adaption algorithm is introduced, greatly reducing the dependence on initial parameters, making training convenient and flexible. The accuracy stays 90% and higher in variable argument processes. Furthermore, an application program with a graphical user interface is constructed to present real-time results, confirming the practicality.

engineering, mechanical

An Adaptive Alarm Method for Tool Condition Monitoring Based on Probability Density Functions Estimated with the Parzen Window

A Self-Adaptive Alarm Method for Tool Condition Monitoring Based on Parzen Window Estimation

Comprehensive alarm method for equipment conditions based on parzen window estimation

On-line tool condition monitoring based on intelligent-alarm

Adaptive Alarm Technology of Tool Breakage Based on Wavelet Packet and Probabilistic Neural Network

Monitoring of Dynamic Process Using Hierarchical Probability Density Decomposition

A flexible principle component analysis method for process monitoring

Process monitoring based on factor analysis: Probabilistic analysis of monitoring statistics in presence of both complete and incomplete measurements

On-line tool wear monitoring under variable milling conditions based on a condition-adaptive hidden semi-Markov model (CAHSMM)

A condition monitoring approach for machining process based on control chart pattern recognition with dynamically-sized observation windows

On-line Monitoring for Cutting Tool Wear Reliability Analysis

A Hybrid-Driven Probabilistic State Space Model for Tool Wear Monitoring

In-situ tool wear condition monitoring during the end milling process based on dynamic mode and abnormal evaluation

Real-time Tool Breakage Monitoring Based on Dimensionless Indicators under Time-Varying Cutting Conditions

Dynamic probabilistic predictable feature analysis for multivariate temporal process monitoring

Tool Condition Monitoring with Sparse Decomposition

Real-Time Estimation for Cutting Tool Wear Based on Modal Analysis of Monitored Signals

A Tool Wear Prediction and Monitoring Method Based on Machining Power Signals

Online Milling Tool Condition Monitoring with A Single Continuous Hidden Markov Models Approach

An Embedded Tool Condition Monitoring System for Intelligent Machining

Real-time tool condition monitoring method based on in situ temperature measurement and artificial neural network in turning